提交 c39aedaf 编写于 作者: G Guenter Roeck 提交者: Jean Delvare

hwmon: (w83627ehf) Add support for W83667HG-B

Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
上级 da2e0255
......@@ -20,6 +20,10 @@ Supported chips:
Prefix: 'w83667hg'
Addresses scanned: ISA address retrieved from Super I/O registers
Datasheet: not available
* Winbond W83667HG-B
Prefix: 'w83667hg'
Addresses scanned: ISA address retrieved from Super I/O registers
Datasheet: Available from Nuvoton upon request
Authors:
Jean Delvare <khali@linux-fr.org>
......@@ -32,8 +36,8 @@ Description
-----------
This driver implements support for the Winbond W83627EHF, W83627EHG,
W83627DHG, W83627DHG-P and W83667HG super I/O chips. We will refer to them
collectively as Winbond chips.
W83627DHG, W83627DHG-P, W83667HG and W83667HG-B super I/O chips.
We will refer to them collectively as Winbond chips.
The chips implement three temperature sensors, five fan rotation
speed sensors, ten analog voltage sensors (only nine for the 627DHG), one
......@@ -68,14 +72,15 @@ follows:
temp1 -> pwm1
temp2 -> pwm2
temp3 -> pwm3
prog -> pwm4 (not on 667HG; the programmable setting is not supported by
the driver)
prog -> pwm4 (not on 667HG and 667HG-B; the programmable setting is not
supported by the driver)
/sys files
----------
name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG,
it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg"
it is set to "w83627ehf", for the W83627DHG it is set to "w83627dhg",
and for the W83667HG it is set to "w83667hg".
pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
0 (stop) to 255 (full)
......
......@@ -39,6 +39,7 @@
w83627dhg 9 5 4 3 0xa020 0xc1 0x5ca3
w83627dhg-p 9 5 4 3 0xb070 0xc1 0x5ca3
w83667hg 9 5 3 3 0xa510 0xc1 0x5ca3
w83667hg-b 9 5 3 3 0xb350 0xc1 0x5ca3
*/
#include <linux/module.h>
......@@ -55,7 +56,7 @@
#include <linux/io.h>
#include "lm75.h"
enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg };
enum kinds { w83627ehf, w83627dhg, w83627dhg_p, w83667hg, w83667hg_b };
/* used to set data->name = w83627ehf_device_names[data->sio_kind] */
static const char * w83627ehf_device_names[] = {
......@@ -63,6 +64,7 @@ static const char * w83627ehf_device_names[] = {
"w83627dhg",
"w83627dhg",
"w83667hg",
"w83667hg",
};
static unsigned short force_id;
......@@ -91,6 +93,7 @@ MODULE_PARM_DESC(force_id, "Override the detected device ID");
#define SIO_W83627DHG_ID 0xa020
#define SIO_W83627DHG_P_ID 0xb070
#define SIO_W83667HG_ID 0xa510
#define SIO_W83667HG_B_ID 0xb350
#define SIO_ID_MASK 0xFFF0
static inline void
......@@ -201,8 +204,14 @@ static const u8 W83627EHF_REG_TOLERANCE[] = { 0x07, 0x07, 0x14, 0x62 };
static const u8 W83627EHF_REG_FAN_START_OUTPUT[] = { 0x0a, 0x0b, 0x16, 0x65 };
static const u8 W83627EHF_REG_FAN_STOP_OUTPUT[] = { 0x08, 0x09, 0x15, 0x64 };
static const u8 W83627EHF_REG_FAN_STOP_TIME[] = { 0x0c, 0x0d, 0x17, 0x66 };
static const u8 W83627EHF_REG_FAN_MAX_OUTPUT[] = { 0xff, 0x67, 0xff, 0x69 };
static const u8 W83627EHF_REG_FAN_STEP_OUTPUT[] = { 0xff, 0x68, 0xff, 0x6a };
static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_COMMON[]
= { 0xff, 0x67, 0xff, 0x69 };
