提交 a1f1c7ef 编写于 作者: S Shawn Guo 提交者: Arnd Bergmann

arm/imx6q: add suspend/resume support

It adds suspend/resume support for imx6q.
Signed-off-by: NAnson Huang <b20788@freescale.com>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
上级 13eed989
......@@ -70,4 +70,4 @@ AFLAGS_head-v7.o :=-Wa,-march=armv7-a
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o
obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o pm-imx6q.o
......@@ -12,6 +12,7 @@
#include <linux/linkage.h>
#include <linux/init.h>
#include <asm/asm-offsets.h>
#include <asm/hardware/cache-l2x0.h>
.section ".text.head", "ax"
......@@ -69,3 +70,30 @@ ENTRY(v7_secondary_startup)
b secondary_startup
ENDPROC(v7_secondary_startup)
#endif
/*
* The following code is located into the .data section. This is to
* allow phys_l2x0_saved_regs to be accessed with a relative load
* as we are running on physical address here.
*/
.data
.align
.macro pl310_resume
ldr r2, phys_l2x0_saved_regs
ldr r0, [r2, #L2X0_R_PHY_BASE] @ get physical base of l2x0
ldr r1, [r2, #L2X0_R_AUX_CTRL] @ get aux_ctrl value
str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl
mov r1, #0x1
str r1, [r0, #L2X0_CTRL] @ re-enable L2
.endm
ENTRY(v7_cpu_resume)
bl v7_invalidate_l1
pl310_resume
b cpu_resume
ENDPROC(v7_cpu_resume)
.globl phys_l2x0_saved_regs
phys_l2x0_saved_regs:
.long 0
/*
* Copyright 2011 Freescale Semiconductor, Inc.
* Copyright 2011 Linaro Ltd.
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/init.h>
#include <linux/io.h>
#include <linux/of.h>
#include <linux/suspend.h>
#include <asm/cacheflush.h>
#include <asm/proc-fns.h>
#include <asm/suspend.h>
#include <asm/hardware/cache-l2x0.h>
#include <mach/common.h>
#include <mach/hardware.h>
extern unsigned long phys_l2x0_saved_regs;
static int imx6q_suspend_finish(unsigned long val)
{
cpu_do_idle();
return 0;
}
static int imx6q_pm_enter(suspend_state_t state)
{
switch (state) {
case PM_SUSPEND_MEM:
imx6q_set_lpm(STOP_POWER_OFF);
imx_gpc_pre_suspend();
imx_set_cpu_jump(0, v7_cpu_resume);
/* Zzz ... */
cpu_suspend(0, imx6q_suspend_finish);
imx_smp_prepare();
imx_gpc_post_resume();
break;
default:
return -EINVAL;
}
return 0;
}
static const struct platform_suspend_ops imx6q_pm_ops = {
.enter = imx6q_pm_enter,
.valid = suspend_valid_only_mem,
};
void __init imx6q_pm_init(void)
{
/*
* The l2x0 core code provides an infrastucture to save and restore
* l2x0 registers across suspend/resume cycle. But because imx6q
* retains L2 content during suspend and needs to resume L2 before
* MMU is enabled, it can only utilize register saving support and
* have to take care of restoring on its own. So we save physical
* address of the data structure used by l2x0 core to save registers,
* and later restore the necessary ones in imx6q resume entry.
*/
phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
suspend_set_ops(&imx6q_pm_ops);
}
......@@ -13,6 +13,7 @@
struct platform_device;
struct clk;
enum mxc_cpu_pwr_mode;
extern void mx1_map_io(void);
extern void mx21_map_io(void);
......@@ -107,14 +108,22 @@ extern void imx_lluart_map_io(void);
#else
static inline void imx_lluart_map_io(void) {}
#endif
extern void v7_cpu_resume(void);
extern u32 *pl310_get_save_ptr(void);
#ifdef CONFIG_SMP
extern void v7_secondary_startup(void);
extern void imx_scu_map_io(void);
extern void imx_smp_prepare(void);
#else
static inline void imx_scu_map_io(void) {}
static inline void imx_smp_prepare(void) {}
#endif
extern void imx_enable_cpu(int cpu, bool enable);
extern void imx_set_cpu_jump(int cpu, void *jump_addr);
extern void imx_src_init(void);
extern void imx_gpc_init(void);
extern void imx_gpc_pre_suspend(void);
extern void imx_gpc_post_resume(void);
extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
extern void imx6q_pm_init(void);
#endif
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册