提交 20f18ff3 编写于 作者: M Marc Zyngier 提交者: Marc Zyngier

Add support for the Arcom/Eurotech Viper SBC CompactFlash card slot

The Arcom/Eurotech Viper needs some extra care to run. On this board,
the PC104 connector is actually wired to the second PCMCIA slot.
Therefore, this second socket needs to be enabled, despite not being
managed by the PCMCIA code.

I'd rather have the MECR setup in the platform support code so I could,
for example, use the PC104 bus without having the PCMCIA module loaded.
Signed-off-by: NMarc Zyngier <marc.zyngier@altran.com>
上级 175ff20f
......@@ -220,7 +220,7 @@ config PCMCIA_PXA2XX
tristate "PXA2xx support"
depends on ARM && ARCH_PXA && PCMCIA
depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \
|| MACH_ARMCORE || ARCH_PXA_PALM)
|| MACH_ARMCORE || ARCH_PXA_PALM || ARCH_VIPER)
help
Say Y here to include support for the PXA2xx PCMCIA controller
......
......@@ -72,5 +72,6 @@ pxa2xx_cs-$(CONFIG_ARCH_LUBBOCK) += pxa2xx_lubbock.o sa1111_generic.o
pxa2xx_cs-$(CONFIG_MACH_MAINSTONE) += pxa2xx_mainstone.o
pxa2xx_cs-$(CONFIG_PXA_SHARPSL) += pxa2xx_sharpsl.o
pxa2xx_cs-$(CONFIG_MACH_ARMCORE) += pxa2xx_cm_x270.o
pxa2xx_cs-$(CONFIG_ARCH_VIPER) += pxa2xx_viper.o
pxa2xx_cs-$(CONFIG_MACH_PALMTX) += pxa2xx_palmtx.o
......@@ -30,6 +30,7 @@
#include <asm/system.h>
#include <mach/pxa-regs.h>
#include <mach/pxa2xx-regs.h>
#include <asm/mach-types.h>
#include <pcmcia/cs_types.h>
#include <pcmcia/ss.h>
......@@ -166,18 +167,32 @@ pxa2xx_pcmcia_frequency_change(struct soc_pcmcia_socket *skt,
}
#endif
static void pxa2xx_configure_sockets(struct device *dev)
{
struct pcmcia_low_level *ops = dev->platform_data;
/*
* We have at least one socket, so set MECR:CIT
* (Card Is There)
*/
MECR |= MECR_CIT;
/* Set MECR:NOS (Number Of Sockets) */
if (ops->nr > 1 || machine_is_viper())
MECR |= MECR_NOS;
else
MECR &= ~MECR_NOS;
}
int __pxa2xx_drv_pcmcia_probe(struct device *dev)
{
int ret;
struct pcmcia_low_level *ops;
int first, nr;
if (!dev || !dev->platform_data)
return -ENODEV;
ops = (struct pcmcia_low_level *)dev->platform_data;
first = ops->first;
nr = ops->nr;
/* Provide our PXA2xx specific timing routines. */
ops->set_timing = pxa2xx_pcmcia_set_timing;
......@@ -185,21 +200,10 @@ int __pxa2xx_drv_pcmcia_probe(struct device *dev)
ops->frequency_change = pxa2xx_pcmcia_frequency_change;
#endif
ret = soc_common_drv_pcmcia_probe(dev, ops, first, nr);
ret = soc_common_drv_pcmcia_probe(dev, ops, ops->first, ops->nr);
if (ret == 0) {
/*
* We have at least one socket, so set MECR:CIT
* (Card Is There)
*/
MECR |= MECR_CIT;
/* Set MECR:NOS (Number Of Sockets) */
if (nr > 1)
MECR |= MECR_NOS;
else
MECR &= ~MECR_NOS;
}
if (!ret)
pxa2xx_configure_sockets(dev);
return ret;
}
......@@ -223,11 +227,7 @@ static int pxa2xx_drv_pcmcia_suspend(struct platform_device *dev, pm_message_t s
static int pxa2xx_drv_pcmcia_resume(struct platform_device *dev)