static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_COMMON[]
= { 0xff, 0x68, 0xff, 0x6a };
static const u8 W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B[] = { 0x67, 0x69, 0x6b };
static const u8 W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B[] = { 0x68, 0x6a, 0x6c };
/*
* Conversions
......@@ -1382,10 +1391,11 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
/* 627EHG and 627EHF have 10 voltage inputs; 627DHG and 667HG have 9 */
data->in_num = (sio_data->kind == w83627ehf) ? 10 : 9;
/* 667HG has 3 pwms */
data->pwm_num = (sio_data->kind == w83667hg) ? 3 : 4;
data->pwm_num = (sio_data->kind == w83667hg
|| sio_data->kind == w83667hg_b) ? 3 : 4;
/* Check temp3 configuration bit for 667HG */
if (sio_data->kind == w83667hg) {
if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
data->temp3_disable = w83627ehf_read_value(data,
W83627EHF_REG_TEMP_CONFIG[1]) & 0x01;
data->in6_skip = !data->temp3_disable;
......@@ -1393,8 +1403,17 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
data->REG_FAN_START_OUTPUT = W83627EHF_REG_FAN_START_OUTPUT;
data->REG_FAN_STOP_OUTPUT = W83627EHF_REG_FAN_STOP_OUTPUT;
data->REG_FAN_MAX_OUTPUT = W83627EHF_REG_FAN_MAX_OUTPUT;
data->REG_FAN_STEP_OUTPUT = W83627EHF_REG_FAN_STEP_OUTPUT;
if (sio_data->kind == w83667hg_b) {
data->REG_FAN_MAX_OUTPUT =
W83627EHF_REG_FAN_MAX_OUTPUT_W83667_B;
data->REG_FAN_STEP_OUTPUT =
W83627EHF_REG_FAN_STEP_OUTPUT_W83667_B;
} else {
data->REG_FAN_MAX_OUTPUT =
W83627EHF_REG_FAN_MAX_OUTPUT_COMMON;
data->REG_FAN_STEP_OUTPUT =
W83627EHF_REG_FAN_STEP_OUTPUT_COMMON;
}
/* Initialize the chip */
w83627ehf_init_device(data);
......@@ -1402,7 +1421,7 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
data->vrm = vid_which_vrm();
superio_enter(sio_data->sioreg);
/* Read VID value */
if (sio_data->kind == w83667hg) {
if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
/* W83667HG has different pins for VID input and output, so
we can get the VID input values directly at logical device D
0xe3. */
......@@ -1453,7 +1472,7 @@ static int __devinit w83627ehf_probe(struct platform_device *pdev)
}
/* fan4 and fan5 share some pins with the GPIO and serial flash */
if (sio_data->kind == w83667hg) {
if (sio_data->kind == w83667hg || sio_data->kind == w83667hg_b) {
fan5pin = superio_inb(sio_data->sioreg, 0x27) & 0x20;
fan4pin = superio_inb(sio_data->sioreg, 0x27) & 0x40;
} else {
......@@ -1609,6 +1628,7 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
static const char __initdata sio_name_W83627DHG[] = "W83627DHG";
static const char __initdata sio_name_W83627DHG_P[] = "W83627DHG-P";
static const char __initdata sio_name_W83667HG[] = "W83667HG";
static const char __initdata sio_name_W83667HG_B[] = "W83667HG-B";
u16 val;
const char *sio_name;
......@@ -1641,6 +1661,10 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr,
sio_data->kind = w83667hg;
sio_name = sio_name_W83667HG;
break;
case SIO_W83667HG_B_ID:
sio_data->kind = w83667hg_b;
sio_name = sio_name_W83667HG_B;
break;
default:
if (val != 0xffff)
pr_debug(DRVNAME ": unsupported chip ID: 0x%04x\n",
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册