This patch fixes a regression introduced by the following patch:
"ar9170: load firmware asynchronously"

When we kick off a firmware loading request and then unbind,
or disconnect the usb device right away, we get into trouble:

> ------------[ cut here ]------------
> WARNING: at lib/kref.c:44 kref_get+0x1c/0x20()
> Hardware name: 18666GU
> Modules linked in: ar9170usb [...]
> Pid: 6588, comm: firmware/ar9170 Not tainted 2.6.34-rc5-wl #43
> Call Trace:
> [<c102b05e>] ? warn_slowpath_common+0x6e/0xb0
> [<c117c93c>] ? kref_get+0x1c/0x20
> [<c102b0b3>] ? warn_slowpath_null+0x13/0x20
> [<c117c93c>] ? kref_get+0x1c/0x20
> [<c117bb2f>] ? kobject_get+0xf/0x20
> [<c124d630>] ? get_device+0x10/0x20
> [<c124e5a0>] ? device_add+0x60/0x530
> [<c117b8b5>] ? kobject_init+0x25/0xa0
> [<c12569f9>] ? _request_firmware+0x139/0x3e0
> [<c1256cc0>] ? request_firmware_work_func+0x20/0x70
> [<c1256ca0>] ? request_firmware_work_func+0x0/0x70
> [<c103ff24>] ? kthread+0x74/0x80
> [<c103feb0>] ? kthread+0x0/0x80
> [<c1003136>] ? kernel_thread_helper+0x6/0x10
>---[ end trace 2d50bd818f64a1b7 ]---
- followed by a random Oops -

Avoid that by waiting for the firmware loading to finish
(whether successfully or not) before the unbind in
ar9170_usb_disconnect.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Bug-fixed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some firmware versions don't behave properly when
passive scanning is requested on radar channels
without enabling active scanning on receiving a
good frame. Work around that issue by asking the
firmware to only enable the active scanning after
receiving a huge number of good frames, a number
that can never be reached during our dwell time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Hans de Goede identified a bug in p54p_check_tx_ring:

there are two ring indices. 1 => tx data and 3 => tx management.
But the old code had a constant "1" and this resulted in spurious
dma unmapping failures.

Cc: stable@kernel.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623Bug-Identified-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since "mac80211: make off-channel work generic" drivers have not been
notified of configuration changes after association or authentication. This
caused more dependence on current state to ensure driver will be notified
when configuration changes occur. One such problem arises if off-channel is
in progress when HT information changes. Since HT is only enabled on the
"oper_channel" the driver will never be notified of this change. Usually
the driver is notified soon after of a BSS information change
(BSS_CHANGED_HT) ... but since the driver did not get a notification that
this is a HT channel the new BSS information does not make sense.

Fix this by also changing the off-channel information when HT is enabled
and thus cause driver to be notified correctly.

This fixes a problem in 4965 when associated with 5GHz 40MHz channel.
Without this patch the system can associate but is unable to transfer any
data, not even ping.

See http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2158Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the addba timer expires but has no work to do,
it should not affect the state machine. If it does,
TX will not see the successfully established and we
can also crash trying to re-establish the session.

Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.

Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported

And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When an internal scan is started, nothing protects the
is_internal_short_scan variable which can cause crashes,
cf. https://bugzilla.kernel.org/show_bug.cgi?id=15667.
Fix this by making the short scan request use the mutex
for locking, which requires making the request go to a
work struct so that it can sleep.
Reported-by: NPeter Zijlstra <peterz@infradead.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The current algorithm will sometimes "detect" that
more chains are enabled than are really present in
the device because, for unknown reasons, the ucode
sends up all-zeroes signal values.

The simplest way of solving this is to restrict the
active chains mask to the chains we know are really
present on the device.

This fixes a bug with some devices where, since sometimes
more chains are enabled than really present, the system would hang.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

For 4965, need to check it is valid qos frame before free, only valid
QoS frame has the tid used to free the packets.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With the enable_radio being uninitialized, ath_radio_enable() might be
called twice, which can leave some hardware in an undefined state.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new RCU lockdep support warns about these
in some contexts -- make it aware of the locks
used to protect all this. Different locks are
used in different contexts which unfortunately
means we can't get perfect checking.

Also remove rcu_dereference() from two places
that don't actually dereference the pointers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the problem introduced in commit
84040805 which broke mesh peer link establishment.

changes:
v2 	Added missing break (Johannes)
v3 	Broke original patch into two (Johannes)
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.

This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().

