ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1

Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for
MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance
with the control module programming guide. This fixes a bug where if trying to
use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be
affected by a changing SDMMC1_VDDS.

Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever
SDMMC1_VDDS ramps up/down or changes for cell protection purposes.

MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore
they can operate independently.
Signed-off-by: NBryan Buckley <bryan.buckley@ti.com>
Acked-by: NKishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/hsmmc.c

@@ -137,8 +137,7 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot,
 	 */
 	reg = omap4_ctrl_pad_readl(control_pbias_offset);
 	reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
-		OMAP4_MMC1_PWRDNZ_MASK |
-		OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
+		OMAP4_MMC1_PWRDNZ_MASK);
 	omap4_ctrl_pad_writel(reg, control_pbias_offset);
 }
 
@@ -156,8 +155,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 		else
 			reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK;
 		reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
-			OMAP4_MMC1_PWRDNZ_MASK |
-			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
+			OMAP4_MMC1_PWRDNZ_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
 
 		timeout = jiffies + msecs_to_jiffies(5);
@@ -171,16 +169,14 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot,
 		if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) {
 			pr_err("Pbias Voltage is not same as LDO\n");
 			/* Caution : On VMODE_ERROR Power Down MMC IO */
-			reg &= ~(OMAP4_MMC1_PWRDNZ_MASK |
-				OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
+			reg &= ~(OMAP4_MMC1_PWRDNZ_MASK);
 			omap4_ctrl_pad_writel(reg, control_pbias_offset);
 		}
 	} else {
 		reg = omap4_ctrl_pad_readl(control_pbias_offset);
 		reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK |
 			OMAP4_MMC1_PWRDNZ_MASK |
-			OMAP4_MMC1_PBIASLITE_VMODE_MASK |
-			OMAP4_USBC1_ICUSB_PWRDNZ_MASK);
+			OMAP4_MMC1_PBIASLITE_VMODE_MASK);
 		omap4_ctrl_pad_writel(reg, control_pbias_offset);
 	}
 }