- 23 4月, 2018 4 次提交
-
-
由 Vignesh R 提交于
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on return value of device_may_wakeup() in .suspend(). This allows userspace to use sysfs to control the ability of UART to wakeup the system from deep sleep state. Register is restored back in .startup() call that happens as part of resume sequence. With this patch, userspace can control UART wakeup capability via sysfs: To enable wakeup capability: echo enabled > /sys/class/tty/ttyXX/device/power/wakeup For disabling wakeup capability: echo disabled > /sys/class/tty/ttyXX/device/power/wakeup Note that the UART wakeup events configured in the 8250 hardware only work for idle modes that do not cut off power for the UART. For deeper idle states, dedicated padconf wakeirqs must be used. Or in some cases the UART RX pin can be remuxed to GPIO input if the GPIO block stays powered. Signed-off-by: NVignesh R <vigneshr@ti.com> Tested-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Joshua Scott 提交于
The previous implementation has had a detrimental effect on devices using high bitrates (bluetooth), as the fifo being non-empty for a single check would result in a 10 µs delay. Limit the change to devices with the new "marvell,armada-38x-uart" compatible string. Also update the code to allow the first 1000 retries to not perform a delay. The maximum duration of retries has been increased to cover a worst-case seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with text to output before doing a resize. At 9600 baud this took up to 13 ms to flush all characters and avoid some getting lost. Signed-off-by: NJoshua Scott <joshua.scott@alliedtelesis.co.nz> Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Ulrich Hecht 提交于
HSCIF has facilities that allow moving the RX sampling point by between -8 and 7 sampling cycles (one sampling cycles equals 1/15 of a bit by default) to improve the error margin in case of slightly mismatched bit rates between sender and receiver. This patch tries to determine if shifting the sampling point can improve the error margin and will enable it if so. Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Geert Uytterhoeven 提交于
On DT platforms, the sh-sci driver requires the presence of "serialN" aliases in DT, from which instance IDs are derived. If a DT alias is missing, the drivers fails to probe the corresponding serial port. This becomes cumbersome when considering DT overlays, as currently there is no upstream support for dynamically updating the /aliases node in DT. Furthermore, even in the presence of such support, hardcoded instance IDs in independent overlays are prone to conflicts. Hence add support for dynamic instance IDs, to be used in the absence of a DT alias. This makes serial ports behave similar to I2C and SPI buses, which already support dynamic instances. Ports in use are tracked using a simple bitmask of type unsigned long, which is sufficient to handle all current hardware (max. 18 ports). The maximum number of serial ports is still fixed, and configurable through Kconfig. Range validation is done through both Kconfig and a compile-time check. Due to the fixed maximum number of serial ports, dynamic and static instances share the same ID space. Static instances added later are rejected when conflicting with dynamic instances registered earlier. Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 22 4月, 2018 3 次提交
-
-
由 Miquel Raynal 提交于
Add suspend and resume hooks to save/restore the registers content during S2RAM operation. Also save/restore the oversampling rate register (OSAMP) as earlier stages already tuned that register to get a precise UART clock. Suggested-by: NAllen Yan <yanwei@marvell.com> Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Pascal Huerst 提交于
Without this, tx stops working after resume. By adding these calls, everything seems to work fine. Signed-off-by: NPascal Huerst <pascal.huerst@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
由 Wolfram Sang 提交于
We should get drvdata from struct device directly. Going via platform_device is an unneeded step back and forth. Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NPatrice Chotard <patrice.chotard@st.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 16 4月, 2018 13 次提交
-
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux由 Linus Torvalds 提交于
