提交 225aa011 编写于 作者: L Linus Torvalds

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: add pipe A force quirks to i915 driver
  drm/i915: Fix panel fitting regression since 734b4157
  drm/i915: fix deadlock in fb teardown
  drm/i915: don't free non-existent compressed llb on ILK+
  agp/intel: Use the correct mask to detect i830 aperture size.
  drm/i915: disable FBC when more than one pipe is active
  drm/i915: Use the correct scanout alignment for fbcon.
  drm/i915: make sure eDP panel is turned on
  drm/i915: add PANEL_UNLOCK_REGS definition
  drm/i915: Make G4X-style PLL search more permissive
  drm/i915: Clear any existing dither mode prior to enabling spatial dithering
  drm/i915: handle shared framebuffers when flipping
  drm/i915: Explosion following OOM in do_execbuffer.
  gpu/drm/i915: Add a blacklist to omit modeset on LID open
......@@ -1216,17 +1216,20 @@ static int intel_i915_get_gtt_size(void)
/* G33's GTT size defined in gmch_ctrl */
pci_read_config_word(agp_bridge->dev, I830_GMCH_CTRL, &gmch_ctrl);
switch (gmch_ctrl & G33_PGETBL_SIZE_MASK) {
case G33_PGETBL_SIZE_1M:
switch (gmch_ctrl & I830_GMCH_GMS_MASK) {
case I830_GMCH_GMS_STOLEN_512:
size = 512;
break;
case I830_GMCH_GMS_STOLEN_1024:
size = 1024;
break;
case G33_PGETBL_SIZE_2M:
size = 2048;
case I830_GMCH_GMS_STOLEN_8192:
size = 8*1024;
break;
default:
dev_info(&agp_bridge->dev->dev,
"unknown page table size 0x%x, assuming 512KB\n",
(gmch_ctrl & G33_PGETBL_SIZE_MASK));
(gmch_ctrl & I830_GMCH_GMS_MASK));
size = 512;
}
} else {
......
......@@ -605,6 +605,9 @@ static int i915_fbc_status(struct seq_file *m, void *unused)
case FBC_NOT_TILED:
seq_printf(m, "scanout buffer not tiled");
break;
case FBC_MULTIPLE_PIPES:
seq_printf(m, "multiple pipes are enabled");
break;
default:
seq_printf(m, "unknown reason");
}
......
......@@ -1300,7 +1300,7 @@ static void i915_cleanup_compression(struct drm_device *dev)
struct drm_i915_private *dev_priv = dev->dev_private;
drm_mm_put_block(dev_priv->compressed_fb);
if (!IS_GM45(dev))
if (dev_priv->compressed_llb)
drm_mm_put_block(dev_priv->compressed_llb);
}
......
......@@ -215,6 +215,7 @@ enum no_fbc_reason {
FBC_MODE_TOO_LARGE, /* mode too large for compression */
FBC_BAD_PLANE, /* fbc not supported on plane */
FBC_NOT_TILED, /* buffer not tiled */
FBC_MULTIPLE_PIPES, /* more than one pipe active */
};
enum intel_pch {
......@@ -222,6 +223,8 @@ enum intel_pch {
PCH_CPT, /* Cougarpoint PCH */
};
#define QUIRK_PIPEA_FORCE (1<<0)
struct intel_fbdev;
typedef struct drm_i915_private {
......@@ -337,6 +340,8 @@ typedef struct drm_i915_private {
/* PCH chipset type */
enum intel_pch pch_type;
unsigned long quirks;
/* Register state */
bool modeset_on_lid;
u8 saveLBB;
......
......@@ -3647,6 +3647,7 @@ i915_gem_wait_for_pending_flip(struct drm_device *dev,
return ret;
}
int
i915_gem_do_execbuffer(struct drm_device *dev, void *data,
struct drm_file *file_priv,
......@@ -3794,7 +3795,7 @@ i915_gem_do_execbuffer(struct drm_device *dev, void *data,
unsigned long long total_size = 0;
int num_fences = 0;
for (i = 0; i < args->buffer_count; i++) {
obj_priv = object_list[i]->driver_private;
obj_priv = to_intel_bo(object_list[i]);
total_size += object_list[i]->size;
num_fences +=
......
......@@ -2869,6 +2869,7 @@
#define PCH_PP_STATUS 0xc7200
#define PCH_PP_CONTROL 0xc7204
#define PANEL_UNLOCK_REGS (0xabcd << 16)
#define EDP_FORCE_VDD (1 << 3)
#define EDP_BLC_ENABLE (1 << 2)
#define PANEL_POWER_RESET (1 << 1)
......
