提交 562a7480 编写于 作者: J Johannes Berg 提交者: John W. Linville

nl80211: advertise device AP SME

Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
上级 21fc7560
......@@ -1548,7 +1548,8 @@ static int ath6kl_init(struct net_device *dev)
ar->conf_flags = ATH6KL_CONF_IGNORE_ERP_BARKER |
ATH6KL_CONF_ENABLE_11N | ATH6KL_CONF_ENABLE_TX_BURST;
ar->wdev->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM;
ar->wdev->wiphy->flags |= WIPHY_FLAG_SUPPORTS_FW_ROAM |
WIPHY_FLAG_HAVE_AP_SME;
status = ath6kl_target_config_wlan_params(ar);
if (!status)
......
......@@ -1121,6 +1121,11 @@ enum nl80211_commands {
* %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
* used for asking the driver to perform a TDLS operation.
*
* @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices
* that have AP support to indicate that they have the AP SME integrated
* with support for the features listed in this attribute, see
* &enum nl80211_ap_sme_features.
*
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
......@@ -1349,6 +1354,8 @@ enum nl80211_attrs {
NL80211_ATTR_TDLS_SUPPORT,
NL80211_ATTR_TDLS_EXTERNAL_SETUP,
NL80211_ATTR_DEVICE_AP_SME,
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
......@@ -2662,4 +2669,12 @@ enum nl80211_tdls_operation {
NL80211_TDLS_DISABLE_LINK,
};
/*
* enum nl80211_ap_sme_features - device-integrated AP features
* Reserved for future use, no bits are defined in
* NL80211_ATTR_DEVICE_AP_SME yet.
enum nl80211_ap_sme_features {
};
*/
#endif /* __LINUX_NL80211_H */
......@@ -1679,6 +1679,7 @@ struct cfg80211_ops {
* teardown packets should be sent through the @NL80211_CMD_TDLS_MGMT
* command. When this flag is not set, @NL80211_CMD_TDLS_OPER should be
* used for asking the driver/firmware to perform a TDLS operation.
* @WIPHY_FLAG_HAVE_AP_SME: device integrates AP SME
*/
enum wiphy_flags {
WIPHY_FLAG_CUSTOM_REGULATORY = BIT(0),
......@@ -1697,6 +1698,7 @@ enum wiphy_flags {
WIPHY_FLAG_AP_UAPSD = BIT(14),
WIPHY_FLAG_SUPPORTS_TDLS = BIT(15),
WIPHY_FLAG_TDLS_EXTERNAL_SETUP = BIT(16),
WIPHY_FLAG_HAVE_AP_SME = BIT(17),
};
/**
......@@ -1907,6 +1909,8 @@ struct wiphy_wowlan_support {
* may request, if implemented.
*
* @wowlan: WoWLAN support information
*
* @ap_sme_capa: AP SME capabilities, flags from &enum nl80211_ap_sme_features.
*/
struct wiphy {
/* assign these fields before you register the wiphy */
......@@ -1930,6 +1934,8 @@ struct wiphy {
u32 flags;
u32 ap_sme_capa;
enum cfg80211_signal_type signal_type;
int bss_priv_size;
......
......@@ -492,6 +492,10 @@ int wiphy_register(struct wiphy *wiphy)
!(wiphy->wowlan.flags & WIPHY_WOWLAN_SUPPORTS_GTK_REKEY)))
return -EINVAL;
if (WARN_ON(wiphy->ap_sme_capa &&
!(wiphy->flags & WIPHY_FLAG_HAVE_AP_SME)))
return -EINVAL;
if (WARN_ON(wiphy->addresses && !wiphy->n_addresses))
return -EINVAL;
......
......@@ -1007,6 +1007,10 @@ static int nl80211_send_wiphy(struct sk_buff *msg, u32 pid, u32 seq, int flags,
if (nl80211_put_iface_combinations(&dev->wiphy, msg))
goto nla_put_failure;
if (dev->wiphy.flags & WIPHY_FLAG_HAVE_AP_SME)
NLA_PUT_U32(msg, NL80211_ATTR_DEVICE_AP_SME,
dev->wiphy.ap_sme_capa);
return genlmsg_end(msg, hdr);
nla_put_failure:
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册