Pull more btrfs updates from David Sterba: "We have queued a few more fixes (error handling, log replay, softlockup) and the rest is SPDX updates that touche almost all files so the diffstat is long" * tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: Only check first key for committed tree blocks btrfs: add SPDX header to Kconfig btrfs: replace GPL boilerplate by SPDX -- sources btrfs: replace GPL boilerplate by SPDX -- headers Btrfs: fix loss of prealloc extents past i_size after fsync log replay Btrfs: clean up resources during umount after trans is aborted btrfs: Fix possible softlock on single core machines Btrfs: bail out on error during replay_dir_deletes Btrfs: fix NULL pointer dereference in log_dir_items
-
git://git.samba.org/sfrench/cifs-2.6由 Linus Torvalds 提交于
Pull cifs fixes from Steve French: "SMB3 fixes, a few for stable, and some important cleanup work from Ronnie of the smb3 transport code" * tag '4.17-rc1SMB3-Fixes' of git://git.samba.org/sfrench/cifs-2.6: cifs: change validate_buf to validate_iov cifs: remove rfc1002 hardcoded constants from cifs_discard_remaining_data() cifs: Change SMB2_open to return an iov for the error parameter cifs: add resp_buf_size to the mid_q_entry structure smb3.11: replace a 4 with server->vals->header_preamble_size cifs: replace a 4 with server->vals->header_preamble_size cifs: add pdu_size to the TCP_Server_Info structure SMB311: Improve checking of negotiate security contexts SMB3: Fix length checking of SMB3.11 negotiate request CIFS: add ONCE flag for cifs_dbg type cifs: Use ULL suffix for 64-bit constant SMB3: Log at least once if tree connect fails during reconnect cifs: smb2pdu: Fix potential NULL pointer dereference
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi由 Linus Torvalds 提交于
Pull SCSI fixes from James Bottomley: "This is a set of minor (and safe changes) that didn't make the initial pull request plus some bug fixes. The status handling code is actually a running regression from the previous merge window which had an incomplete fix (now reverted) and most of the remaining bug fixes are for problems older than the current merge window" [ Side note: this merge also takes the base kernel git repository to 6+ million objects for the first time. Technically we hit it a couple of merges ago already if you count all the tag objects, but now it reaches 6M+ objects reachable from HEAD. I was joking around that that's when I should switch to 5.0, because 3.0 happened at the 2M mark, and 4.0 happened at 4M objects. But probably not, even if numerology is about as good a reason as any. - Linus ] * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: devinfo: Add Microsoft iSCSI target to 1024 sector blacklist scsi: cxgb4i: silence overflow warning in t4_uld_rx_handler() scsi: dpt_i2o: Use after free in I2ORESETCMD ioctl scsi: core: Make scsi_result_to_blk_status() recognize CONDITION MET scsi: core: Rename __scsi_error_from_host_byte() into scsi_result_to_blk_status() Revert "scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()" scsi: aacraid: Insure command thread is not recursively stopped scsi: qla2xxx: Correct setting of SAM_STAT_CHECK_CONDITION scsi: qla2xxx: correctly shift host byte scsi: qla2xxx: Fix race condition between iocb timeout and initialisation scsi: qla2xxx: Avoid double completion of abort command scsi: qla2xxx: Fix small memory leak in qla2x00_probe_one on probe failure scsi: scsi_dh: Don't look for NULL devices handlers by name scsi: core: remove redundant assignment to shost->use_blk_mq
-
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild由 Linus Torvalds 提交于
Pull more Kbuild updates from Masahiro Yamada: - pass HOSTLDFLAGS when compiling single .c host programs - build genksyms lexer and parser files instead of using shipped versions - rename *-asn1.[ch] to *.asn1.[ch] for suffix consistency - let the top .gitignore globally ignore artifacts generated by flex, bison, and asn1_compiler - let the top Makefile globally clean artifacts generated by flex, bison, and asn1_compiler - use safer .SECONDARY marker instead of .PRECIOUS to prevent intermediate files from being removed - support -fmacro-prefix-map option to make __FILE__ a relative path - fix # escaping to prepare for the future GNU Make release - clean up deb-pkg by using debian tools instead of handrolled source/changes generation - improve rpm-pkg portability by supporting kernel-install as a fallback of new-kernel-pkg - extend Kconfig listnewconfig target to provide more information * tag 'kbuild-v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: kconfig: extend output of 'listnewconfig' kbuild: rpm-pkg: use kernel-install as a fallback for new-kernel-pkg Kbuild: fix # escaping in .cmd files for future Make kbuild: deb-pkg: split generating packaging and build kbuild: use -fmacro-prefix-map to make __FILE__ a relative path kbuild: mark $(targets) as .SECONDARY and remove .PRECIOUS markers kbuild: rename *-asn1.