......@@ -862,8 +862,8 @@ intel_g4x_find_best_PLL(const intel_limit_t *limit, struct drm_crtc *crtc,
intel_clock_t clock;
int max_n;
bool found;
/* approximately equals target * 0.00488 */
int err_most = (target >> 8) + (target >> 10);
/* approximately equals target * 0.00585 */
int err_most = (target >> 8) + (target >> 9);
found = false;
if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS)) {
......@@ -1180,8 +1180,12 @@ static void intel_update_fbc(struct drm_crtc *crtc,
struct drm_framebuffer *fb = crtc->fb;
struct intel_framebuffer *intel_fb;
struct drm_i915_gem_object *obj_priv;
struct drm_crtc *tmp_crtc;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
int plane = intel_crtc->plane;
int crtcs_enabled = 0;
DRM_DEBUG_KMS("\n");
if (!i915_powersave)
return;
......@@ -1199,10 +1203,21 @@ static void intel_update_fbc(struct drm_crtc *crtc,
* If FBC is already on, we just have to verify that we can
* keep it that way...
* Need to disable if:
* - more than one pipe is active
* - changing FBC params (stride, fence, mode)
* - new fb is too large to fit in compressed buffer
* - going to an unsupported config (interlace, pixel multiply, etc.)
*/
list_for_each_entry(tmp_crtc, &dev->mode_config.crtc_list, head) {
if (tmp_crtc->enabled)
crtcs_enabled++;
}
DRM_DEBUG_KMS("%d pipes active\n", crtcs_enabled);
if (crtcs_enabled > 1) {
DRM_DEBUG_KMS("more than one pipe active, disabling compression\n");
dev_priv->no_fbc_reason = FBC_MULTIPLE_PIPES;
goto out_disable;
}
if (intel_fb->obj->size > dev_priv->cfb_size) {
DRM_DEBUG_KMS("framebuffer too large, disabling "
"compression\n");
......@@ -1255,7 +1270,7 @@ static void intel_update_fbc(struct drm_crtc *crtc,
}
}
static int
int
intel_pin_and_fence_fb_obj(struct drm_device *dev, struct drm_gem_object *obj)
{
struct drm_i915_gem_object *obj_priv = to_intel_bo(obj);
......@@ -2255,6 +2270,11 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
intel_wait_for_vblank(dev);
}
/* Don't disable pipe A or pipe A PLLs if needed */
if (pipeconf_reg == PIPEACONF &&
(dev_priv->quirks & QUIRK_PIPEA_FORCE))
goto skip_pipe_off;
/* Next, disable display pipes */
temp = I915_READ(pipeconf_reg);
if ((temp & PIPEACONF_ENABLE) != 0) {
......@@ -2270,7 +2290,7 @@ static void i9xx_crtc_dpms(struct drm_crtc *crtc, int mode)
I915_WRITE(dpll_reg, temp & ~DPLL_VCO_ENABLE);
I915_READ(dpll_reg);
}
skip_pipe_off:
/* Wait for the clocks to turn off. */
udelay(150);
break;
......@@ -2356,8 +2376,6 @@ static bool intel_crtc_mode_fixup(struct drm_crtc *crtc,
if (mode->clock * 3 > 27000 * 4)
return MODE_CLOCK_HIGH;
}
drm_mode_set_crtcinfo(adjusted_mode, 0);
return true;
}
......@@ -3736,6 +3754,7 @@ static int intel_crtc_mode_set(struct drm_crtc *crtc,
if (dev_priv->lvds_dither) {
if (HAS_PCH_SPLIT(dev)) {
pipeconf |= PIPE_ENABLE_DITHER;
pipeconf &= ~PIPE_DITHER_TYPE_MASK;
pipeconf |= PIPE_DITHER_TYPE_ST01;
} else
lvds |= LVDS_ENABLE_DITHER;
......@@ -4412,7 +4431,8 @@ static void intel_increase_pllclock(struct drm_crtc *crtc, bool schedule)
DRM_DEBUG_DRIVER("upclocking LVDS\n");
/* Unlock panel regs */
I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) | (0xabcd << 16));
I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) |
PANEL_UNLOCK_REGS);
dpll &= ~DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
......@@ -4455,7 +4475,8 @@ static void intel_decrease_pllclock(struct drm_crtc *crtc)
DRM_DEBUG_DRIVER("downclocking LVDS\n");
/* Unlock panel regs */
