提交 2c01946c 编写于 作者: S Sukumar Ghorai 提交者: Tony Lindgren

omap3 nand: cleanup virtual address usages

This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: NSukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
上级 948d38e7
......@@ -19,8 +19,6 @@
#include <plat/board.h>
#include <plat/gpmc.h>
#define WR_RD_PIN_MONITORING 0x00600000
static struct omap_nand_platform_data *gpmc_nand_data;
static struct resource gpmc_nand_resource = {
......@@ -71,10 +69,10 @@ static int omap2_nand_gpmc_retime(void)
t.wr_cycle = gpmc_round_ns_to_ticks(gpmc_nand_data->gpmc_t->wr_cycle);
/* Configure GPMC */
gpmc_cs_write_reg(gpmc_nand_data->cs, GPMC_CS_CONFIG1,
GPMC_CONFIG1_DEVICESIZE(gpmc_nand_data->devsize) |
GPMC_CONFIG1_DEVICETYPE_NAND);
gpmc_cs_configure(gpmc_nand_data->cs,
GPMC_CONFIG_DEV_SIZE, gpmc_nand_data->devsize);
gpmc_cs_configure(gpmc_nand_data->cs,
GPMC_CONFIG_DEV_TYPE, GPMC_DEVICETYPE_NAND);
err = gpmc_cs_set_timings(gpmc_nand_data->cs, &t);
if (err)
return err;
......@@ -82,27 +80,13 @@ static int omap2_nand_gpmc_retime(void)
return 0;
}
static int gpmc_nand_setup(void)
{
struct device *dev = &gpmc_nand_device.dev;
/* Set timings in GPMC */
if (omap2_nand_gpmc_retime() < 0) {
dev_err(dev, "Unable to set gpmc timings\n");
return -EINVAL;
}
return 0;
}
int __init gpmc_nand_init(struct omap_nand_platform_data *_nand_data)
{
unsigned int val;
int err = 0;
struct device *dev = &gpmc_nand_device.dev;
gpmc_nand_data = _nand_data;
gpmc_nand_data->nand_setup = gpmc_nand_setup;
gpmc_nand_data->nand_setup = omap2_nand_gpmc_retime;
gpmc_nand_device.dev.platform_data = gpmc_nand_data;
err = gpmc_cs_request(gpmc_nand_data->cs, NAND_IO_SIZE,
......@@ -112,19 +96,16 @@ int __init gpmc_nand_init(struct omap_nand_platform_data *_nand_data)
return err;
}
err = gpmc_nand_setup();
/* Set timings in GPMC */
err = omap2_nand_gpmc_retime();
if (err < 0) {
dev_err(dev, "NAND platform setup failed: %d\n", err);
dev_err(dev, "Unable to set gpmc timings: %d\n", err);
return err;
}
/* Enable RD PIN Monitoring Reg */
if (gpmc_nand_data->dev_ready) {
val = gpmc_cs_read_reg(gpmc_nand_data->cs,
GPMC_CS_CONFIG1);
val |= WR_RD_PIN_MONITORING;
gpmc_cs_write_reg(gpmc_nand_data->cs,
GPMC_CS_CONFIG1, val);
gpmc_cs_configure(gpmc_nand_data->cs, GPMC_CONFIG_RDY_BSY, 1);
}
err = platform_device_register(&gpmc_nand_device);
......
......@@ -641,15 +641,6 @@ int gpmc_prefetch_reset(int cs)
}
EXPORT_SYMBOL(gpmc_prefetch_reset);
/**
* gpmc_prefetch_status - reads prefetch status of engine
*/
int gpmc_prefetch_status(void)
{
return gpmc_read_reg(GPMC_PREFETCH_STATUS);
}
EXPORT_SYMBOL(gpmc_prefetch_status);
static void __init gpmc_mem_init(void)
{
int cs;
......