[ch] to *.asn1.[ch] kbuild: clean up *-asn1.[ch] patterns from top-level Makefile .gitignore: move *-asn1.[ch] patterns to the top-level .gitignore kbuild: add %.dtb.S and %.dtb to 'targets' automatically kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically genksyms: generate lexer and parser during build instead of shipping kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile .gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore kbuild: use HOSTLDFLAGS for single .c executables
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Thomas Gleixner: "A set of fixes and updates for x86: - Address a swiotlb regression which was caused by the recent DMA rework and made driver fail because dma_direct_supported() returned false - Fix a signedness bug in the APIC ID validation which caused invalid APIC IDs to be detected as valid thereby bloating the CPU possible space. - Fix inconsisten config dependcy/select magic for the MFD_CS5535 driver. - Fix a corruption of the physical address space bits when encryption has reduced the address space and late cpuinfo updates overwrite the reduced bit information with the original value. - Dominiks syscall rework which consolidates the architecture specific syscall functions so all syscalls can be wrapped with the same macros. This allows to switch x86/64 to struct pt_regs based syscalls. Extend the clearing of user space controlled registers in the entry patch to the lower registers" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/apic: Fix signedness bug in APIC ID validity checks x86/cpu: Prevent cpuinfo_x86::x86_phys_bits adjustment corruption x86/olpc: Fix inconsistent MFD_CS5535 configuration swiotlb: Use dma_direct_supported() for swiotlb_ops syscalls/x86: Adapt syscall_wrapper.h to the new syscall stub naming convention syscalls/core, syscalls/x86: Rename struct pt_regs-based sys_*() to __x64_sys_*() syscalls/core, syscalls/x86: Clean up compat syscall stub naming convention syscalls/core, syscalls/x86: Clean up syscall stub naming convention syscalls/x86: Extend register clearing on syscall entry to lower registers syscalls/x86: Unconditionally enable 'struct pt_regs' based syscalls on x86_64 syscalls/x86: Use 'struct pt_regs' based syscall calling for IA32_EMULATION and x32 syscalls/core: Prepare CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y for compat syscalls syscalls/x86: Use 'struct pt_regs' based syscall calling convention for 64-bit syscalls syscalls/core: Introduce CONFIG_ARCH_HAS_SYSCALL_WRAPPER=y x86/syscalls: Don't pointlessly reload the system call number x86/mm: Fix documentation of module mapping range with 4-level paging x86/cpuid: Switch to 'static const' specifier
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 pti updates from Thomas Gleixner: "Another series of PTI related changes: - Remove the manual stack switch for user entries from the idtentry code. This debloats entry by 5k+ bytes of text. - Use the proper types for the asm/bootparam.h defines to prevent user space compile errors. - Use PAGE_GLOBAL for !PCID systems to gain back performance - Prevent setting of huge PUD/PMD entries when the entries are not leaf entries otherwise the entries to which the PUD/PMD points to and are populated get lost" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/pgtable: Don't set huge PUD/PMD on non-leaf entries x86/pti: Leave kernel text global for !PCID x86/pti: Never implicitly clear _PAGE_GLOBAL for kernel image x86/pti: Enable global pages for shared areas x86/mm: Do not forbid _PAGE_RW before init for __ro_after_init x86/mm: Comment _PAGE_GLOBAL mystery x86/mm: Remove extra filtering in pageattr code x86/mm: Do not auto-massage page protections x86/espfix: Document use of _PAGE_GLOBAL x86/mm: Introduce "default" kernel PTE mask x86/mm: Undo double _PAGE_PSE clearing x86/mm: Factor out pageattr _PAGE_GLOBAL setting x86/entry/64: Drop idtentry's manual stack switch for user entries x86/uapi: Fix asm/bootparam.h userspace compilation errors
