Add support for Titan TNETV1050,1055,1056,1060 variants. This SoC is almost
completely identical to AR7 except on a few points:
- a second bank of gpios is available
- vlynq0 on titan is vlynq1 on ar7
- different PHY addresses for cpmac0

This SoC can be found on commercial products like the Linksys WRTP54G

Original patch by Xin with improvments by Florian.
Signed-off-by: NXin Zhen <xlonestar2000@aim.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1563/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

In order to detect the Titan variant, we must initialize GPIOs earlier since
detection relies on some GPIO values to be set.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1562/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

Declare that OCTEON reference boards have both OHCI and EHCI.

Add platform devices for the corresponding hardware.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1676/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus.  This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.

The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.

The ehci and ohci blocks share a common clocking and PHY
infrastructure.  Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.

Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The EHCI and OHCI blocks connection to the I/O bus is controlled by
these registers.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1674/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/include/asm/octeon/cvmx-uctlx-defs.h

The CN63XXP1 needs a couple of workarounds to ensure memory is not written
in unexpected ways.

All PREF with hints in the range 0-4,6-24 are replaced with PREF 28.  We
pass a flag to the assembler to cover compiler generated code, and patch
uasm for the dynamically generated code.

The write buffer threshold is reduced to 4.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1672/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The creation of the I/O clock domain requires some adjustments.  Since
the watchdog counters are clocked by the I/O clock, use its rate for
timing calculations.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1659/Acked-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The creation of the I/O clock domain requires some adjustments.  Since the
CF bus timing logic is clocked by the I/O clock, use its rate for delay
calculations.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1660/Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The I2C and UARTS are clocked by the I/O clock, use its rate for these
devices.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1670/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Starting with cn63xx Octeon I/O blocks are clocked at a different rate
than the CPU.  Add a new function octeon_get_io_clock_rate() that
yields the I/O clock rate.

Also rearrange octeon_get_clock_rate() to get the value from the saved
sysinfo structure.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1671/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We can run with any simulator clock rate.  Get rid of the code
overriding it to 6MHz.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1669/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The per-CPU clocks are synchronized from IPD_CLK_COUNT, on cn63XX it must
be scaled by the clock frequency ratio.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1667/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1666/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The OCTEON II ISA extends the original OCTEON ISA, so give it its own
__elf_platform string so optimized libraries can be selected in
userspace.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1665/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1664/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1662/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The CN63XX has a different L2 cache architecture.  Update the helper
functions to reflect this.

Some joining of split lines was also done to improve readability, as
well as reformatting of comments.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1663/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1661/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The CN63XX is a new 6-CPU SOC based on the new OCTEON II CPU cores.

Join some lines back together.  This makes some of them exceed 80
columns, but they are uninteresting and this unclutters things.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1668/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All Octeon chips can support more than 4GB of RAM.  Also due to how Octeon
PCI is setup, even some configurations with less than 4GB of RAM will have
portions that are not accessible from 32-bit devices.

Enable the swiotlb code to handle the cases where a device cannot directly
do DMA.  This is a complete rewrite of the Octeon DMA mapping code.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1639/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This allows platforms that are using the swiotlb to initialize it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1638/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use asm-generic/dma-mapping-common.h to handle all DMA mapping operations
and establish a default get_dma_ops() that forwards all operations to the
existing code.

Augment dev_archdata to carry a pointer to the struct dma_map_ops, allowing
DMA operations to be overridden on a per device basis.  Currently this is
never filled in, so the default dma_map_ops are used.  A follow-on patch
sets this for Octeon PCI devices.

Also initialize the dma_debug system as it is now used if it is configured.

Includes fixes by Kevin Cernekee <cernekee@gmail.com>.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1637/
Patchwork: http://patchwork.linux-mips.org/patch/1678/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Any function defined in a header file should be inline.  This helps us
avoid 'unused' compiler warnings when we include the files in more
places in subsequent patches.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1636/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Give us a nice place to allocate coherent DMA memory for 32-bit devices.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1635/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On OCTEON, we reserve the last 256MB of 32-bit PCI address space, mapping
the RAM in this region at a high DMA address.  This makes memory in this
region unavailable for 32-bit DMA.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1634/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

