提交 afa153fd 编写于 作者: L Linus Torvalds

Merge git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  ide/Kconfig: mark ide-scsi as deprecated
  ide-disk: remove stale init_idedisk_capacity() documentation
  palm_bk3710: improve IDE registration
  ide: fix hwif_to_node()
  IDE: palm_bk3710: fix compile warning for unused variable
  IDE: compile fix for sff_dma_ops
......@@ -242,7 +242,7 @@ config BLK_DEV_IDEFLOPPY
module will be called ide-floppy.
config BLK_DEV_IDESCSI
tristate "SCSI emulation support"
tristate "SCSI emulation support (DEPRECATED)"
depends on SCSI
select IDE_ATAPI
---help---
......@@ -255,20 +255,6 @@ config BLK_DEV_IDESCSI
and will allow you to use a SCSI device driver instead of a native
ATAPI driver.
This is useful if you have an ATAPI device for which no native
driver has been written (for example, an ATAPI PD-CD drive);
you can then use this emulation together with an appropriate SCSI
device driver. In order to do this, say Y here and to "SCSI support"
and "SCSI generic support", below. You must then provide the kernel
command line "hdx=ide-scsi" (try "man bootparam" or see the
documentation of your boot loader (lilo or loadlin) about how to
pass options to the kernel at boot time) for devices if you want the
native EIDE sub-drivers to skip over the native support, so that
this SCSI emulation can be used instead.
Note that this option does NOT allow you to attach SCSI devices to a
box that doesn't have a SCSI host adapter installed.
If both this SCSI emulation and native ATAPI support are compiled
into the kernel, the native support will be used.
......
......@@ -343,11 +343,10 @@ static struct ide_port_info __devinitdata palm_bk3710_port_info = {
.mwdma_mask = ATA_MWDMA2,
};
static int __devinit palm_bk3710_probe(struct platform_device *pdev)
static int __init palm_bk3710_probe(struct platform_device *pdev)
{
struct clk *clk;
struct resource *mem, *irq;
struct ide_host *host;
unsigned long base, rate;
int i, rc;
hw_regs_t hw, *hws[] = { &hw, NULL, NULL, NULL };
......@@ -390,6 +389,7 @@ static int __devinit palm_bk3710_probe(struct platform_device *pdev)
hw.io_ports_array[i] = base + IDE_PALM_ATA_PRI_REG_OFFSET + i;
hw.io_ports.ctl_addr = base + IDE_PALM_ATA_PRI_CTL_OFFSET;
hw.irq = irq->start;
hw.dev = &pdev->dev;
hw.chipset = ide_palm3710;
palm_bk3710_port_info.udma_mask = rate < 100000000 ? ATA_UDMA4 :
......@@ -413,13 +413,11 @@ static struct platform_driver platform_bk_driver = {
.name = "palm_bk3710",
.owner = THIS_MODULE,
},
.probe = palm_bk3710_probe,
.remove = NULL,
};
static int __init palm_bk3710_init(void)
{
return platform_driver_register(&platform_bk_driver);
return platform_driver_probe(&platform_bk_driver, palm_bk3710_probe);
}
module_init(palm_bk3710_init);
......
......@@ -445,20 +445,6 @@ static void idedisk_check_hpa(ide_drive_t *drive)
}
}
/*
* Compute drive->capacity, the full capacity of the drive
* Called with drive->id != NULL.
*
* To compute capacity, this uses either of
*
* 1. CHS value set by user (whatever user sets will be trusted)
* 2. LBA value from target drive (require new ATA feature)
* 3. LBA value from system BIOS (new one is OK, old one may break)
* 4. CHS value from system BIOS (traditional style)
*
* in above order (i.e., if value of higher priority is available,
* reset will be ignored).
*/
static void init_idedisk_capacity(ide_drive_t *drive)
{
struct hd_driveid *id = drive->id;
......
......@@ -1111,7 +1111,6 @@ void ide_setup_pci_noise(struct pci_dev *, const struct ide_port_info *);
#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
int ide_pci_set_master(struct pci_dev *, const char *);
unsigned long ide_pci_dma_base(ide_hwif_t *, const struct ide_port_info *);
extern const struct ide_dma_ops sff_dma_ops;
int ide_pci_check_simplex(ide_hwif_t *, const struct ide_port_info *);
int ide_hwif_setup_dma(ide_hwif_t *, const struct ide_port_info *);
#else
......@@ -1275,6 +1274,7 @@ extern int __ide_dma_end(ide_drive_t *);
int ide_dma_test_irq(ide_drive_t *);
extern void ide_dma_lost_irq(ide_drive_t *);
extern void ide_dma_timeout(ide_drive_t *);
extern const struct ide_dma_ops sff_dma_ops;
#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
#else
......@@ -1448,8 +1448,7 @@ static inline void ide_dump_identify(u8 *id)
static inline int hwif_to_node(ide_hwif_t *hwif)
{
struct pci_dev *dev = to_pci_dev(hwif->dev);
return hwif->dev ? pcibus_to_node(dev->bus) : -1;
return hwif->dev ? dev_to_node(hwif->dev) : -1;
}
static inline ide_drive_t *ide_get_paired_drive(ide_drive_t *drive)
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册