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull scheduler fixes from Thomas Gleixner: "A few scheduler fixes: - Prevent a bogus warning vs. runqueue clock update flags in do_sched_rt_period_timer() - Simplify the helper functions which handle requests for skipping the runqueue clock updat. - Do not unlock the tunables mutex in the error path of the cpu frequency scheduler utils. Its not held. - Enforce proper alignement for 'struct util_est' in sched_avg to prevent a misalignment fault on IA64" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/core: Force proper alignment of 'struct util_est' sched/core: Simplify helpers for rq clock update skip requests sched/rt: Fix rq->clock_update_flags < RQCF_ACT_SKIP warning sched/cpufreq/schedutil: Fix error path mutex unlock
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull more perf updates from Thomas Gleixner: "A rather large set of perf updates: Kernel: - Fix various initialization issues - Prevent creating [ku]probes for not CAP_SYS_ADMIN users Tooling: - Show only failing syscalls with 'perf trace --failure' (Arnaldo Carvalho de Melo) e.g: See what 'openat' syscalls are failing: # perf trace --failure -e openat 762.323 ( 0.007 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video2) = -1 ENOENT No such file or directory <SNIP N /dev/videoN open attempts... sigh, where is that improvised camera lid?!? > 790.228 ( 0.008 ms): VideoCapture/4566 openat(dfd: CWD, filename: /dev/video63) = -1 ENOENT No such file or directory ^C# - Show information about the event (freq, nr_samples, total period/nr_events) in the annotate --tui and --stdio2 'perf annotate' output, similar to the first line in the 'perf report --tui', but just for the samples for a the annotated symbol (Arnaldo Carvalho de Melo) - Introduce 'perf version --build-options' to show what features were linked, aliased as well as a shorter 'perf -vv' (Jin Yao) - Add a "dso_size" sort order (Kim Phillips) - Remove redundant ')' in the tracepoint output in 'perf trace' (Changbin Du) - Synchronize x86's cpufeatures.h, no effect on toolss (Arnaldo Carvalho de Melo) - Show group details on the title line in the annotate browser and 'perf annotate --stdio2' output, so that the per-event columns can have headers (Arnaldo Carvalho de Melo) - Fixup vertical line separating metrics from instructions and cleaning unused lines at the bottom, both in the annotate TUI browser (Arnaldo Carvalho de Melo) - Remove duplicated 'samples' in lost samples warning in 'perf report' (Arnaldo Carvalho de Melo) - Synchronize i915_drm.h, silencing the perf build process, automagically adding support for the new DRM_I915_QUERY ioctl (Arnaldo Carvalho de Melo) - Make auxtrace_queues__add_buffer() allocate struct buffer, from a patchkit already applied (Adrian Hunter) - Fix the --stdio2/TUI annotate output to include group details, be it for a recorded '{a,b,f}' explicit event group or when forcing group display using 'perf report --group' for a set of events not recorded as a group (Arnaldo Carvalho de Melo) - Fix display artifacts in the ui browser (base class for the annotate and main report/top TUI browser) related to the extra title lines work (Arnaldo Carvalho de Melo) - perf auxtrace refactorings, leftovers from a previously partially processed patchset (Adrian Hunter) - Fix the builtin clang build (Sandipan Das, Arnaldo Carvalho de Melo) - Synchronize i915_drm.h, silencing a perf build warning and in the process automagically adding support for a new ioctl command (Arnaldo Carvalho de Melo) - Fix a strncpy issue in uprobe tracing" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits) perf/core: Need CAP_SYS_ADMIN to create k/uprobe with perf_event_open() tracing/uprobe_event: Fix strncpy corner case perf/core: Fix perf_uprobe_init() perf/core: Fix perf_kprobe_init() perf/core: Fix use-after-free in uprobe_perf_close() perf tests clang: Fix function name for clang IR test perf clang: Add support for recent clang versions perf tools: Fix perf builds with clang support perf tools: No need to include namespaces.h in util.h perf hists browser: Remove leftover from row returned from refresh perf hists browser: Show extra_title_lines in the 'D' debug hotkey perf auxtrace: Make auxtrace_queues__add_buffer() do CPU filtering tools headers uapi: Synchronize i915_drm.h perf report: Remove duplicated 'samples' in lost samples warning perf ui browser: Fixup cleaning unused lines at the bottom perf annotate browser: Fixup vertical line separating metrics from instructions perf annotate: Show group details on the title line perf auxtrace: Make auxtrace_queues__add_buffer() allocate struct buffer perf/x86/intel: Move regs->flags EXACT bit init perf trace: Remove redundant ')' ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 EFI bootup