......@@ -25,9 +25,6 @@
#define GPMC_CS_NAND_ADDRESS 0x20
#define GPMC_CS_NAND_DATA 0x24
#define GPMC_CONFIG 0x50
#define GPMC_STATUS 0x54
/* Control Commands */
#define GPMC_CONFIG_RDY_BSY 0x00000001
#define GPMC_CONFIG_DEV_SIZE 0x00000002
......@@ -66,7 +63,6 @@
#define GPMC_CONFIG1_DEVICESIZE_16 GPMC_CONFIG1_DEVICESIZE(1)
#define GPMC_CONFIG1_DEVICETYPE(val) ((val & 3) << 10)
#define GPMC_CONFIG1_DEVICETYPE_NOR GPMC_CONFIG1_DEVICETYPE(0)
#define GPMC_CONFIG1_DEVICETYPE_NAND GPMC_CONFIG1_DEVICETYPE(2)
#define GPMC_CONFIG1_MUXADDDATA (1 << 9)
#define GPMC_CONFIG1_TIME_PARA_GRAN (1 << 4)
#define GPMC_CONFIG1_FCLK_DIV(val) (val & 3)
......@@ -136,7 +132,6 @@ extern int gpmc_cs_reserved(int cs);
extern int gpmc_prefetch_enable(int cs, int dma_mode,
unsigned int u32_count, int is_write);
extern int gpmc_prefetch_reset(int cs);
extern int gpmc_prefetch_status(void);
extern void omap3_gpmc_save_context(void);
extern void omap3_gpmc_restore_context(void);
extern void gpmc_init(void);
......
......@@ -21,13 +21,11 @@ struct omap_nand_platform_data {
int (*dev_ready)(struct omap_nand_platform_data *);
int dma_channel;
unsigned long phys_base;
void __iomem *gpmc_cs_baseaddr;
void __iomem *gpmc_baseaddr;
int devsize;
};
/* size (4 KiB) for IO mapping */
#define NAND_IO_SIZE SZ_4K
/* minimum size for IO mapping */
#define NAND_IO_SIZE 4
#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
extern int gpmc_nand_init(struct omap_nand_platform_data *d);
......
......@@ -7,6 +7,7 @@
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#define CONFIG_MTD_NAND_OMAP_HWECC
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
......@@ -23,20 +24,8 @@
#include <plat/gpmc.h>
#include <plat/nand.h>
#define GPMC_IRQ_STATUS 0x18
#define GPMC_ECC_CONFIG 0x1F4
#define GPMC_ECC_CONTROL 0x1F8
#define GPMC_ECC_SIZE_CONFIG 0x1FC
#define GPMC_ECC1_RESULT 0x200
#define DRIVER_NAME "omap2-nand"
#define NAND_WP_OFF 0
#define NAND_WP_BIT 0x00000010
#define GPMC_BUF_FULL 0x00000001
#define GPMC_BUF_EMPTY 0x00000000
#define NAND_Ecc_P1e (1 << 0)
#define NAND_Ecc_P2e (1 << 1)
#define NAND_Ecc_P4e (1 << 2)
......@@ -139,33 +128,10 @@ struct omap_nand_info {
int gpmc_cs;
unsigned long phys_base;
void __iomem *gpmc_cs_baseaddr;
void __iomem *gpmc_baseaddr;
void __iomem *nand_pref_fifo_add;
struct completion comp;
int dma_ch;
};
/**
* omap_nand_wp - This function enable or disable the Write Protect feature
* @mtd: MTD device structure
* @mode: WP ON/OFF
*/
static void omap_nand_wp(struct mtd_info *mtd, int mode)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
unsigned long config = __raw_readl(info->gpmc_baseaddr + GPMC_CONFIG);
if (mode)
config &= ~(NAND_WP_BIT); /* WP is ON */
else
config |= (NAND_WP_BIT); /* WP is OFF */
__raw_writel(config, (info->gpmc_baseaddr + GPMC_CONFIG));
}
/**
* omap_hwcontrol - hardware specific access to control-lines
* @mtd: MTD device structure
......@@ -181,31 +147,17 @@ static void omap_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
switch (ctrl) {
case NAND_CTRL_CHANGE | NAND_CTRL_CLE:
info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_COMMAND;
info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_DATA;