DMA mapping may reduce the usable physical address range usable for
32-bit DMA.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1633/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This allows follow-on patches to dma mapping functions to work with
the octeon mgmt device..
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1632/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add stackoverflow detection to mips arch
Signed-off-by: NAdam Jiang <jiang.adam@gmail.com>
Cc: dmitri.vorobiev@movial.com
Cc: wuzhangjin@gmail.com
Cc: ddaney@caviumnetworks.com
Cc: peterz@infradead.org
Cc: fweisbec@gmail.com
Cc: tj@kernel.org
Cc: tglx@linutronix.de
Cc: mingo@elte.hu
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1559/
Patchwork: https://patchwork.linux-mips.org/patch/1651/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/Kconfig already sets GENERIC_HARDIRQS_NO__DO_IRQ unconditionally.
Remove the redundant select from the Loongson Kconfig.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

All callers were passing in 1 anyway.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

It was a nice optimization - on paper at least.  In practice it results in
branches that may exceed the maximum legal range for a branch.  We can
fight that problem with -ffunction-sections but -ffunction-sections again
is incompatible with -pg used by the function tracer.

By rewriting the loop around all simple LL/SC blocks to C we reduce the
amount of inline assembler and at the same time allow GCC to often fill
the branch delay slots with something sensible or whatever else clever
optimization it may have up in its sleeve.

With this optimization gone we also no longer need -ffunction-sections,
so drop it.

This optimization was originally introduced in 2.6.21, commit
5999eca25c1fd4b9b9aca7833b04d10fe4bc877d (linux-mips.org) rsp.
f65e4fa8 (kernel.org).

Original fix for the issues which caused me to pull this optimization by
Paul Gortmaker <paul.gortmaker@windriver.com>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Merge branch 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
  and branch 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm

* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
  xen: register xen pci notifier
  xen: initialize cpu masks for pv guests in xen_smp_init
  xen: add a missing #include to arch/x86/pci/xen.c
  xen: mask the MTRR feature from the cpuid
  xen: make hvc_xen console work for dom0.
  xen: add the direct mapping area for ISA bus access
  xen: Initialize xenbus for dom0.
  xen: use vcpu_ops to setup cpu masks
  xen: map a dummy page for local apic and ioapic in xen_set_fixmap
  xen: remap MSIs into pirqs when running as initial domain
  xen: remap GSIs as pirqs when running as initial domain
  xen: introduce XEN_DOM0 as a silent option
  xen: map MSIs into pirqs
  xen: support GSI -> pirq remapping in PV on HVM guests
  xen: add xen hvm acpi_register_gsi variant
  acpi: use indirect call to register gsi in different modes
  xen: implement xen_hvm_register_pirq
  xen: get the maximum number of pirqs from xen
  xen: support pirq != irq

* 'stable/xen-pcifront-0.8.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: (27 commits)
  X86/PCI: Remove the dependency on isapnp_disable.
  xen: Update Makefile with CONFIG_BLOCK dependency for biomerge.c
  MAINTAINERS: Add myself to the Xen Hypervisor Interface and remove Chris Wright.
  x86: xen: Sanitse irq handling (part two)
  swiotlb-xen: On x86-32 builts, select SWIOTLB instead of depending on it.
  MAINTAINERS: Add myself for Xen PCI and Xen SWIOTLB maintainer.
  xen/pci: Request ACS when Xen-SWIOTLB is activated.
  xen-pcifront: Xen PCI frontend driver.
  xenbus: prevent warnings on unhandled enumeration values
  xenbus: Xen paravirtualised PCI hotplug support.
  xen/x86/PCI: Add support for the Xen PCI subsystem
  x86: Introduce x86_msi_ops
  msi: Introduce default_[teardown|setup]_msi_irqs with fallback.
  x86/PCI: Export pci_walk_bus function.
  x86/PCI: make sure _PAGE_IOMAP it set on pci mappings
  x86/PCI: Clean up pci_cache_line_size
  xen: fix shared irq device passthrough
  xen: Provide a variant of xen_poll_irq with timeout.
  xen: Find an unbound irq number in reverse order (high to low).
  xen: statically initialize cpu_evtchn_mask_p
  ...