fixlet from Thomas Gleixner: "A single fix for an early boot warning caused by invoking this_cpu_has() before SMP initialization" * 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/mm: Fix bogus warning during EFI bootup, use boot_cpu_has() instead of this_cpu_has() in build_cr3_noflush()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull irq affinity fixes from Thomas Gleixner: - Fix error path handling in the affinity spreading code - Make affinity spreading smarter to avoid issues on systems which claim to have hotpluggable CPUs while in fact they can't hotplug anything. So instead of trying to spread the vectors (and thereby the associated device queues) to all possibe CPUs, spread them on all present CPUs first. If there are left over vectors after that first step they are spread among the possible, but not present CPUs which keeps the code backwards compatible for virtual decives and NVME which allocate a queue per possible CPU, but makes the spreading smarter for devices which have less queues than possible or present CPUs. * 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/affinity: Spread irq vectors among present CPUs as far as possible genirq/affinity: Allow irq spreading from a given starting point genirq/affinity: Move actual irq vector spreading into a helper function genirq/affinity: Rename *node_to_possible_cpumask as *node_to_cpumask genirq/affinity: Don't return with empty affinity masks on error
-
git://github.com/openrisc/linux由 Linus Torvalds 提交于
Pull OpenRISC fixlet from Stafford Horne: "Just one small thing here, it came in a while back but I didnt have anything in my 4.16 queue, still its the only thing for 4.17 so sending it alone. Small cleanup: remove unused __ARCH_HAVE_MMU define" * tag 'for-linus' of git://github.com/openrisc/linux: openrisc: remove unused __ARCH_HAVE_MMU define
-
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux由 Linus Torvalds 提交于
Pull powerpc fixes from Michael Ellerman: - Fix crashes when loading modules built with a different CONFIG_RELOCATABLE value by adding CONFIG_RELOCATABLE to vermagic. - Fix busy loops in the OPAL NVRAM driver if we get certain error conditions from firmware. - Remove tlbie trace points from KVM code that's called in real mode, because it causes crashes. - Fix checkstops caused by invalid tlbiel on Power9 Radix. - Ensure the set of CPU features we "know" are always enabled is actually the minimal set when we build with support for firmware supplied CPU features. Thanks to: Aneesh Kumar K.V, Anshuman Khandual, Nicholas Piggin. * tag 'powerpc-4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/64s: Fix CPU_FTRS_ALWAYS vs DT CPU features powerpc/mm/radix: Fix checkstops caused by invalid tlbiel KVM: PPC: Book3S HV: trace_tlbie must not be called in realmode powerpc/8xx: Fix build with hugetlbfs enabled powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops powerpc/fscr: Enable interrupts earlier before calling get_user() powerpc/64s: Fix section mismatch warnings from setup_rfi_flush() powerpc/modules: Fix crashes by adding CONFIG_RELOCATABLE to vermagic
-
- 14 4月, 2018 20 次提交
-
-
由 Linus Torvalds 提交于
Merge yet more updates from Andrew Morton: - various hotfixes - kexec_file updates and feature work * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits) kernel/kexec_file.c: move purgatories sha256 to common code kernel/kexec_file.c: allow archs to set purgatory load address kernel/kexec_file.c: remove mis-use of sh_offset field during purgatory load kernel/kexec_file.c: remove unneeded variables in kexec_purgatory_setup_sechdrs kernel/kexec_file.c: remove unneeded for-loop in kexec_purgatory_setup_sechdrs kernel/kexec_file.c: split up __kexec_load_puragory kernel/kexec_file.c: use read-only sections in arch_kexec_apply_relocations* kernel/kexec_file.c: search symbols in read-only kexec_purgatory kernel/kexec_file.c: make purgatory_info->ehdr const kernel/kexec_file.c: remove checks in kexec_purgatory_load include/linux/kexec.h: silence compile warnings kexec_file, x86: move re-factored code to generic side x86: kexec_file: clean up prepare_elf64_headers() x86: kexec_file: lift CRASH_MAX_RANGES limit on crash_mem buffer x86: kexec_file: remove X86_64 dependency from prepare_elf64_headers() x86: kexec_file: purge system-ram walking from prepare_elf64_headers() kexec_file,x86,powerpc: factor out kexec_file_ops functions kexec_file: make use of purgatory optional proc: revalidate misc dentries mm, slab: reschedule cache_reap() on the same CPU ...
