提交 7e72aad4 编写于 作者: M Michael Chan 提交者: David S. Miller

[TG3]: add variable buffer size for standard ring

Add a new rx_pkt_buf_sz to the tg3 structure to support variable buffer
sizes on the standard ring.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
上级 0f893dc6
......@@ -2621,7 +2621,7 @@ static int tg3_alloc_rx_skb(struct tg3 *tp, u32 opaque_key,
map = &tp->rx_std_buffers[dest_idx];
if (src_idx >= 0)
src_map = &tp->rx_std_buffers[src_idx];
skb_size = RX_PKT_BUF_SZ;
skb_size = tp->rx_pkt_buf_sz;
break;
case RXD_OPAQUE_RING_JUMBO:
......@@ -3500,7 +3500,7 @@ static void tg3_free_rings(struct tg3 *tp)
continue;
pci_unmap_single(tp->pdev,
pci_unmap_addr(rxp, mapping),
RX_PKT_BUF_SZ - tp->rx_offset,
tp->rx_pkt_buf_sz - tp->rx_offset,
PCI_DMA_FROMDEVICE);
dev_kfree_skb_any(rxp->skb);
rxp->skb = NULL;
......@@ -3573,6 +3573,11 @@ static void tg3_init_rings(struct tg3 *tp)
memset(tp->rx_rcb, 0, TG3_RX_RCB_RING_BYTES(tp));
memset(tp->tx_ring, 0, TG3_TX_RING_BYTES);
tp->rx_pkt_buf_sz = RX_PKT_BUF_SZ;
if ((GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780) &&
(tp->dev->mtu > ETH_DATA_LEN))
tp->rx_pkt_buf_sz = RX_JUMBO_PKT_BUF_SZ;
/* Initialize invariants of the rings, we only set this
* stuff once. This works because the card does not
* write into the rx buffer posting rings.
......@@ -3581,7 +3586,7 @@ static void tg3_init_rings(struct tg3 *tp)
struct tg3_rx_buffer_desc *rxd;
rxd = &tp->rx_std[i];
rxd->idx_len = (RX_PKT_BUF_SZ - tp->rx_offset - 64)
rxd->idx_len = (tp->rx_pkt_buf_sz - tp->rx_offset - 64)
<< RXD_LEN_SHIFT;
rxd->type_flags = (RXD_FLAG_END << RXD_FLAGS_SHIFT);
rxd->opaque = (RXD_OPAQUE_RING_STD |
......
......@@ -2088,6 +2088,8 @@ struct tg3 {
struct tg3_rx_buffer_desc *rx_rcb;
dma_addr_t rx_rcb_mapping;
u32 rx_pkt_buf_sz;
/* begin "everything else" cacheline(s) section */
struct net_device_stats net_stats;
struct net_device_stats net_stats_prev;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册