I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) | (0xabcd << 16));
I915_WRITE(PP_CONTROL, I915_READ(PP_CONTROL) |
PANEL_UNLOCK_REGS);
dpll |= DISPLAY_RATE_SELECT_FPA1;
I915_WRITE(dpll_reg, dpll);
......@@ -4695,7 +4716,7 @@ static int intel_crtc_page_flip(struct drm_crtc *crtc,
struct drm_gem_object *obj;
struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
struct intel_unpin_work *work;
unsigned long flags;
unsigned long flags, offset;
int pipesrc_reg = (intel_crtc->pipe == 0) ? PIPEASRC : PIPEBSRC;
int ret, pipesrc;
u32 flip_mask;
......@@ -4762,19 +4783,23 @@ static int intel_crtc_page_flip(struct drm_crtc *crtc,
while (I915_READ(ISR) & flip_mask)
;
/* Offset into the new buffer for cases of shared fbs between CRTCs */
offset = obj_priv->gtt_offset;
offset += (crtc->y * fb->pitch) + (crtc->x * (fb->bits_per_pixel) / 8);
BEGIN_LP_RING(4);
if (IS_I965G(dev)) {
OUT_RING(MI_DISPLAY_FLIP |
MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
OUT_RING(fb->pitch);
OUT_RING(obj_priv->gtt_offset | obj_priv->tiling_mode);
OUT_RING(offset | obj_priv->tiling_mode);
pipesrc = I915_READ(pipesrc_reg);
OUT_RING(pipesrc & 0x0fff0fff);
} else {
OUT_RING(MI_DISPLAY_FLIP_I915 |
MI_DISPLAY_FLIP_PLANE(intel_crtc->plane));
OUT_RING(fb->pitch);
OUT_RING(obj_priv->gtt_offset);
OUT_RING(offset);
OUT_RING(MI_NOOP);
}
ADVANCE_LP_RING();
......@@ -5506,6 +5531,66 @@ static void intel_init_display(struct drm_device *dev)
}
}
/*
* Some BIOSes insist on assuming the GPU's pipe A is enabled at suspend,
* resume, or other times. This quirk makes sure that's the case for
* affected systems.
*/
static void quirk_pipea_force (struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
dev_priv->quirks |= QUIRK_PIPEA_FORCE;
DRM_DEBUG_DRIVER("applying pipe a force quirk\n");
}
struct intel_quirk {
int device;
int subsystem_vendor;
int subsystem_device;
void (*hook)(struct drm_device *dev);
};
struct intel_quirk intel_quirks[] = {
/* HP Compaq 2730p needs pipe A force quirk (LP: #291555) */
{ 0x2a42, 0x103c, 0x30eb, quirk_pipea_force },
/* HP Mini needs pipe A force quirk (LP: #322104) */
{ 0x27ae,0x103c, 0x361a, quirk_pipea_force },
/* Thinkpad R31 needs pipe A force quirk */
{ 0x3577, 0x1014, 0x0505, quirk_pipea_force },
/* Toshiba Protege R-205, S-209 needs pipe A force quirk */
{ 0x2592, 0x1179, 0x0001, quirk_pipea_force },
/* ThinkPad X30 needs pipe A force quirk (LP: #304614) */
{ 0x3577, 0x1014, 0x0513, quirk_pipea_force },
/* ThinkPad X40 needs pipe A force quirk */
/* ThinkPad T60 needs pipe A force quirk (bug #16494) */
{ 0x2782, 0x17aa, 0x201a, quirk_pipea_force },
/* 855 & before need to leave pipe A & dpll A up */
{ 0x3582, PCI_ANY_ID, PCI_ANY_ID, quirk_pipea_force },
{ 0x2562, PCI_ANY_ID, PCI_ANY_ID, quirk_pipea_force },
};
static void intel_init_quirks(struct drm_device *dev)
{
struct pci_dev *d = dev->pdev;
int i;
for (i = 0; i < ARRAY_SIZE(intel_quirks); i++) {
struct intel_quirk *q = &intel_quirks[i];
if (d->device == q->device &&
(d->subsystem_vendor == q->subsystem_vendor ||
q->subsystem_vendor == PCI_ANY_ID) &&
(d->subsystem_device == q->subsystem_device ||
q->subsystem_device == PCI_ANY_ID))
q->hook(dev);
}
}
void intel_modeset_init(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
......@@ -5518,6 +5603,8 @@ void intel_modeset_init(struct drm_device *dev)
dev->mode_config.funcs = (void *)&intel_mode_funcs;
intel_init_quirks(dev);
intel_init_display(dev);
if (IS_I965G(dev)) {
......
