提交 d2cdfc0d 编写于 作者: A Alan 提交者: Jeff Garzik

libata: PIIX3 support

This I believe completes the PIIX range of support for libata

This adds the table entries needed for the PIIX3, both a new PCI
identifier and a new mode list. It also fixes an erroneous access to PCI
configuration 0x48 on non UDMA capable chips.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>
上级 fba6edbd
...@@ -118,7 +118,7 @@ enum { ...@@ -118,7 +118,7 @@ enum {
PIIX_80C_SEC = (1 << 7) | (1 << 6), PIIX_80C_SEC = (1 << 7) | (1 << 6),
/* controller IDs */ /* controller IDs */
piix_pata_33 = 0, /* PIIX3 or 4 at 33Mhz */ piix_pata_33 = 0, /* PIIX4 at 33Mhz */
ich_pata_33 = 1, /* ICH up to UDMA 33 only */ ich_pata_33 = 1, /* ICH up to UDMA 33 only */
ich_pata_66 = 2, /* ICH up to 66 Mhz */ ich_pata_66 = 2, /* ICH up to 66 Mhz */
ich_pata_100 = 3, /* ICH up to UDMA 100 */ ich_pata_100 = 3, /* ICH up to UDMA 100 */
...@@ -128,6 +128,7 @@ enum { ...@@ -128,6 +128,7 @@ enum {
ich6_sata_ahci = 7, ich6_sata_ahci = 7,
ich6m_sata_ahci = 8, ich6m_sata_ahci = 8,
ich8_sata_ahci = 9, ich8_sata_ahci = 9,
piix_pata_mwdma = 10, /* PIIX3 MWDMA only */
/* constants for mapping table */ /* constants for mapping table */
P0 = 0, /* port 0 */ P0 = 0, /* port 0 */
...@@ -165,6 +166,8 @@ static unsigned int in_module_init = 1; ...@@ -165,6 +166,8 @@ static unsigned int in_module_init = 1;
static const struct pci_device_id piix_pci_tbl[] = { static const struct pci_device_id piix_pci_tbl[] = {
#ifdef ATA_ENABLE_PATA #ifdef ATA_ENABLE_PATA
/* Intel PIIX3 for the 430HX etc */
{ 0x8086, 0x7010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_mwdma },
/* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */ /* Intel PIIX4 for the 430TX/440BX/MX chipset: UDMA 33 */
/* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */ /* Also PIIX4E (fn3 rev 2) and PIIX4M (fn3 rev 3) */
{ 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 }, { 0x8086, 0x7111, PCI_ANY_ID, PCI_ANY_ID, 0, 0, piix_pata_33 },
...@@ -441,7 +444,7 @@ static const struct piix_map_db *piix_map_db_table[] = { ...@@ -441,7 +444,7 @@ static const struct piix_map_db *piix_map_db_table[] = {
}; };
static struct ata_port_info piix_port_info[] = { static struct ata_port_info piix_port_info[] = {
/* piix_pata_33: 0: PIIX3 or 4 at 33MHz */ /* piix_pata_33: 0: PIIX4 at 33MHz */
{ {
.sht = &piix_sht, .sht = &piix_sht,
.flags = PIIX_PATA_FLAGS, .flags = PIIX_PATA_FLAGS,
...@@ -543,6 +546,14 @@ static struct ata_port_info piix_port_info[] = { ...@@ -543,6 +546,14 @@ static struct ata_port_info piix_port_info[] = {
.port_ops = &piix_sata_ops, .port_ops = &piix_sata_ops,
}, },
/* piix_pata_mwdma: 10: PIIX3 MWDMA only */
{
.sht = &piix_sht,
.flags = PIIX_PATA_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.mwdma_mask = 0x06, /* mwdma1-2 ?? CHECK 0 should be ok but slow */
.port_ops = &piix_pata_ops,
},
}; };
static struct pci_bits piix_enable_bits[] = { static struct pci_bits piix_enable_bits[] = {
...@@ -787,7 +798,8 @@ static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, i ...@@ -787,7 +798,8 @@ static void do_pata_set_dmamode (struct ata_port *ap, struct ata_device *adev, i
{ 2, 3 }, }; { 2, 3 }, };
pci_read_config_word(dev, master_port, &master_data); pci_read_config_word(dev, master_port, &master_data);
pci_read_config_byte(dev, 0x48, &udma_enable); if (ap->udma_mask)
pci_read_config_byte(dev, 0x48, &udma_enable);
if (speed >= XFER_UDMA_0) { if (speed >= XFER_UDMA_0) {
unsigned int udma = adev->dma_mode - XFER_UDMA_0; unsigned int udma = adev->dma_mode - XFER_UDMA_0;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册