xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.

v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB core hub thread (khubd) is designed with external USB hubs in
mind.  It expects that if a port status change bit is set, the hub will
continue to send a notification through the hub status data transfer.
Basically, it expects hub notifications to be level-triggered.

The xHCI host controller is designed to be edge-triggered on the logical
'OR' of all the port status change bits.  When all port status change
bits are clear, and a new change bit is set, the xHC will generate a
Port Status Change Event.  If another change bit is set in the same port
status register before the first bit is cleared, it will not send
another event.

This means that the hub code may lose port status changes because of
race conditions between clearing change bits.  The user sees this as a
"dead port" that doesn't react to device connects.

The fix is to turn on port polling whenever a new change bit is set.
Once the USB core issues a hub status request that shows that no change
bits are set in any USB ports, turn off port polling.

We can't allow the USB core to poll the roothub for port events during
host suspend because if the PCI host is in D3cold, the port registers
will be all f's.  Instead, stop the port polling timer, and
unconditionally restart it when the host resumes.  If there are no port
change bits set after the resume, the first call to hub_status_data will
disable polling.

This patch should be backported to stable kernels with the first xHCI
support, 2.6.31 and newer, that include the commit
0f2a7930 "USB: xhci: Root hub support."
There will be merge conflicts because the check for HC_STATE_SUSPENDED
was moved into xhci_suspend in 3.8.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

that check will have to be done by all users
of xhci_suspend() so it sounds a lot better to
move the check to xhci_suspend() in order to
avoid code duplication.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This minor patch creates a more stricter conditional for the Z1 sytems for applying
the Compliance Mode Patch, this to avoid the quirk to be applied to models that
contain a "Z1" in their dmi product string but are different from Z1 systems.

This patch should be backported to stable kernels as old as 3.2, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

David reports that at drivers/usb/host/xhci.c:2257:

static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
    return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
}

The static analyser cppcheck says

[linux-3.7-rc2/drivers/usb/host/xhci.c:2257]: (style) Redundant condition: If ep_type == 5, the comparison ep_type != 7 is always true.

Maybe the original programmer intention was something like

static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
    return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}

Fix this.

This patch should be backported to stable kernels as old as 3.2, that
contain the commit 2b698999 "xhci: USB
3.0 BW checking."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Cc: stable@vger.kernel.org

Non-static xHCI driver symbols should start with the "xhci_" prefix, in
order to avoid namespace pollution.  Rename the "handshake" function to
"xhci_handshake".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NBen Hutchings <ben@decadent.org.uk>

Remove the variable ep_ctx from xhci_add_endpoint(), since it is
assigned but unused.  Caught by Coverity.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Coverity complains that xhci_evaluate_context_result() is missing a
break statement after the COMP_EBADSLT switch case.  It's not a big
deal, since we wanted to return the same error code as the case
statement below it does.  The end result would be one that a Slot
Disabled error completion code would also print the warning message
associated with a Context State error code.  No other bad behavior would
result.

It's not worth backporting to stable kernels, since it only fixes an
issue with too much debugging.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

xhci_service_interval_to_ns() returns long long
to avoid an overflow. However, the type cast happens
too late. The fix is to force ULL from the beginning.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org

An le16 is accessed without conversion.

This patch should be backported to kernels as old as 3.5, that contain
the commit e3567d2c "xhci: Add Intel
U1/U2 timeout policy."
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
CC: stable@vger.kernel.org

This minor change adds a new system to which the "Fix Compliance Mode
on SN65LVPE502CP Hardware" patch has to be applied also.

System added:
Vendor: Hewlett-Packard. System Model: Z1
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In 71c731a2: usb: host: xhci: Fix Compliance Mode on SN65LVPE502CP Hardware
when extracting DMI strings (vendor or product_name) to mark them as quirk
we may get NULL pointer in case of non-x86 systems which won't define
CONFIG_DMI. Hence susbsequent strstr() calls crash while driver probing.

So, returning 'false' here in case we get a NULL vendor or product_name.

This is tested with ARM (exynos) system.

This patch should be backported to stable kernels as old as 3.6, that
contain the commit 71c731a2 "usb: host:
xhci: Fix Compliance Mode on SN65LVPE502CP Hardware"
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NSebastian Gottschall (DD-WRT) <s.gottschall@dd-wrt.com>
Cc: stable@vger.kernel.org

The Intel XHCI specification says that after clearing the run/stop bit
the controller may take up to 16ms to halt. We've seen a device take
14ms, which with the current timeout of 10ms causes the kernel to
abort the suspend. Increasing the timeout to the recommended value
fixes the problem.

