提交 8a1417de 编写于 作者: A Andrew Isaacson 提交者: Ralf Baechle

BCM1480 HT support

    
PCI support code for PLX 7250 PCI-X tunnel on BCM91480B BigSur board.
Signed-Off-By: NAndy Isaacson <adi@broadcom.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
上级 dc41f94f
......@@ -554,6 +554,7 @@ config SIBYTE_BIGSUR
select SWAP_IO_SPACE
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
select PCI_DOMAINS
config SIBYTE_SWARM
bool "Support for Sibyte BCM91250A-SWARM"
......
......@@ -46,7 +46,7 @@ obj-$(CONFIG_PMC_YOSEMITE) += fixup-yosemite.o ops-titan.o ops-titan-ht.o \
obj-$(CONFIG_SGI_IP27) += pci-ip27.o
obj-$(CONFIG_SGI_IP32) += fixup-ip32.o ops-mace.o pci-ip32.o
obj-$(CONFIG_SIBYTE_SB1250) += fixup-sb1250.o pci-sb1250.o
obj-$(CONFIG_SIBYTE_BCM1x80) += pci-bcm1480.o
obj-$(CONFIG_SIBYTE_BCM1x80) += pci-bcm1480.o pci-bcm1480ht.o
obj-$(CONFIG_SNI_RM200_PCI) += fixup-sni.o ops-sni.o
obj-$(CONFIG_TANBAC_TB0219) += fixup-tb0219.o
obj-$(CONFIG_TANBAC_TB0226) += fixup-tb0226.o
......
......@@ -56,13 +56,11 @@
static void *cfg_space;
#define PCI_BUS_ENABLED 1
#define LDT_BUS_ENABLED 2
#define PCI_DEVICE_MODE 4
#define PCI_DEVICE_MODE 2
static int bcm1480_bus_status = 0;
#define PCI_BRIDGE_DEVICE 0
#define LDT_BRIDGE_DEVICE 1
/*
* Read/write 32-bit values in config space.
......@@ -95,10 +93,13 @@ int pcibios_plat_dev_init(struct pci_dev *dev)
*/
static int bcm1480_pci_can_access(struct pci_bus *bus, int devfn)
{
u32 devno;
if (!(bcm1480_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
return 0;
if (bus->number == 0) {
devno = PCI_SLOT(devfn);
if (bcm1480_bus_status & PCI_DEVICE_MODE)
return 0;
else
......@@ -175,15 +176,15 @@ struct pci_ops bcm1480_pci_ops = {
static struct resource bcm1480_mem_resource = {
.name = "BCM1480 PCI MEM",
.start = 0x40000000UL,
.end = 0x5fffffffUL,
.start = 0x30000000UL,
.end = 0x3fffffffUL,
.flags = IORESOURCE_MEM,
};
static struct resource bcm1480_io_resource = {
.name = "BCM1480 PCI I/O",
.start = 0x00000000UL,
.end = 0x01ffffffUL,
.start = 0x2c000000UL,
.end = 0x2dffffffUL,
.flags = IORESOURCE_IO,
};
......@@ -207,9 +208,9 @@ static int __init bcm1480_pcibios_init(void)
PCIBIOS_MIN_IO = 0x00008000UL;
PCIBIOS_MIN_MEM = 0x01000000UL;
/* Set I/O resource limits. */
ioport_resource.end = 0x01ffffffUL; /* 32MB accessible by bcm1480 */
iomem_resource.end = 0xffffffffUL; /* no HT support yet */
/* Set I/O resource limits. - unlimited for now to accomodate HT */
ioport_resource.end = 0xffffffffUL;
iomem_resource.end = 0xffffffffUL;
cfg_space = ioremap(A_BCM1480_PHYS_PCI_CFG_MATCH_BITS, 16*1024*1024);
......
/*
* Copyright (C) 2001,2002,2005 Broadcom Corporation
* Copyright (C) 2004 by Ralf Baechle (ralf@linux-mips.org)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*/
/*
* BCM1480/1455-specific HT support (looking like PCI)
*
* This module provides the glue between Linux's PCI subsystem
* and the hardware. We basically provide glue for accessing
* configuration space, and set up the translation for I/O
* space accesses.
*
* To access configuration space, we use ioremap. In the 32-bit
* kernel, this consumes either 4 or 8 page table pages, and 16MB of
* kernel mapped memory. Hopefully neither of these should be a huge
* problem.
*
*/
#include <linux/config.h>
#include <linux/types.h>
#include <linux/pci.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/tty.h>
#include <asm/sibyte/bcm1480_regs.h>
#include <asm/sibyte/bcm1480_scd.h>
#include <asm/sibyte/board.h>
#include <asm/io.h>
/*
* Macros for calculating offsets into config space given a device
* structure or dev/fun/reg
*/
#define CFGOFFSET(bus,devfn,where) (((bus)<<16)+((devfn)<<8)+(where))
#define CFGADDR(bus,devfn,where) CFGOFFSET((bus)->number,(devfn),where)
static void *ht_cfg_space;
#define PCI_BUS_ENABLED 1
#define PCI_DEVICE_MODE 2
static int bcm1480ht_bus_status = 0;
#define PCI_BRIDGE_DEVICE 0
#define HT_BRIDGE_DEVICE 1
/*
* HT's level-sensitive interrupts require EOI, which is generated
* through a 4MB memory-mapped region
*/
unsigned long ht_eoi_space;
/*
* Read/write 32-bit values in config space.
