提交 e5f9bf72 编写于 作者: P Philippe Proulx 提交者: Greg Kroah-Hartman

serial: omap: fix a few checkpatch warnings

Signed-off-by: NPhilippe Proulx <philippe.proulx@savoirfairelinux.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
上级 018e7448
......@@ -177,7 +177,7 @@ struct uart_omap_port {
bool is_suspending;
};
#define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port)))
#define to_uart_omap_port(p) ((container_of((p), struct uart_omap_port, port)))
static struct uart_omap_port *ui[OMAP_MAX_HSUART_PORTS];
......@@ -257,9 +257,9 @@ serial_omap_baud_is_mode16(struct uart_port *port, unsigned int baud)
unsigned int n16 = port->uartclk / (16 * baud);
int baudAbsDiff13 = baud - (port->uartclk / (13 * n13));
int baudAbsDiff16 = baud - (port->uartclk / (16 * n16));
if(baudAbsDiff13 < 0)
if (baudAbsDiff13 < 0)
baudAbsDiff13 = -baudAbsDiff13;
if(baudAbsDiff16 < 0)
if (baudAbsDiff16 < 0)
baudAbsDiff16 = -baudAbsDiff16;
return (baudAbsDiff13 >= baudAbsDiff16);
......@@ -316,9 +316,8 @@ static void serial_omap_stop_tx(struct uart_port *port)
serial_out(up, UART_OMAP_SCR, up->scr);
res = (up->rs485.flags & SER_RS485_RTS_AFTER_SEND) ? 1 : 0;
if (gpio_get_value(up->rts_gpio) != res) {
if (up->rs485.delay_rts_after_send > 0) {
if (up->rs485.delay_rts_after_send > 0)
mdelay(up->rs485.delay_rts_after_send);
}
gpio_set_value(up->rts_gpio, res);
}
} else {
......@@ -422,9 +421,8 @@ static void serial_omap_start_tx(struct uart_port *port)
res = (up->rs485.flags & SER_RS485_RTS_ON_SEND) ? 1 : 0;
if (gpio_get_value(up->rts_gpio) != res) {
gpio_set_value(up->rts_gpio, res);
if (up->rs485.delay_rts_before_send > 0) {
if (up->rs485.delay_rts_before_send > 0)
mdelay(up->rs485.delay_rts_before_send);
}
}
}
......@@ -1724,8 +1722,9 @@ static int serial_omap_probe(struct platform_device *pdev)
up->port.uartclk = omap_up_info->uartclk;
if (!up->port.uartclk) {
up->port.uartclk = DEFAULT_CLK_SPEED;
dev_warn(&pdev->dev, "No clock speed specified: using default:"
"%d\n", DEFAULT_CLK_SPEED);
dev_warn(&pdev->dev,
"No clock speed specified: using default: %d\n"
DEFAULT_CLK_SPEED);
}
up->latency = PM_QOS_CPU_DMA_LAT_DEFAULT_VALUE;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册