This patch should be backported to kernels as old as 2.6.37, that
contain the commit 5535b1d5 "USB: xHCI:
PCI power management implementation".
Signed-off-by: NMichael Spang <spang@chromium.org>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

drivers/usb/host/xhci.c:1826:14: warning: symbol 'xhci_get_block_size' was not declared. Should it be static?
drivers/usb/host/xhci.c:1844:14: warning: symbol 'xhci_get_largest_overhead' was not declared. Should it be static?
drivers/usb/host/xhci-ring.c:2304:36: warning: context imbalance in 'handle_tx_event' - unexpected unlock
drivers/usb/host/xhci-hub.c:425:6: warning: symbol 'xhci_set_remote_wake_mask' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The patch is used to cancel command when the command isn't
acknowledged and a timeout occurs.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Software have to abort command ring and cancel command
when a command is failed or hang. Otherwise, the command
ring will hang up and can't handle the others. An example
of a command that may hang is the Address Device Command,
because waiting for a SET_ADDRESS request to be acknowledged
by a USB device is outside of the xHC's ability to control.

To cancel a command, software will initialize a command
descriptor for the cancel command, and add it into a
cancel_cmd_list of xhci.

Sarah: Fixed missing newline on "Have the command ring been stopped?"
debugging statement.

This patch should be backported to kernels as old as 3.0, that contain
the commit 7ed603ec "xhci: Add an
assertion to check for virt_dev=0 bug." That commit papers over a NULL
pointer dereference, and this patch fixes the underlying issue that
caused the NULL pointer dereference.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

Adding cmd_ring_state for command ring. It helps to verify
the current command ring state for controlling the command
ring operations.

This patch should be backported to kernels as old as 3.0.  The commit
7ed603ec "xhci: Add an assertion to
check for virt_dev=0 bug." papers over the NULL pointer dereference that
I now believe is related to a timed out Set Address command.  This (and
the four patches that follow it) contain the real fix that also allows
VIA USB 3.0 hubs to consistently re-enumerate during the plug/unplug
stress tests.
Signed-off-by: NElric Fu <elricfu1@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NMiroslav Sabljic <miroslav.sabljic@avl.com>
Cc: stable@vger.kernel.org

This patch is intended to work around a known issue on the
SN65LVPE502CP USB3.0 re-driver that can delay the negotiation
between a device and the host past the usual handshake timeout.

If that happens on the first insertion, the host controller
port will enter in Compliance Mode and NO port status event will
be generated (as per xHCI Spec) making impossible to detect this
event by software. The port will remain in compliance mode until
a warm reset is applied to it.

As a result of this, the port will seem "dead" to the user and no
device connections or disconnections will be detected.

For solving this, the patch creates a timer which polls every 2
seconds the link state of each host controller's port (this
by reading the PORTSC register) and recovers the port by issuing a
Warm reset every time Compliance mode is detected.

If a xHC USB3.0 port has previously entered to U0, the compliance
mode issue will NOT occur only until system resumes from
sleep/hibernate, therefore, the compliance mode timer is stopped
when all xHC USB 3.0 ports have entered U0. The timer is initialized
again after each system resume.

Since the issue is being caused by a piece of hardware, the timer
will be enabled ONLY on those systems that have the SN65LVPE502CP
installed (this patch uses DMI strings for detecting those systems)
therefore making this patch to act as a quirk (XHCI_COMP_MODE_QUIRK
has been added to the xhci stack).

This patch applies for these systems:
Vendor: Hewlett-Packard. System Models: Z420, Z620 and Z820.

This patch should be backported to kernels as old as 3.2, as that was
the first kernel to support warm reset.  The kernels will need to
contain both commit 10d674a8 "USB: When
hot reset for USB3 fails, try warm reset" and commit
8bea2bd3 "usb: Add support for root hub
port status CAS".  The first patch add warm reset support, and the
second patch modifies the USB core to issue a warm reset when the port
is in compliance mode.
Signed-off-by: NAlexis R. Cortes <alexis.cortes@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The intent was to test whether the flag was set.

This patch should be backported to stable kernels as old as 3.0, since
it fixes a bug in commit e95829f4 "xhci:
Switch PPT ports to EHCI on shutdown.", which was marked for stable.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

The Intel desktop boards DH77EB and DH77DF have a hardware issue that
can be worked around by BIOS.  If the USB ports are switched to xHCI on
shutdown, the xHCI host will send a spurious interrupt, which will wake
the system.  Some BIOS will work around this, but not all.

The bug can be avoided if the USB ports are switched back to EHCI on
shutdown.  The Intel Windows driver switches the ports back to EHCI, so
change the Linux xHCI driver to do the same.