To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NHenry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Below warning is triggered sometimes at module removal time when
CONFIG_DMA_API_DEBUG is enabled. This should be caused by we didn't
unmap pending commands (enqueued, but no complete notification
received) for the Tx command queue.

[ 1583.107469] ------------[ cut here ]------------
[ 1583.107539] WARNING: at lib/dma-debug.c:688
dma_debug_device_change+0x13c/0x180()
[ 1583.107617] Hardware name: ...
[ 1583.107664] pci 0000:04:00.0: DMA-API: device driver has pending DMA
allocations while released from device [count=1]
[ 1583.107713] Modules linked in: ...
[ 1583.111661] Pid: 16970, comm: modprobe Tainted: G        W
2.6.34-rc1-wl #33
[ 1583.111727] Call Trace:
[ 1583.111779]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111833]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.111908]  [<c0138e11>] warn_slowpath_common+0x71/0xd0
[ 1583.111963]  [<c02a281c>] ? dma_debug_device_change+0x13c/0x180
[ 1583.112016]  [<c0138ebb>] warn_slowpath_fmt+0x2b/0x30
[ 1583.112086]  [<c02a281c>] dma_debug_device_change+0x13c/0x180
[ 1583.112142]  [<c03e6c33>] notifier_call_chain+0x53/0x90
[ 1583.112198]  [<c03e1ebe>] ? down_read+0x6e/0x90
[ 1583.112271]  [<c015b229>] __blocking_notifier_call_chain+0x49/0x70
[ 1583.112326]  [<c015b26f>] blocking_notifier_call_chain+0x1f/0x30
[ 1583.112380]  [<c031931c>] __device_release_driver+0x8c/0xa0
[ 1583.112451]  [<c03193bf>] driver_detach+0x8f/0xa0
[ 1583.112538]  [<c0318382>] bus_remove_driver+0x82/0x100
[ 1583.112595]  [<c0319ad9>] driver_unregister+0x49/0x80
[ 1583.112671]  [<c024feb2>] ? sysfs_remove_file+0x12/0x20
[ 1583.112727]  [<c02aa292>] pci_unregister_driver+0x32/0x80
[ 1583.112791]  [<fc13a3c1>] iwl_exit+0x12/0x19 [iwlagn]
[ 1583.112848]  [<c017940a>] sys_delete_module+0x15a/0x210
[ 1583.112870]  [<c015a5db>] ? up_read+0x1b/0x30
[ 1583.112893]  [<c029600c>] ? trace_hardirqs_off_thunk+0xc/0x10
[ 1583.112924]  [<c0295ffc>] ? trace_hardirqs_on_thunk+0xc/0x10
[ 1583.112947]  [<c03e6a1f>] ? do_page_fault+0x1ff/0x3c0
[ 1583.112978]  [<c03e36f6>] ? restore_all_notrace+0x0/0x18
[ 1583.113002]  [<c016aa70>] ? trace_hardirqs_on_caller+0x20/0x190
[ 1583.113025]  [<c0102d58>] sysenter_do_call+0x12/0x38
[ 1583.113054] ---[ end trace fc23e059cc4c2ced ]---
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

The libertas driver calls wiphy_unregister() without a prior
wiphy_register() when a devices fails initialization. Fix this by
introducing a private flag.

[    9.310000] Unable to handle kernel NULL pointer dereference at virtual address 00000000

[...]