break;
case NAND_CTRL_CHANGE | NAND_CTRL_ALE:
info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_ADDRESS;
info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_DATA;
break;
case NAND_CTRL_CHANGE | NAND_NCE:
info->nand.IO_ADDR_W = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_DATA;
info->nand.IO_ADDR_R = info->gpmc_cs_baseaddr +
GPMC_CS_NAND_DATA;
break;
}
if (cmd != NAND_CMD_NONE)
__raw_writeb(cmd, info->nand.IO_ADDR_W);
if (cmd != NAND_CMD_NONE) {
if (ctrl & NAND_CLE)
gpmc_nand_write(info->gpmc_cs, GPMC_NAND_COMMAND, cmd);
else if (ctrl & NAND_ALE)
gpmc_nand_write(info->gpmc_cs, GPMC_NAND_ADDRESS, cmd);
else /* NAND_NCE */
gpmc_nand_write(info->gpmc_cs, GPMC_NAND_DATA, cmd);
}
}
/**
......@@ -232,11 +184,14 @@ static void omap_write_buf8(struct mtd_info *mtd, const u_char *buf, int len)
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
u_char *p = (u_char *)buf;
u32 status = 0;
while (len--) {
iowrite8(*p++, info->nand.IO_ADDR_W);
while (GPMC_BUF_EMPTY == (readl(info->gpmc_baseaddr +
GPMC_STATUS) & GPMC_BUF_FULL));
/* wait until buffer is available for write */
do {
status = gpmc_read_status(GPMC_STATUS_BUFFER);
} while (!status);
}
}
......@@ -264,16 +219,16 @@ static void omap_write_buf16(struct mtd_info *mtd, const u_char * buf, int len)
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
u16 *p = (u16 *) buf;
u32 status = 0;
/* FIXME try bursts of writesw() or DMA ... */
len >>= 1;
while (len--) {
iowrite16(*p++, info->nand.IO_ADDR_W);
while (GPMC_BUF_EMPTY == (readl(info->gpmc_baseaddr +
GPMC_STATUS) & GPMC_BUF_FULL))
;
/* wait until buffer is available for write */
do {
status = gpmc_read_status(GPMC_STATUS_BUFFER);
} while (!status);
}
}
......@@ -287,7 +242,7 @@ static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
uint32_t pfpw_status = 0, r_count = 0;
uint32_t r_count = 0;
int ret = 0;
u32 *p = (u32 *)buf;
......@@ -310,14 +265,14 @@ static void omap_read_buf_pref(struct mtd_info *mtd, u_char *buf, int len)
else
omap_read_buf8(mtd, buf, len);
} else {
p = (u32 *) buf;
do {
pfpw_status = gpmc_prefetch_status();
r_count = ((pfpw_status >> 24) & 0x7F) >> 2;
ioread32_rep(info->nand_pref_fifo_add, p, r_count);
r_count = gpmc_read_status(GPMC_PREFETCH_FIFO_CNT);
r_count = r_count >> 2;
ioread32_rep(info->nand.IO_ADDR_R, p, r_count);
p += r_count;
len -= r_count << 2;
} while (len);
/* disable and stop the PFPW engine */
gpmc_prefetch_reset(info->gpmc_cs);
}
......@@ -334,13 +289,13 @@ static void omap_write_buf_pref(struct mtd_info *mtd,
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
uint32_t pfpw_status = 0, w_count = 0;
uint32_t pref_count = 0, w_count = 0;
int i = 0, ret = 0;
u16 *p = (u16 *) buf;
u16 *p;
/* take care of subpage writes */
if (len % 2 != 0) {
writeb(*buf, info->nand.IO_ADDR_R);
writeb(*buf, info->nand.IO_ADDR_W);
p = (u16 *)(buf + 1);
len--;
}
......@@ -354,14 +309,17 @@ static void omap_write_buf_pref(struct mtd_info *mtd,
else
omap_write_buf8(mtd, buf, len);
} else {
pfpw_status = gpmc_prefetch_status();
while (pfpw_status & 0x3FFF) {
w_count = ((pfpw_status >> 24) & 0x7F) >> 1;
p = (u16 *) buf;
while (len) {
w_count = gpmc_read_status(GPMC_PREFETCH_FIFO_CNT);