Unfortunately, we can't tell the two effected boards apart from other
working motherboards, because the vendors will change the DMI strings
for the DH77EB and DH77DF boards to their own custom names.  One example
is Compulab's mini-desktop, the Intense-PC.  Instead, key off the
Panther Point xHCI host PCI vendor and device ID, and switch the ports
over for all PPT xHCI hosts.

The only impact this will have on non-effected boards is to add a couple
hundred milliseconds delay on boot when the BIOS has to switch the ports
over from EHCI to xHCI.

This patch should be backported to kernels as old as 3.0, that contain
the commit 69e848c2 "Intel xhci: Support
EHCI/xHCI port switching."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDenis Turischev <denis@compulab.co.il>
Tested-by: NDenis Turischev <denis@compulab.co.il>
Cc: stable@vger.kernel.org

The NEC/Renesas 720201 xHCI host controller does not complete its reset
within 250 milliseconds.  In fact, it takes about 9 seconds to reset the
host controller, and 1 second for the host to be ready for doorbell
rings.  Extend the reset and CNR polling timeout to 10 seconds each.

This patch should be backported to kernels as old as 2.6.31, that
contain the commit 66d4eadd "USB: xhci:
BIOS handoff and HW initialization."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NEdwin Klein Mentink <e.kleinmentink@zonnet.nl>
Cc: stable@vger.kernel.org

There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.

This patch besides adding the new ioctl also adds flags for the following
existing capabilities:

USBDEVFS_CAP_ZERO_PACKET,        available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION,  available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3

Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.

Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.

The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.

xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.

Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.

This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5 "USB: xHCI:
PCI power management implementation"
Signed-off-by: NAndiry Xu <andiry.xu@gmail.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org

This patch fixes an issue discovered by Dan Carpenter:

The patch 3b3db026: "xhci: Add infrastructure for host-specific
LPM policies." from May 9, 2012, leads to the following warning:
drivers/usb/host/xhci.c:3909 xhci_get_timeout_no_hub_lpm()
         warn: signedness bug returning '-22'

  3906          default:
  3907                  dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
  3908                                  __func__);
  3909                  return -EINVAL;
                        ^^^^^^^^^^^^^^
This should be a u16 like USB3_LPM_DISABLED or something.

  3910          }
  3911
  3912          if (sel <= max_sel_pel && pel <= max_sel_pel)
  3913                  return USB3_LPM_DEVICE_INITIATED;
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>

Fengguang reports that the xHCI driver isn't linked properly on his
machine:

ERROR: "__udivdi3" [drivers/usb/host/xhci-hcd.ko] undefined!
ERROR: "handle_edge_irq" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_to_desc" [drivers/gpio/gpio-pch.ko] undefined!

The driver compiles fine on my 64-bit box (gcc version 4.6.1).
Fengguang thinks it's because the xHCI driver was using DIV_ROUND_UP()
instead of DIV_ROUND_UP_ULL() with arguments that were unsigned long
long variables.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NWu Fengguang <wfg@linux.intel.com>

The USB 2.0 Link PM code is conditionally compiled when
CONFIG_USB_SUSPEND=y.  I believe that's a mistake, since Link PM is not
directly related to USB device suspend and Link PM is implemented
without relying on any of the suspend code in the USB core.  For now,
keep the USB 2.0 Link PM code conditionally compiled if
CONFIG_USB_SUSPEND=y.

This patch does move the code to implement USB 3.0 Link PM out of the
xHCI driver #ifdefs for CONFIG_USB_SUSPEND and moves it into a section
dependent on CONFIG_PM.  The USB core functions for USB 3.0 Link PM are
already conditionally compiled when CONFIG_PM=y.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

All Intel xHCI host controllers support USB 3.0 Link Power Management.

The Panther Point xHCI host controller needs the xHCI driver to
calculate the U1 and U2 timeout values, because it will blindly accept a
MEL that would cause scheduling issues.

The Lynx Point xHCI host controller will reject MEL values that are too
high, but internally it implements the same algorithm that is needed for
Panther Point xHCI.

Simplify the code paths by just having the xHCI driver calculate what
the U1/U2 timeouts should be.  Comments on the policy are in the code.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The choice of U1 and U2 timeouts for USB 3.0 Link Power Management (LPM)
is highly host controller specific.  Here are a few examples of why it's
host specific:

 1. Setting the U1/U2 timeout too short may cause the link to go into
    U1/U2 in between service intervals, which some hosts may tolerate,
    and some may not.

 2. The host controller has to modify its bus schedule in order to take
    into account the Maximum Exit Latency (MEL) to bring all the links
    from the host to the device into U0.  If the MEL is too big, and it
    takes too long to bring the links into an active state, the host
    controller may not be able to service periodic endpoints in time.