-
由 Philipp Rudo 提交于
The code to verify the new kernels sha digest is applicable for all architectures. Move it to common code. One problem is the string.c implementation on x86. Currently sha256 includes x86/boot/string.h which defines memcpy and memset to be gcc builtins. By moving the sha256 implementation to common code and changing the include to linux/string.h both functions are no longer defined. Thus definitions have to be provided in x86/purgatory/string.c Link: http://lkml.kernel.org/r/20180321112751.22196-12-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
For s390 new kernels are loaded to fixed addresses in memory before they are booted. With the current code this is a problem as it assumes the kernel will be loaded to an 'arbitrary' address. In particular, kexec_locate_mem_hole searches for a large enough memory region and sets the load address (kexec_bufer->mem) to it. Luckily there is a simple workaround for this problem. By returning 1 in arch_kexec_walk_mem, kexec_locate_mem_hole is turned off. This allows the architecture to set kbuf->mem by hand. While the trick works fine for the kernel it does not for the purgatory as here the architectures don't have access to its kexec_buffer. Give architectures access to the purgatories kexec_buffer by changing kexec_load_purgatory to take a pointer to it. With this change architectures have access to the buffer and can edit it as they need. A nice side effect of this change is that we can get rid of the purgatory_info->purgatory_load_address field. As now the information stored there can directly be accessed from kbuf->mem. Link: http://lkml.kernel.org/r/20180321112751.22196-11-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Reviewed-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
The current code uses the sh_offset field in purgatory_info->sechdrs to store a pointer to the current load address of the section. Depending whether the section will be loaded or not this is either a pointer into purgatory_info->purgatory_buf or kexec_purgatory. This is not only a violation of the ELF standard but also makes the code very hard to understand as you cannot tell if the memory you are using is read-only or not. Remove this misuse and store the offset of the section in pugaroty_info->purgatory_buf in sh_offset. Link: http://lkml.kernel.org/r/20180321112751.22196-10-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
The main loop currently uses quite a lot of variables to update the section headers. Some of them are unnecessary. So clean them up a little. Link: http://lkml.kernel.org/r/20180321112751.22196-9-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
To update the entry point there is an extra loop over all section headers although this can be done in the main loop. So move it there and eliminate the extra loop and variable to store the 'entry section index'. Also, in the main loop, move the usual case, i.e. non-bss section, out of the extra if-block. Link: http://lkml.kernel.org/r/20180321112751.22196-8-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Reviewed-by: NMartin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
When inspecting __kexec_load_purgatory you find that it has two tasks 1) setting up the kexec_buffer for the new kernel and, 2) setting up pi->sechdrs for the final load address. The two tasks are independent of each other. To improve readability split up __kexec_load_purgatory into two functions, one for each task, and call them directly from kexec_load_purgatory. Link: http://lkml.kernel.org/r/20180321112751.22196-7-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
When the relocations are applied to the purgatory only the section the relocations are applied to is writable. The other sections, i.e. the symtab and .rel/.rela, are in read-only kexec_purgatory. Highlight this by marking the corresponding variables as 'const'. While at it also change the signatures of arch_kexec_apply_relocations* to take section pointers instead of just the index of the relocation section. This removes the second lookup and sanity check of the sections in arch code. Link: http://lkml.kernel.org/r/20180321112751.22196-6-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
The stripped purgatory does not contain a symtab. So when looking for symbols this is done in read-only kexec_purgatory. Highlight this by marking the corresponding variables as 'const'. Link: http://lkml.kernel.org/r/20180321112751.22196-5-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