Fix up trivial conflicts in drivers/pci/Makefile

* 'packaging' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  scripts/package: don't break if %{_smp_mflags} isn't set
  kbuild, deb-pkg: Check if KBUILD_IMAGE exists before copying it

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (39 commits)
  Revert "namespace: add source file location exceptions"
  Coccinelle: Add contextual message
  Coccinelle: Fix documentation
  Coccinelle: Find doubled arguments to boolean or bit operators.
  Coccinelle: Find nested lock+irqsave functions that use the same flags variables.
  namespace: add source file location exceptions
  scripts/extract-ikconfig: add support for bzip2, lzma and lzo
  kbuild: check return value of asprintf()
  scripts/namespace.pl: improve to get more correct results
  scripts/namespace.pl: some bug fixes
  scripts/namespace.pl: update file exclusion list
  scripts/namespace.pl: fix wrong source path
  Coccinelle: Use the -no_show_diff option for org and report mode
  Coccinelle: Add a new mode named 'chain'
  Coccinelle: Use new comment format to explain kfree.cocci
  Coccinelle: Improve user information with a new kind of comment
  Coccinelle: Update documentation
  MAINTAINERS: Coccinelle: Update email address
  Documentation/kbuild: modules.txt cleanup
  Documentation/kbuild: major edit of modules.txt sections 5-8
  ...

* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (38 commits)
  kbuild: convert `arch/tile' to the kconfig mainmenu upgrade
  README: cite nconfig
  Revert "kconfig: Temporarily disable dependency warnings"
  kconfig: Use PATH_MAX instead of 128 for path buffer sizes.
  kconfig: Fix realloc usage()
  kconfig: Propagate const
  kconfig: Don't go out from read config loop when you read new symbol
  kconfig: fix menuconfig on debian lenny
  kbuild: migrate all arch to the kconfig mainmenu upgrade
  kconfig: expand file names
  kconfig: use the file's name of sourced file
  kconfig: constify file name
  kconfig: don't emit warning upon rootmenu's prompt redefinition
  kconfig: replace KERNELVERSION usage by the mainmenu's prompt
  kconfig: delay gconf window initialization
  kconfig: expand by default the rootmenu's prompt
  kconfig: add a symbol string expansion helper
  kconfig: regen parser
  kconfig: implement the `mainmenu' directive
  kconfig: allow PACKAGE to be defined on the compiler's command-line
  ...

Fix up trivial conflict in arch/mn10300/Kconfig

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (73 commits)
  power: Revert "power_supply: Mark twl4030_charger as broken"
  mfd: Fix a memory leak when unload mc13xxx-core module
  mfd: Fix resource reclaim for max8998
  mfd: Remove unneeded ret value checking for max8998 register updates
  mfd: Add free max8998->ono irq in max8998_irq_exit()
  mfd: Fix resource reclaim in pcf50633_remove()
  omap4: pandaboard: fix up mmc card detect logic
  mfd: Fix ezx_pcap_probe error path
  mfd: Fix off-by-one value range checking for tps6507x
  mfd: Remove __devinitdata from tc6393xb_mmc_resources
  mfd: Add WM831x SPI support
  mfd: Factor out WM831x I2C I/O from the core driver
  mfd: Remove DEBUG defines from mc13xxx-core
  mfd: Fix jz4740_adc_set_enabled
  mfd: Add TPS658621C device ID
  mfd: Fix twl-irq function declaration warnings
  regulator: max8998 BUCK1/2 voltage change with use of GPIOs
  mfd: Voltages and GPIOs platform_data definitions for max8998
  regulator: max8998 BUCK1/2 internal voltages and indexes defined
  mfd: Support for ICs compliant with max8998
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  watchdog: iTCO_wdt.c: remove extra pci_dev_put()'s from init code
  watchdog: add support for Broadcom BCM63xx built-in watchdog
  watchdog: f71808e_wdt: add support for the F71889FG
  watchdog: MachZ: fix debug macro
  watchdog: it8712f_wdt: Add module parameter for alternative reset sources
  watchdog: it8712f_wdt: Add comments for config/control register names
  watchdog: it87_wdt: Add support for watchdogs with 8b timers
  watchdog: it87_wdt: Add support for IT8720F watchdog
  watchdog:  Use static const char * const where possible
  watchdog: iTCO_wdt: Cleanup warning messages
  watchdog: iTCO_wdt: TCO Watchdog patch for Intel Patsburg DeviceIDs

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: BUG_ON fix: check if page has buffers before calling page_buffers()

The iTCO_wdt driver erroneously releases the pci_dev, and causes PCI hotremove
to fail because of an incorrect usage count.

The probe for this driver does a for_each_pci_dev() which gets a reference for
a pci_dev when iTCO_wdt_init() is successful.  The for_each_pci_dev() loop
puts a reference for a pci_dev when iTCO_wdt_init() fails, so the
iTCO_wdt_init() does not need to do any pci_dev_put()'s.

The only pci_dev_put() that is required is in the iTCO_wdt_cleanup() function.
Signed-off-by: NPrarit Bhargava <prarit@redhat.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>