*/
static inline u32 READCFG32(u32 addr)
{
return *(u32 *)(ht_cfg_space + (addr&~3));
}
static inline void WRITECFG32(u32 addr, u32 data)
{
*(u32 *)(ht_cfg_space + (addr & ~3)) = data;
}
/*
* Some checks before doing config cycles:
* In PCI Device Mode, hide everything on bus 0 except the LDT host
* bridge. Otherwise, access is controlled by bridge MasterEn bits.
*/
static int bcm1480ht_can_access(struct pci_bus *bus, int devfn)
{
u32 devno;
if (!(bcm1480ht_bus_status & (PCI_BUS_ENABLED | PCI_DEVICE_MODE)))
return 0;
if (bus->number == 0) {
devno = PCI_SLOT(devfn);
if (bcm1480ht_bus_status & PCI_DEVICE_MODE)
return 0;
}
return 1;
}
/*
* Read/write access functions for various sizes of values
* in config space. Return all 1's for disallowed accesses
* for a kludgy but adequate simulation of master aborts.
*/
static int bcm1480ht_pcibios_read(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 * val)
{
u32 data = 0;
if ((size == 2) && (where & 1))
return PCIBIOS_BAD_REGISTER_NUMBER;
else if ((size == 4) && (where & 3))
return PCIBIOS_BAD_REGISTER_NUMBER;
if (bcm1480ht_can_access(bus, devfn))
data = READCFG32(CFGADDR(bus, devfn, where));
else
data = 0xFFFFFFFF;
if (size == 1)
*val = (data >> ((where & 3) << 3)) & 0xff;
else if (size == 2)
*val = (data >> ((where & 3) << 3)) & 0xffff;
else
*val = data;
return PCIBIOS_SUCCESSFUL;
}
static int bcm1480ht_pcibios_write(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 val)
{
u32 cfgaddr = CFGADDR(bus, devfn, where);
u32 data = 0;
if ((size == 2) && (where & 1))
return PCIBIOS_BAD_REGISTER_NUMBER;
else if ((size == 4) && (where & 3))
return PCIBIOS_BAD_REGISTER_NUMBER;
if (!bcm1480ht_can_access(bus, devfn))
return PCIBIOS_BAD_REGISTER_NUMBER;
data = READCFG32(cfgaddr);
if (size == 1)
data = (data & ~(0xff << ((where & 3) << 3))) |
(val << ((where & 3) << 3));
else if (size == 2)
data = (data & ~(0xffff << ((where & 3) << 3))) |
(val << ((where & 3) << 3));
else
data = val;
WRITECFG32(cfgaddr, data);
return PCIBIOS_SUCCESSFUL;
}
static int bcm1480ht_pcibios_get_busno(void)
{
return 0;
}
struct pci_ops bcm1480ht_pci_ops = {
.read = bcm1480ht_pcibios_read,
.write = bcm1480ht_pcibios_write,
};
static struct resource bcm1480ht_mem_resource = {
.name = "BCM1480 HT MEM",
.start = 0x40000000UL,
.end = 0x5fffffffUL,
.flags = IORESOURCE_MEM,
};
static struct resource bcm1480ht_io_resource = {
.name = "BCM1480 HT I/O",
.start = 0x00000000UL,
.end = 0x01ffffffUL,
.flags = IORESOURCE_IO,
};
struct pci_controller bcm1480ht_controller = {
.pci_ops = &bcm1480ht_pci_ops,
.mem_resource = &bcm1480ht_mem_resource,
.io_resource = &bcm1480ht_io_resource,
.index = 1,
.get_busno = bcm1480ht_pcibios_get_busno,
};
static int __init bcm1480ht_pcibios_init(void)
{
uint32_t cmdreg;
ht_cfg_space = ioremap(A_BCM1480_PHYS_HT_CFG_MATCH_BITS, 16*1024*1024);
/*
* See if the PCI bus has been configured by the firmware.
*/
cmdreg = READCFG32(CFGOFFSET(0, PCI_DEVFN(PCI_BRIDGE_DEVICE, 0),
PCI_COMMAND));
if (!(cmdreg & PCI_COMMAND_MASTER)) {
printk("HT: Skipping HT probe. Bus is not initialized.\n");
iounmap(ht_cfg_space);
return 1; /* XXX */
}
bcm1480ht_bus_status |= PCI_BUS_ENABLED;
ht_eoi_space = (unsigned long)
ioremap(A_BCM1480_PHYS_HT_SPECIAL_MATCH_BYTES,
4 * 1024 * 1024);
register_pci_controller(&bcm1480ht_controller);
return 0;
}
arch_initcall(bcm1480ht_pcibios_init);
......@@ -127,15 +127,20 @@ static int __init pcibios_init(void)
if (!hose->iommu)
PCI_DMA_BUS_IS_PHYS = 1;
if (hose->get_busno && pci_probe_only)
next_busno = (*hose->get_busno)();
bus = pci_scan_bus(next_busno, hose->pci_ops, hose);
hose->bus = bus;
hose->need_domain_info = need_domain_info;
next_busno = bus->subordinate + 1;
/* Don't allow 8-bit bus number overflow inside the hose -
reserve some space for bridges. */
if (next_busno > 224) {
next_busno = 0;
need_domain_info = 1;
if (bus) {
next_busno = bus->subordinate + 1;
/* Don't allow 8-bit bus number overflow inside the hose -
reserve some space for bridges. */
if (next_busno > 224) {
next_busno = 0;
need_domain_info = 1;
}
}
continue;
......
......@@ -40,6 +40,11 @@ struct pci_controller {
unsigned int need_domain_info;
int iommu;
/* Optional access methods for reading/writing the bus number
of the PCI controller */
int (*get_busno)(void);
void (*set_busno)(int busno);
};
/*
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册