......@@ -717,6 +717,51 @@ intel_dp_mode_set(struct drm_encoder *encoder, struct drm_display_mode *mode,
}
}
static void ironlake_edp_panel_on (struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
unsigned long timeout = jiffies + msecs_to_jiffies(5000);
u32 pp, pp_status;
pp_status = I915_READ(PCH_PP_STATUS);
if (pp_status & PP_ON)
return;
pp = I915_READ(PCH_PP_CONTROL);
pp |= PANEL_UNLOCK_REGS | POWER_TARGET_ON;
I915_WRITE(PCH_PP_CONTROL, pp);
do {
pp_status = I915_READ(PCH_PP_STATUS);
} while (((pp_status & PP_ON) == 0) && !time_after(jiffies, timeout));
if (time_after(jiffies, timeout))
DRM_DEBUG_KMS("panel on wait timed out: 0x%08x\n", pp_status);
pp &= ~(PANEL_UNLOCK_REGS | EDP_FORCE_VDD);
I915_WRITE(PCH_PP_CONTROL, pp);
}
static void ironlake_edp_panel_off (struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
unsigned long timeout = jiffies + msecs_to_jiffies(5000);
u32 pp, pp_status;
pp = I915_READ(PCH_PP_CONTROL);
pp &= ~POWER_TARGET_ON;
I915_WRITE(PCH_PP_CONTROL, pp);
do {
pp_status = I915_READ(PCH_PP_STATUS);
} while ((pp_status & PP_ON) && !time_after(jiffies, timeout));
if (time_after(jiffies, timeout))
DRM_DEBUG_KMS("panel off wait timed out\n");
/* Make sure VDD is enabled so DP AUX will work */
pp |= EDP_FORCE_VDD;
I915_WRITE(PCH_PP_CONTROL, pp);
}
static void ironlake_edp_backlight_on (struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
......@@ -751,14 +796,18 @@ intel_dp_dpms(struct drm_encoder *encoder, int mode)
if (mode != DRM_MODE_DPMS_ON) {
if (dp_reg & DP_PORT_EN) {
intel_dp_link_down(intel_encoder, dp_priv->DP);
if (IS_eDP(intel_encoder))
if (IS_eDP(intel_encoder)) {
ironlake_edp_backlight_off(dev);
ironlake_edp_backlight_off(dev);
}
}
} else {
if (!(dp_reg & DP_PORT_EN)) {
intel_dp_link_train(intel_encoder, dp_priv->DP, dp_priv->link_configuration);
if (IS_eDP(intel_encoder))
if (IS_eDP(intel_encoder)) {
ironlake_edp_panel_on(dev);
ironlake_edp_backlight_on(dev);
}
}
}
dp_priv->dpms_mode = mode;
......
......@@ -215,6 +215,9 @@ extern void intel_init_clock_gating(struct drm_device *dev);
extern void ironlake_enable_drps(struct drm_device *dev);
extern void ironlake_disable_drps(struct drm_device *dev);
extern int intel_pin_and_fence_fb_obj(struct drm_device *dev,
struct drm_gem_object *obj);
extern int intel_framebuffer_init(struct drm_device *dev,
struct intel_framebuffer *ifb,
struct drm_mode_fb_cmd *mode_cmd,
......
......@@ -98,7 +98,7 @@ static int intelfb_create(struct intel_fbdev *ifbdev,
mutex_lock(&dev->struct_mutex);
ret = i915_gem_object_pin(fbo, 64*1024);
ret = intel_pin_and_fence_fb_obj(dev, fbo);
if (ret) {
DRM_ERROR("failed to pin fb: %d\n", ret);
goto out_unref;
......@@ -236,7 +236,7 @@ int intel_fbdev_destroy(struct drm_device *dev,
drm_framebuffer_cleanup(&ifb->base);
if (ifb->obj)
drm_gem_object_unreference_unlocked(ifb->obj);
drm_gem_object_unreference(ifb->obj);
return 0;
}
......
......@@ -599,6 +599,26 @@ static int intel_lvds_get_modes(struct drm_connector *connector)
return 0;
}
static int intel_no_modeset_on_lid_dmi_callback(const struct dmi_system_id *id)
{
DRM_DEBUG_KMS("Skipping forced modeset for %s\n", id->ident);
return 1;
}
/* The GPU hangs up on these systems if modeset is performed on LID open */
static const struct dmi_system_id intel_no_modeset_on_lid[] = {
{
.callback = intel_no_modeset_on_lid_dmi_callback,
.ident = "Toshiba Tecra A11",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
DMI_MATCH(DMI_PRODUCT_NAME, "TECRA A11"),
},
},
{ } /* terminating entry */
};
/*
* Lid events. Note the use of 'modeset_on_lid':
* - we set it on lid close, and reset it on open
......@@ -622,6 +642,9 @@ static int intel_lid_notify(struct notifier_block *nb, unsigned long val,
*/
if (connector)
connector->status = connector->funcs->detect(connector);
/* Don't force modeset on machines where it causes a GPU lockup */
if (dmi_check_system(intel_no_modeset_on_lid))
return NOTIFY_OK;
if (!acpi_lid_open()) {
dev_priv->modeset_on_lid = 1;
return NOTIFY_OK;
......
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册