提交 ebebd9b0 编写于 作者: R Russell King 提交者: Russell King

[ARM] pxa: update PXA MMC interface driver to use clk support

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
上级 22d8a73a
......@@ -23,6 +23,8 @@
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/dma-mapping.h>
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/mmc/host.h>
#include <asm/dma.h>
......@@ -44,6 +46,8 @@ struct pxamci_host {
spinlock_t lock;
struct resource *res;
void __iomem *base;
struct clk *clk;
unsigned long clkrate;
int irq;
int dma;
unsigned int clkrt;
......@@ -119,7 +123,7 @@ static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
writel(nob, host->base + MMC_NOB);
writel(data->blksz, host->base + MMC_BLKLEN);
clks = (unsigned long long)data->timeout_ns * CLOCKRATE;
clks = (unsigned long long)data->timeout_ns * host->clkrate;
do_div(clks, 1000000000UL);
timeout = (unsigned int)clks + (data->timeout_clks << host->clkrt);
writel((timeout + 255) / 256, host->base + MMC_RDTO);
......@@ -365,18 +369,25 @@ static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
struct pxamci_host *host = mmc_priv(mmc);
if (ios->clock) {
unsigned int clk = CLOCKRATE / ios->clock;
if (CLOCKRATE / clk > ios->clock)
unsigned long rate = host->clkrate;
unsigned int clk = rate / ios->clock;
/*
* clk might result in a lower divisor than we
* desire. check for that condition and adjust
* as appropriate.
*/
if (rate / clk > ios->clock)
clk <<= 1;
host->clkrt = fls(clk) - 1;
pxa_set_cken(CKEN_MMC, 1);
clk_enable(host->clk);
/*
* we write clkrt on the next command
*/
} else {
pxamci_stop_clock(host);
pxa_set_cken(CKEN_MMC, 0);
clk_disable(host->clk);
}
if (host->power_mode != ios->power_mode) {
......@@ -462,8 +473,6 @@ static int pxamci_probe(struct platform_device *pdev)
}
mmc->ops = &pxamci_ops;
mmc->f_min = CLOCKRATE_MIN;
mmc->f_max = CLOCKRATE_MAX;
/*
* We can do SG-DMA, but we don't because we never know how much
......@@ -490,6 +499,22 @@ static int pxamci_probe(struct platform_device *pdev)
host->mmc = mmc;
host->dma = -1;
host->pdata = pdev->dev.platform_data;
host->clk = clk_get(&pdev->dev, "MMCCLK");
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
host->clk = NULL;
goto out;
}
host->clkrate = clk_get_rate(host->clk);
/*
* Calculate minimum clock rate, rounding up.
*/
mmc->f_min = (host->clkrate + 63) / 64;
mmc->f_max = host->clkrate;
mmc->ocr_avail = host->pdata ?
host->pdata->ocr_mask :
MMC_VDD_32_33|MMC_VDD_33_34;
......@@ -554,6 +579,8 @@ static int pxamci_probe(struct platform_device *pdev)
iounmap(host->base);
if (host->sg_cpu)
dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
if (host->clk)
clk_put(host->clk);
}
if (mmc)
mmc_free_host(mmc);
......@@ -588,6 +615,8 @@ static int pxamci_remove(struct platform_device *pdev)
iounmap(host->base);
dma_free_coherent(&pdev->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma);
clk_put(host->clk);
release_resource(host->res);
mmc_free_host(mmc);
......
......@@ -88,17 +88,3 @@
#define MMC_RXFIFO 0x0040 /* 8 bit */
#define MMC_TXFIFO 0x0044 /* 8 bit */
/*
* The base MMC clock rate
*/
#ifdef CONFIG_PXA27x
#define CLOCKRATE_MIN 304688
#define CLOCKRATE_MAX 19500000
#else
#define CLOCKRATE_MIN 312500
#define CLOCKRATE_MAX 20000000
#endif
#define CLOCKRATE CLOCKRATE_MAX
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册