The kexec_purgatory buffer is read-only. Thus all pointers into kexec_purgatory are read-only, too. Point this out by explicitly marking purgatory_info->ehdr as 'const' and update the comments in purgatory_info. Link: http://lkml.kernel.org/r/20180321112751.22196-4-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
Before the purgatory is loaded several checks are done whether the ELF file in kexec_purgatory is valid or not. These checks are incomplete. For example they don't check for the total size of the sections defined in the section header table or if the entry point actually points into the purgatory. On the other hand the purgatory, although an ELF file on its own, is part of the kernel. Thus not trusting the purgatory means not trusting the kernel build itself. So remove all validity checks on the purgatory and just trust the kernel build. Link: http://lkml.kernel.org/r/20180321112751.22196-3-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Ingo Molnar <mingo@kernel.org> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Philipp Rudo 提交于
Patch series "kexec_file: Clean up purgatory load", v2. Following the discussion with Dave and AKASHI, here are the common code patches extracted from my recent patch set (Add kexec_file_load support to s390) [1]. The patches were extracted to allow upstream integration together with AKASHI's common code patches before the arch code gets adjusted to the new base. The reason for this series is to prepare common code for adding kexec_file_load to s390 as well as cleaning up the mis-use of the sh_offset field during purgatory load. In detail this series contains: Patch #1&2: Minor cleanups/fixes. Patch #3-9: Clean up the purgatory load/relocation code. Especially remove the mis-use of the purgatory_info->sechdrs->sh_offset field, currently holding a pointer into either kexec_purgatory (ro) or purgatory_buf (rw) depending on the section. With these patches the section address will be calculated verbosely and sh_offset will contain the offset of the section in the stripped purgatory binary (purgatory_buf). Patch #10: Allows architectures to set the purgatory load address. This patch is important for s390 as the kernel and purgatory have to be loaded to fixed addresses. In current code this is impossible as the purgatory load is opaque to the architecture. Patch #11: Moves x86 purgatories sha implementation to common lib/ directory to allow reuse in other architectures. This patch (of 11) When building the kernel with CONFIG_KEXEC_FILE enabled gcc prints a compile warning multiple times. In file included from <path>/linux/init/initramfs.c:526:0: <path>/include/linux/kexec.h:120:9: warning: `struct kimage' declared inside parameter list [enabled by default] unsigned long cmdline_len); ^ This is because the typedefs for kexec_file_load uses struct kimage before it is declared. Fix this by simply forward declaring struct kimage. Link: http://lkml.kernel.org/r/20180321112751.22196-2-prudo@linux.vnet.ibm.comSigned-off-by: NPhilipp Rudo <prudo@linux.vnet.ibm.com> Acked-by: NDave Young <dyoung@redhat.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Cc: Ingo Molnar <mingo@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
In the previous patches, commonly-used routines, exclude_mem_range() and prepare_elf64_headers(), were carved out. Now place them in kexec common code. A prefix "crash_" is given to each of their names to avoid possible name collisions. Link: http://lkml.kernel.org/r/20180306102303.9063-8-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
Removing bufp variable in prepare_elf64_headers() makes the code simpler and more understandable. Link: http://lkml.kernel.org/r/20180306102303.9063-7-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
While CRASH_MAX_RANGES (== 16) seems to be good enough, fixed-number array is not a good idea in general. In this patch, size of crash_mem buffer is calculated as before and the buffer is now dynamically allocated. This change also allows removing crash_elf_data structure. Link: http://lkml.kernel.org/r/20180306102303.9063-6-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
The code guarded by CONFIG_X86_64 is necessary on some architectures which have a dedicated kernel mapping outside of linear memory mapping. (arm64 is among those.) In this patch, an additional argument, kernel_map, is added to enable/ disable the code removing #ifdef. Link: http://lkml.kernel.org/r/20180306102303.9063-5-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
