提交 a77df5cd 编写于 作者: L Linus Torvalds

Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: ATA_EHI_LPM should be ATA_EH_LPM
  pata_sil680: only enable MMIO on Cell blades
......@@ -972,7 +972,7 @@ static void ata_dev_disable_pm(struct ata_device *dev)
void ata_lpm_schedule(struct ata_port *ap, enum link_pm policy)
{
ap->pm_policy = policy;
ap->link.eh_info.action |= ATA_EHI_LPM;
ap->link.eh_info.action |= ATA_EH_LPM;
ap->link.eh_info.flags |= ATA_EHI_NO_AUTOPSY;
ata_port_schedule_eh(ap);
}
......
......@@ -2748,7 +2748,7 @@ int ata_eh_recover(struct ata_port *ap, ata_prereset_fn_t prereset,
ehc->i.flags &= ~ATA_EHI_SETMODE;
}
if (ehc->i.action & ATA_EHI_LPM)
if (ehc->i.action & ATA_EH_LPM)
ata_link_for_each_dev(dev, link)
ata_dev_enable_pm(dev, ap->pm_policy);
......
......@@ -269,7 +269,11 @@ static u8 sil680_init_chip(struct pci_dev *pdev, int *try_mmio)
dev_dbg(&pdev->dev, "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
*try_mmio = (tmpbyte & 1) || pci_resource_start(pdev, 5);
*try_mmio = 0;
#ifdef CONFIG_PPC
if (machine_is(cell))
*try_mmio = (tmpbyte & 1) || pci_resource_start(pdev, 5);
#endif
switch(tmpbyte & 0x30) {
case 0x00:
......
......@@ -295,6 +295,7 @@ enum {
ATA_EH_SOFTRESET = (1 << 1),
ATA_EH_HARDRESET = (1 << 2),
ATA_EH_ENABLE_LINK = (1 << 3),
ATA_EH_LPM = (1 << 4), /* link power management action */
ATA_EH_RESET_MASK = ATA_EH_SOFTRESET | ATA_EH_HARDRESET,
ATA_EH_PERDEV_MASK = ATA_EH_REVALIDATE,
......@@ -304,7 +305,6 @@ enum {
ATA_EHI_RESUME_LINK = (1 << 1), /* resume link (reset modifier) */
ATA_EHI_NO_AUTOPSY = (1 << 2), /* no autopsy */
ATA_EHI_QUIET = (1 << 3), /* be quiet */
ATA_EHI_LPM = (1 << 4), /* link power management action */
ATA_EHI_DID_SOFTRESET = (1 << 16), /* already soft-reset this port */
ATA_EHI_DID_HARDRESET = (1 << 17), /* already soft-reset this port */
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册