[    9.330000] [<c0311310>] (wiphy_unregister+0xfc/0x19c) from [<bf00c9ec>] (lbs_cfg_free+0x70/0x9c [libertas])
[    9.330000] [<bf00c9ec>] (lbs_cfg_free+0x70/0x9c [libertas]) from [<bf014fdc>] (lbs_remove_card+0x180/0x210 [libertas])
[    9.330000] [<bf014fdc>] (lbs_remove_card+0x180/0x210 [libertas]) from [<bf035394>] (if_sdio_probe+0xdc4/0xef4 [libertas_sdio])
[    9.330000] [<bf035394>] (if_sdio_probe+0xdc4/0xef4 [libertas_sdio]) from [<c0230d14>] (sdio_bus_probe+0xd4/0xf0)
[    9.330000] [<c0230d14>] (sdio_bus_probe+0xd4/0xf0) from [<c01a6034>] (driver_probe_device+0xa4/0x174)
[    9.330000] [<c01a6034>] (driver_probe_device+0xa4/0x174) from [<c01a6164>] (__driver_attach+0x60/0x84)
[    9.330000] [<c01a6164>] (__driver_attach+0x60/0x84) from [<c01a5854>] (bus_for_each_dev+0x4c/0x8c)
[    9.330000] [<c01a5854>] (bus_for_each_dev+0x4c/0x8c) from [<c01a50e4>] (bus_add_driver+0xa0/0x228)
[    9.330000] [<c01a50e4>] (bus_add_driver+0xa0/0x228) from [<c01a6470>] (driver_register+0xc0/0x150)
[    9.330000] [<c01a6470>] (driver_register+0xc0/0x150) from [<bf03a06c>] (if_sdio_init_module+0x6c/0x108 [libertas_sdio])
[    9.330000] [<bf03a06c>] (if_sdio_init_module+0x6c/0x108 [libertas_sdio]) from [<c00263ac>] (do_one_initcall+0x5c/0x1bc)
[    9.330000] [<c00263ac>] (do_one_initcall+0x5c/0x1bc) from [<c0069f80>] (sys_init_module+0xc0/0x1f0)
[    9.330000] [<c0069f80>] (sys_init_module+0xc0/0x1f0) from [<c0026f00>] (ret_fast_syscall+0x0/0x30)
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IWL_RATE_COUNT is 13 and IWL_RATE_COUNT_LEGACY is 12.

IWL_RATE_COUNT_LEGACY is the right one here because iwl3945_rates
doesn't support 60M and also that's how "rates" is defined in
iwlcore_init_geos() from drivers/net/wireless/iwlwifi/iwl-core.c.

        rates = kzalloc((sizeof(struct ieee80211_rate) * IWL_RATE_COUNT_LEGACY),
                        GFP_KERNEL);
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: stable@kernel.org
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

An int urb is constructed but we fill it in with a bulk pipe type.

Commit f661c6f8 implemented a pipe type
check when CONFIG_USB_DEBUG is enabled. The check failed for all the ar9170
usb transfers and the driver could not configure the wifi dongle.

This went unnoticed until now because most people don't have
CONFIG_USB_DEBUG enabled.
Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Stable <stable@kernel.org>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Recent bug reports have shown that rt2500usb also suffers from the
powersave problems that the PCI rt2x00 drivers suffer from.
So disable powersaving by default for rt2500usb as well.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously in interrupt handling tasklet, iwlwifi driver only clear/ack
those interrupts that are enabled by the driver through inta_mask.
If the hardware generates unattended interrupts, driver will not ack them,
defeating the interrupt coalescing feature. This results in high number
of interrupts per second and high CPU utilization.

This patch addresses this issue by acking those unattended interrupts
in the tasklet. Local test showed an order of magnitude improvement
in terms of the number of interrupts without sacrificing networking
throughput. This is a workaround for hardware issue.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Forget one hunk in 4965 during "iwlwifi: error checking for number of tfds
in queue" patch.
Reported-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org

Commit "cfg80211: convert bools into flags" mistakenly modified iwlwifi's
regulatory settings instead of just converting it. Fix this.

This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2172Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org

"mac80211: fix skb buffering issue" still left a race
between enabling the hardware queues and the virtual
interface queues. In hindsight it's totally obvious
that enabling the netdev queues for a hardware queue
when the hardware queue is enabled is wrong, because
it could well possible that we can fill the hw queue
with packets we already have pending. Thus, we must
only enable the netdev queues once all the pending
packets have been processed and sent off to the device.

In testing, I haven't been able to trigger this race
condition, but it's clearly there, possibly only when
aggregation is being enabled.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Thanks to Chris Chabot for giving his old wireless usb dongle to me
to test it under Linux.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBenjamin Larsson <banan@ludd.ltu.se>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for the NEC WL300NU-G USB wifi dongle.
Signed-off-by: NBen Konrath <ben@bagu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

1st) a PREQ should only be processed, if it has the same SN and better
metric (instead of better or equal).
2nd) next_hop[ETH_ALEN] now actually used to buffer
mpath->next_hop->sta.addr for use out of lock.
Signed-off-by: NMarco Porsch <marco.porsch@siemens.com>
Acked-by: NJavier Cardona <javier@cozybit.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stanse discovered that kmalloc is being called with GFP_KERNEL while
holding this spinlock.  The spinlock can be a mutex instead, which also
enables the removal of the unlock/lock around the lock/unlock of
cfg80211_mutex and the call to set_regdom.
Reported-by: NJiri Slaby <jirislaby@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit a239a8b4 introduced a
noisy message, that fills up the log very fast.