While prepare_elf64_headers() in x86 looks pretty generic for other architectures' use, it contains some code which tries to list crash memory regions by walking through system resources, which is not always architecture agnostic. To make this function more generic, the related code should be purged. In this patch, prepare_elf64_headers() simply scans crash_mem buffer passed and add all the listed regions to elf header as a PT_LOAD segment. So walk_system_ram_res(prepare_elf64_headers_callback) have been moved forward before prepare_elf64_headers() where the callback, prepare_elf64_headers_callback(), is now responsible for filling up crash_mem buffer. Meanwhile exclude_elf_header_ranges() used to be called every time in this callback it is rather redundant and now called only once in prepare_elf_headers() as well. Link: http://lkml.kernel.org/r/20180306102303.9063-4-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
As arch_kexec_kernel_image_{probe,load}(), arch_kimage_file_post_load_cleanup() and arch_kexec_kernel_verify_sig() are almost duplicated among architectures, they can be commonalized with an architecture-defined kexec_file_ops array. So let's factor them out. Link: http://lkml.kernel.org/r/20180306102303.9063-3-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 AKASHI Takahiro 提交于
Patch series "kexec_file, x86, powerpc: refactoring for other architecutres", v2. This is a preparatory patchset for adding kexec_file support on arm64. It was originally included in a arm64 patch set[1], but Philipp is also working on their kexec_file support on s390[2] and some changes are now conflicting. So these common parts were extracted and put into a separate patch set for better integration. What's more, my original patch#4 was split into a few small chunks for easier review after Dave's comment. As such, the resulting code is basically identical with my original, and the only *visible* differences are: - renaming of _kexec_kernel_image_probe() and _kimage_file_post_load_cleanup() - change one of types of arguments at prepare_elf64_headers() Those, unfortunately, require a couple of trivial changes on the rest (#1, #6 to #13) of my arm64 kexec_file patch set[1]. Patch #1 allows making a use of purgatory optional, particularly useful for arm64. Patch #2 commonalizes arch_kexec_kernel_{image_probe, image_load, verify_sig}() and arch_kimage_file_post_load_cleanup() across architectures. Patches #3-#7 are also intended to generalize parse_elf64_headers(), along with exclude_mem_range(), to be made best re-use of. [1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-February/561182.html [2] http://lkml.iu.edu//hypermail/linux/kernel/1802.1/02596.html This patch (of 7): On arm64, crash dump kernel's usable memory is protected by *unmapping* it from kernel virtual space unlike other architectures where the region is just made read-only. It is highly unlikely that the region is accidentally corrupted and this observation rationalizes that digest check code can also be dropped from purgatory. The resulting code is so simple as it doesn't require a bit ugly re-linking/relocation stuff, i.e. arch_kexec_apply_relocations_add(). Please see: http://lists.infradead.org/pipermail/linux-arm-kernel/2017-December/545428.html All that the purgatory does is to shuffle arguments and jump into a new kernel, while we still need to have some space for a hash value (purgatory_sha256_digest) which is never checked against. As such, it doesn't make sense to have trampline code between old kernel and new kernel on arm64. This patch introduces a new configuration, ARCH_HAS_KEXEC_PURGATORY, and allows related code to be compiled in only if necessary. [takahiro.akashi@linaro.org: fix trivial screwup] Link: http://lkml.kernel.org/r/20180309093346.GF25863@linaro.org Link: http://lkml.kernel.org/r/20180306102303.9063-2-takahiro.akashi@linaro.orgSigned-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org> Acked-by: NDave Young <dyoung@redhat.com> Tested-by: NDave Young <dyoung@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Baoquan He <bhe@redhat.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alexey Dobriyan 提交于
If module removes proc directory while another process pins it by chdir'ing to it, then subsequent recreation of proc entry and all entries down the tree will not be visible to any process until pinning process unchdir from directory and unpins everything. Steps to reproduce: proc_mkdir("aaa", NULL); proc_create("aaa/bbb", ...); chdir("/proc/aaa"); remove_proc_entry("aaa/bbb", NULL); remove_proc_entry("aaa", NULL); proc_mkdir("aaa", NULL); # inaccessible because "aaa" dentry still points # to the original "aaa". proc_create("aaa/bbb", ...); Fix is to implement ->d_revalidate and ->d_delete. Link: http://lkml.kernel.org/r/20180312201938.GA4871@avx2Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-