- 02 7月, 2014 3 次提交
-
-
由 Florian Fainelli 提交于
Hardware will provide this information as soon as we will start processing incoming packets, so there is no need to set the RX buffer length during buffer allocation. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
We use the PHY library which will determine the link state for us, make sure we start with a carrier off until libphy has completed the link training. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
As soon as register_netdev() is called, the network device notifiers are running which means that other parts of the kernel, or user-space programs can call the network device ndo_open() callback and use the interface. Disable the Ethernet device clock before we register the network device such that we do not create the following situation: CPU0 CPU1 register_netdev() bcmgenet_open() clk_prepare_enable() clk_disable_unprepare() and leave the hardware block gated off, while we think it should be gated on. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 5月, 2014 1 次提交
-
-
由 Wilfried Klaebe 提交于
net: get rid of SET_ETHTOOL_OPS Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone. This does that. Mostly done via coccinelle script: @@ struct ethtool_ops *ops; struct net_device *dev; @@ - SET_ETHTOOL_OPS(dev, ops); + dev->ethtool_ops = ops; Compile tested only, but I'd seriously wonder if this broke anything. Suggested-by: NDave Miller <davem@davemloft.net> Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de> Acked-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 4月, 2014 1 次提交
-
-
由 Sachin Kamat 提交于
version.h inclusion is not necessary as detected by versioncheck. Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 3月, 2014 1 次提交
-
-
由 Florian Fainelli 提交于
When the UniMAC block is configured to forward the CRC as part of the Ethernet frame (priv->crc_fwd_en, set by default), enabling the hardware RX checksum block unveiled that the dma_rxchk_bit was never set in the per-packet status bits (dma_flag in bcmgenet_desc_rx). This would make the chksum_ok variable to be never set to 1, and the networking stack would have to compute the packet checksums, which takes a substantial amount of time. In order for the RXCHK block to properly compute the packet checksum in hardware, we also need to set the RBUF_SKIP_FCS bit accordingly. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 21 3月, 2014 4 次提交
-
-
由 Florian Fainelli 提交于
Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer once and for all and manipulate it throughout bcmgenet_xmit() and bcmgenet_tx_reclaim(). Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
netdev_pick_tx already takes care of making sure that a given skb->queue_mapping value will remain within the number of advertised hardware queue number, there is no need to re-do this again in the driver. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
The BCMGENET driver was not TX timestamping the SKBs it queued for transmission, do this in bcmgenet_xmit() right before kicking the Transmit DMA engine. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
The spinlock cookie in bcmgenet_priv is never used, get rid of it. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 2月, 2014 4 次提交
-
-
由 Florian Fainelli 提交于
This code is commented since it is unused, left-over from the very first time this driver was merged. Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Fainelli 提交于
Drop all the checks on priv->phydev since we will refuse probing the driver if we cannot attach to a PHY device. Drop all checks on priv->phydev. This also fixes some smatch issues reported by Dan Carpenter. Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Fabio Estevam 提交于
According to Documentation/driver-model/devres.txt, devm_request_and_ioremap() is deprecated, so use devm_ioremap_resource() instead. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Acked-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 2月, 2014 1 次提交
-
-
由 Florian Fainelli 提交于
This patch adds the BCMGENET main driver file which supports the following: - GENET hardware from V1 to V4 - support for reading the UniMAC MIB counters statistics - support for the 5 transmit queues - support for RX/TX checksum offload and SG Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-