The error seems not to be fatal (the connection is stable and
performance is ok), so make it IWL_DEBUG_TX rather than IWL_ERR.
Signed-off-by: NAdel Gadllah <adel.gadllah@gmail.com>
Cc: stable@kernel.org
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When I initially stumbled upon sequence number problems with PAE frames
in ath9k, I submitted a patch to remove all special cases for PAE
frames and let them go through the normal transmit path.
Out of concern about crypto incompatibility issues, this change was
merged instead:

commit 6c8afef5
Author: Sujith <Sujith.Manoharan@atheros.com>
Date:   Tue Feb 9 10:07:00 2010 +0530

    ath9k: Fix sequence numbers for PAE frames

After a lot of testing, I'm able to reliably trigger a driver crash on
rekeying with current versions with this change in place.
It seems that the driver does not support sending out regular MPDUs with
the same TID while an A-MPDU session is active.
This leads to duplicate entries in the TID Tx buffer, which hits the
following BUG_ON in ath_tx_addto_baw():

    index  = ATH_BA_INDEX(tid->seq_start, bf->bf_seqno);
    cindex = (tid->baw_head + index) & (ATH_TID_MAX_BUFS - 1);

    BUG_ON(tid->tx_buf[cindex] != NULL);

I believe until we actually have a reproducible case of an
incompatibility with another AP using no PAE special cases, we should
simply get rid of this mess.

This patch completely fixes my crash issues in STA mode and makes it
stay connected without throughput drops or connectivity issues even
when the AP is configured to a very short group rekey interval.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In case debugfs does not init for some reason (or is disabled
on older kernels) driver does not allocate stats.fw_stats
structure, but tries to clear it later and trips on a NULL
pointer:

Unable to handle kernel NULL pointer dereference at virtual address
00000000
PC is at __memzero+0x24/0x80
Backtrace:
[<bf0ddb88>] (wl1251_debugfs_reset+0x0/0x30 [wl1251])
[<bf0d6a2c>] (wl1251_op_stop+0x0/0x12c [wl1251])
[<bf0bc228>] (ieee80211_stop_device+0x0/0x74 [mac80211])
[<bf0b0d10>] (ieee80211_stop+0x0/0x4ac [mac80211])
[<c02deeac>] (dev_close+0x0/0xb4)
[<c02deac0>] (dev_change_flags+0x0/0x184)
[<c031f478>] (devinet_ioctl+0x0/0x704)
[<c0320720>] (inet_ioctl+0x0/0x100)

Add a NULL pointer check to fix this.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NKalle Valo <kalle.valo@iki.fi>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix memory leak and use kmalloc() instead of kzalloc() as we are going
to overwrite the allocated buffer.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently hardware with !IEEE80211_HW_PS_NULLFUNC_STACK and
IEEE80211_HW_REPORTS_TX_ACK_STATUS will never enter PSM due to the
conditions in the power save entry functions.

Fix those conditions.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Cc: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixed below compiler warning:

drivers/net/wireless/ipw2x00/ipw2200.c: In function ‘ipw_load_firmware’:
drivers/net/wireless/ipw2x00/ipw2200.c:3260: warning: the frame size of
1168 bytes is larger than 1024 bytes
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

we read the IQ correction values (i_cal and q_cal) for G mode from a wrong
location (the same shifts as for A mode is applied which is incorrect). use
correct locations, matching the docs and HAL sources.

also we should write IQ correction only when we have that information in the
EEPROM, starting from version 4. also write it in the same way as we do in the
periodic recalibration (enable last), just to be sure.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I/Q calibration was completely broken, resulting in a high number of CRC errors
on received packets. before i could see around 10% to 20% CRC errors, with this
patch they are between 0% and 3%.

1.) the removal of the mask in commit "ath5k: Fix I/Q calibration
(f1cf2dbd)" resulted in no mask beeing used
when writing the I/Q values into the register. additional errors in the
calculation of the values (see 2.) resulted too high numbers, exceeding the
masks, so wrong values like 0xfffffffe were written. to be safe we should
always use the bitmask when writing parts of a register.

2.) using a (s32) cast for q_coff is a wrong conversion to signed, since we
convert to a signed value later by substracting 128. this resulted in too low
numbers for Q many times, which were limited to -16 by the boundary check later
on.

3.) checked everything against the HAL sources and took over comments and minor
optimizations from there.

4.) we can't use ENABLE_BITS when we want to write a number (the number can
contain zeros). also always write the correction values first and set ENABLE
bit last, like the HAL does.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Cc: stable@kernel.org
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>