提交 5195e509 编写于 作者: W Wolfram Sang 提交者: Jean Delvare

i2c: Move at24 to drivers/misc/eeprom

As drivers/i2c/chips is going to go away, move the driver to
drivers/misc/eeprom. Other eeprom drivers may be moved here later, too.
Update Kconfig text to specify this driver as I2C.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>
上级 a01064a9
......@@ -16,32 +16,6 @@ config DS1682
This driver can also be built as a module. If so, the module
will be called ds1682.
config AT24
tristate "EEPROMs from most vendors"
depends on SYSFS && EXPERIMENTAL
help
Enable this driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
If you use this with an SMBus adapter instead of an I2C adapter,
full functionality is not available. Only smaller devices are
supported (24c16 and below, max 4 kByte).
This driver can also be built as a module. If so, the module
will be called at24.
config SENSORS_EEPROM
tristate "EEPROM reader"
depends on EXPERIMENTAL
......
......@@ -11,7 +11,6 @@
#
obj-$(CONFIG_DS1682) += ds1682.o
obj-$(CONFIG_AT24) += at24.o
obj-$(CONFIG_SENSORS_EEPROM) += eeprom.o
obj-$(CONFIG_SENSORS_MAX6875) += max6875.o
obj-$(CONFIG_SENSORS_PCA9539) += pca9539.o
......
......@@ -231,5 +231,6 @@ config DELL_LAPTOP
laptops.
source "drivers/misc/c2port/Kconfig"
source "drivers/misc/eeprom/Kconfig"
endif # MISC_DEVICES
......@@ -20,3 +20,4 @@ obj-$(CONFIG_SGI_XP) += sgi-xp/
obj-$(CONFIG_SGI_GRU) += sgi-gru/
obj-$(CONFIG_HP_ILO) += hpilo.o
obj-$(CONFIG_C2PORT) += c2port/
obj-y += eeprom/
menu "EEPROM support"
config AT24
tristate "I2C EEPROMs from most vendors"
depends on I2C && SYSFS && EXPERIMENTAL
help
Enable this driver to get read/write support to most I2C EEPROMs,
after you configure the driver to know about each EEPROM on
your target board. Use these generic chip names, instead of
vendor-specific ones like at24c64 or 24lc02:
24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08,
24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024
Unless you like data loss puzzles, always be sure that any chip
you configure as a 24c32 (32 kbit) or larger is NOT really a
24c16 (16 kbit) or smaller, and vice versa. Marking the chip
as read-only won't help recover from this. Also, if your chip
has any software write-protect mechanism you may want to review the
code to make sure this driver won't turn it on by accident.
If you use this with an SMBus adapter instead of an I2C adapter,
full functionality is not available. Only smaller devices are
supported (24c16 and below, max 4 kByte).
This driver can also be built as a module. If so, the module
will be called at24.
endmenu
obj-$(CONFIG_AT24) += at24.o
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册