w_count = w_count >> 1;
for (i = 0; (i < w_count) && len; i++, len -= 2)
iowrite16(*p++, info->nand_pref_fifo_add);
pfpw_status = gpmc_prefetch_status();
iowrite16(*p++, info->nand.IO_ADDR_W);
}
/* wait for data to flushed-out before reset the prefetch */
do {
pref_count = gpmc_read_status(GPMC_PREFETCH_COUNT);
} while (pref_count);
/* disable and stop the PFPW engine */
gpmc_prefetch_reset(info->gpmc_cs);
}
......@@ -451,8 +409,9 @@ static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr,
/* setup and start DMA using dma_addr */
wait_for_completion(&info->comp);
while (0x3fff & (prefetch_status = gpmc_prefetch_status()))
;
do {
prefetch_status = gpmc_read_status(GPMC_PREFETCH_COUNT);
} while (prefetch_status);
/* disable and stop the PFPW engine */
gpmc_prefetch_reset();
......@@ -530,29 +489,6 @@ static int omap_verify_buf(struct mtd_info *mtd, const u_char * buf, int len)
}
#ifdef CONFIG_MTD_NAND_OMAP_HWECC
/**
* omap_hwecc_init - Initialize the HW ECC for NAND flash in GPMC controller
* @mtd: MTD device structure
*/
static void omap_hwecc_init(struct mtd_info *mtd)
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
struct nand_chip *chip = mtd->priv;
unsigned long val = 0x0;
/* Read from ECC Control Register */
val = __raw_readl(info->gpmc_baseaddr + GPMC_ECC_CONTROL);
/* Clear all ECC | Enable Reg1 */
val = ((0x00000001<<8) | 0x00000001);
__raw_writel(val, info->gpmc_baseaddr + GPMC_ECC_CONTROL);
/* Read from ECC Size Config Register */
val = __raw_readl(info->gpmc_baseaddr + GPMC_ECC_SIZE_CONFIG);
/* ECCSIZE1=512 | Select eccResultsize[0-3] */
val = ((((chip->ecc.size >> 1) - 1) << 22) | (0x0000000F));
__raw_writel(val, info->gpmc_baseaddr + GPMC_ECC_SIZE_CONFIG);
}
/**
* gen_true_ecc - This function will generate true ECC value
......@@ -755,19 +691,7 @@ static int omap_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
{
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
unsigned long val = 0x0;
unsigned long reg;
/* Start Reading from HW ECC1_Result = 0x200 */
reg = (unsigned long)(info->gpmc_baseaddr + GPMC_ECC1_RESULT);
val = __raw_readl(reg);
*ecc_code++ = val; /* P128e, ..., P1e */
*ecc_code++ = val >> 16; /* P128o, ..., P1o */
/* P2048o, P1024o, P512o, P256o, P2048e, P1024e, P512e, P256e */
*ecc_code++ = ((val >> 8) & 0x0f) | ((val >> 20) & 0xf0);
reg += 4;
return 0;
return gpmc_calculate_ecc(info->gpmc_cs, dat, ecc_code);
}
/**
......@@ -781,32 +705,10 @@ static void omap_enable_hwecc(struct mtd_info *mtd, int mode)
mtd);
struct nand_chip *chip = mtd->priv;
unsigned int dev_width = (chip->options & NAND_BUSWIDTH_16) ? 1 : 0;
unsigned long val = __raw_readl(info->gpmc_baseaddr + GPMC_ECC_CONFIG);
switch (mode) {
case NAND_ECC_READ:
__raw_writel(0x101, info->gpmc_baseaddr + GPMC_ECC_CONTROL);
/* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */
val = (dev_width << 7) | (info->gpmc_cs << 1) | (0x1);
break;
case NAND_ECC_READSYN:
__raw_writel(0x100, info->gpmc_baseaddr + GPMC_ECC_CONTROL);
/* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */
val = (dev_width << 7) | (info->gpmc_cs << 1) | (0x1);
break;
case NAND_ECC_WRITE:
__raw_writel(0x101, info->gpmc_baseaddr + GPMC_ECC_CONTROL);
/* (ECC 16 or 8 bit col) | ( CS ) | ECC Enable */
val = (dev_width << 7) | (info->gpmc_cs << 1) | (0x1);
break;
default:
DEBUG(MTD_DEBUG_LEVEL0, "Error: Unrecognized Mode[%d]!\n",
mode);
break;
}
__raw_writel(val, info->gpmc_baseaddr + GPMC_ECC_CONFIG);
gpmc_enable_hwecc(info->gpmc_cs, mode, dev_width, info->nand.ecc.size);
}
#endif
/**
......@@ -834,14 +736,10 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip)
else
timeo += (HZ * 20) / 1000;
this->IO_ADDR_W = (void *) info->gpmc_cs_baseaddr +
GPMC_CS_NAND_COMMAND;
this->IO_ADDR_R = (void *) info->gpmc_cs_baseaddr + GPMC_CS_NAND_DATA;
__raw_writeb(NAND_CMD_STATUS & 0xFF, this->IO_ADDR_W);
gpmc_nand_write(info->gpmc_cs,
GPMC_NAND_COMMAND, (NAND_CMD_STATUS & 0xFF));
while (time_before(jiffies, timeo)) {
status = __raw_readb(this->IO_ADDR_R);
status = gpmc_nand_read(info->gpmc_cs, GPMC_NAND_DATA);
if (status & NAND_STATUS_READY)
break;
cond_resched();
......@@ -855,22 +753,22 @@ static int omap_wait(struct mtd_info *mtd, struct nand_chip *chip)
*/
static int omap_dev_ready(struct mtd_info *mtd)
{
unsigned int val = 0;
struct omap_nand_info *info = container_of(mtd, struct omap_nand_info,
mtd);
unsigned int val = __raw_readl(info->gpmc_baseaddr + GPMC_IRQ_STATUS);
val = gpmc_read_status(GPMC_GET_IRQ_STATUS);
if ((val & 0x100) == 0x100) {
/* Clear IRQ Interrupt */
val |= 0x100;
val &= ~(0x0);
__raw_writel(val, info->gpmc_baseaddr + GPMC_IRQ_STATUS);
gpmc_cs_configure(info->gpmc_cs, GPMC_SET_IRQ_STATUS, val);
} else {
unsigned int cnt = 0;
while (cnt++ < 0x1FF) {
if ((val & 0x100) == 0x100)
return 0;
val = __raw_readl(info->gpmc_baseaddr +
GPMC_IRQ_STATUS);
val = gpmc_read_status(GPMC_GET_IRQ_STATUS);
}
}
......@@ -901,8 +799,6 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
info->pdev = pdev;
info->gpmc_cs = pdata->cs;
info->gpmc_baseaddr = pdata->gpmc_baseaddr;
info->gpmc_cs_baseaddr = pdata->gpmc_cs_baseaddr;
info->phys_base = pdata->phys_base;
info->mtd.priv = &info->nand;
......@@ -913,7 +809,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
info->nand.options |= NAND_SKIP_BBTSCAN;
/* NAND write protect off */
omap_nand_wp(&info->mtd, NAND_WP_OFF);
gpmc_cs_configure(info->gpmc_cs, GPMC_CONFIG_WP, 0);
if (!request_mem_region(info->phys_base, NAND_IO_SIZE,
pdev->dev.driver->name)) {
......@@ -948,8 +844,6 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
}
if (use_prefetch) {
/* copy the virtual address of nand base for fifo access */
info->nand_pref_fifo_add = info->nand.IO_ADDR_R;
info->nand.read_buf = omap_read_buf_pref;
info->nand.write_buf = omap_write_buf_pref;
......@@ -989,8 +883,6 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
info->nand.ecc.correct = omap_correct_data;
info->nand.ecc.mode = NAND_ECC_HW;
/* init HW ECC */
omap_hwecc_init(&info->mtd);
#else
info->nand.ecc.mode = NAND_ECC_SOFT;
#endif
......@@ -1040,7 +932,7 @@ static int omap_nand_remove(struct platform_device *pdev)
/* Release NAND device, its internal structures and partitions */
nand_release(&info->mtd);
iounmap(info->nand_pref_fifo_add);
iounmap(info->nand.IO_ADDR_R);
kfree(&info->mtd);
return 0;
}
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册