 3. Host controllers may also have scheduling limitations that force
    them to disable U1 or U2 if a USB device is behind too many tiers of
    hubs.

We could take an educated guess at what U1/U2 timeouts may work for a
particular host controller.  However, that would result in a binary
search on every new configuration or alt setting installation, with
multiple failed Evaluate Context commands.  Worse, the host may blindly
accept the timeouts and just fail to update its schedule for U1/U2 exit
latencies, which could result in randomly delayed periodic transfers.

Since we don't want to cause jitter in periodic transfers, or delay
config/alt setting changes too much, lay down a framework that xHCI
vendors can extend in order to add their own U1/U2 timeout policies.

To extend the framework, they will need to:

 - Modify the PCI init code to add a new xhci->quirk for their host, and
   set the XHCI_LPM_SUPPORT quirk flag.
 - Add their own vendor-specific hooks, like the ones that will be added
   in xhci_call_host_update_timeout_for_endpoint() and
   xhci_check_tier_policy()
 - Make the LPM enable/disable methods call those functions based on the
   xhci->quirk for their host.

An example will be provided for the Intel xHCI host controller in the
next patch.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The upcoming USB 3.0 Link PM patches will introduce new API to enable
and disable low-power link states.  We must be able to disable LPM in
order to reset a device, or place the device into U3 (device suspend).
Therefore, we need to make sure the Evaluate Context command to disable
the LPM timeouts can't fail due to there being no room on the command
ring.

Introduce a new flag to the function that queues the Evaluate Context
command, command_must_succeed.  This tells the ring handler that a TRB
has already been reserved for the command (by incrementing
xhci->cmd_ring_reserved_trbs), and basically ensures that prepare_ring()
won't fail.  A similar flag was already implemented for the Configure
Endpoint command queuing function.

All functions that currently call xhci_configure_endpoint() to issue an
Evaluate Context command pass "false" for the "must_succeed" parameter,
so this patch should have no effect on current xHCI driver behavior.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Testing BUILD_BUG_ON xhci_doorbell_array structure 2 time, redundant statement
Signed-off-by: NGirish Verma <girish.gcet@gmail.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>

 ---
 drivers/usb/host/xhci.c |    1 -
 1 files changed, 0 insertions(+), 1 deletions(-)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.

This patch should be backported to kernels as old as 3.4, that contain
the commit 879d38e6 "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org

The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in.  It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last.  I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled.  Therefore we need to restore the event ring registers
before we re-enable interrupts.

This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5 "USB: xHCI: PCI power
management implementation"
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NElric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org

The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it.  No other code in the xHCI successful resume path would
ever restore it either.  Fix that.

This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5 "USB: xHCI: PCI power
management implementation".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NElric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org

Eric Fu reports a problem with his VIA host controller fetching a zeroed
event ring pointer on resume from suspend.  The host should have been
halted, but we can't be sure because that code ignores the return value
from xhci_halt().  Print a warning when the host controller refuses to
halt within XHCI_MAX_HALT_USEC (currently 16 seconds).

(Update: it turns out that the VIA host controller is reporting a halted
state when it fetches the zeroed event ring pointer.  However, we still
need this warning for other host controllers.)
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This adds a fairly simple xhci-platform driver support. Currently it is
used by the dwc3 driver for supporting host mode.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Update sg tablesize as we can expand the ring now.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NPaul Zimmerman <Paul.Zimmerman@synopsys.com>

In the past, the room_on_ring() check was implemented by walking all over
the ring, which is wasteful and complicated.

Count the number of free TRBs instead. The free TRBs number should be
updated when enqueue/dequeue pointer is updated, or upon the completion
of a set dequeue pointer command.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: NPaul Zimmerman <Paul.Zimmerman@synopsys.com>

The latest released errata for USB2.0 ECN LPM adds new fields to USB2.0
extension descriptor, defines two BESL values for device: baseline BESL
and deep BESL. Baseline BESL value communicates a nominal power savings
design point and the deep BESL value communicates a significant power
savings design point.

If device indicates BESL value, driver will use a value count in both
host BESL and device BESL. Use baseline BESL value as default.
Signed-off-by: NAndiry Xu <andiry.xu@amd.com>
Tested-by: NJason Fan <jcfan@qca.qualcomm.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

There's really no point in having hcd->irq as a
signed integer when we consider the fact that
IRQ 0 means NO_IRQ. In order to avoid confusion,
make hcd->irq unsigned and fix users who were
passing -1 as the IRQ number to usb_add_hcd.
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS.  The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.

Actually, Linux also can work for MSI.  This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe.  It allows the xHCI driver
to try to enable MSI or MSI-X first.  It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.

This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: NAlex Shi <alex.shi@intel.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org