{
struct pcmcia_low_level *ops = dev->dev.platform_data;
int nr = ops ? ops->nr : 0;
MECR = nr > 1 ? MECR_CIT | MECR_NOS : (nr > 0 ? MECR_CIT : 0);
pxa2xx_configure_sockets(&dev->dev);
return pcmcia_socket_dev_resume(&dev->dev);
}
......
/*
* VIPER PCMCIA support
* Copyright 2004 Arcom Control Systems
*
* Maintained by Marc Zyngier <maz@misterjones.org>
* <marc.zyngier@altran.com>
*
* Based on:
* iPAQ h2200 PCMCIA support
* Copyright 2004 Koen Kooi <koen@vestingbar.nl>
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file COPYING in the main directory of this archive for
* more details.
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <pcmcia/ss.h>
#include <asm/irq.h>
#include <mach/pxa-regs.h>
#include <mach/viper.h>
#include <asm/mach-types.h>
#include "soc_common.h"
#include "pxa2xx_base.h"
static struct pcmcia_irqs irqs[] = {
{ 0, gpio_to_irq(VIPER_CF_CD_GPIO), "PCMCIA_CD" }
};
static int viper_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
{
unsigned long flags;
skt->irq = gpio_to_irq(VIPER_CF_RDY_GPIO);
if (gpio_request(VIPER_CF_CD_GPIO, "CF detect"))
goto err_request_cd;
if (gpio_request(VIPER_CF_RDY_GPIO, "CF ready"))
goto err_request_rdy;
if (gpio_request(VIPER_CF_POWER_GPIO, "CF power"))
goto err_request_pwr;
local_irq_save(flags);
/* GPIO 82 is the CF power enable line. initially off */
if (gpio_direction_output(VIPER_CF_POWER_GPIO, 0) ||
gpio_direction_input(VIPER_CF_CD_GPIO) ||
gpio_direction_input(VIPER_CF_RDY_GPIO)) {
local_irq_restore(flags);
goto err_dir;
}
local_irq_restore(flags);
return soc_pcmcia_request_irqs(skt, irqs, ARRAY_SIZE(irqs));
err_dir:
gpio_free(VIPER_CF_POWER_GPIO);
err_request_pwr:
gpio_free(VIPER_CF_RDY_GPIO);
err_request_rdy:
gpio_free(VIPER_CF_CD_GPIO);
err_request_cd:
printk(KERN_ERR "viper: Failed to setup PCMCIA GPIOs\n");
return -1;
}
/*
* Release all resources.
*/
static void viper_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
{
soc_pcmcia_free_irqs(skt, irqs, ARRAY_SIZE(irqs));
gpio_free(VIPER_CF_POWER_GPIO);
gpio_free(VIPER_CF_RDY_GPIO);
gpio_free(VIPER_CF_CD_GPIO);
}
static void viper_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
struct pcmcia_state *state)
{
state->detect = gpio_get_value(VIPER_CF_CD_GPIO) ? 0 : 1;
state->ready = gpio_get_value(VIPER_CF_RDY_GPIO) ? 1 : 0;
state->bvd1 = 1;
state->bvd2 = 1;
state->wrprot = 0;
state->vs_3v = 1; /* Can only apply 3.3V */
state->vs_Xv = 0;
}
static int viper_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
const socket_state_t *state)
{
/* Silently ignore Vpp, output enable, speaker enable. */
viper_cf_rst(state->flags & SS_RESET);
/* Apply socket voltage */
switch (state->Vcc) {
case 0:
gpio_set_value(VIPER_CF_POWER_GPIO, 0);
break;
case 33:
gpio_set_value(VIPER_CF_POWER_GPIO, 1);
break;
default:
printk(KERN_ERR "%s: Unsupported Vcc:%d\n",
__func__, state->Vcc);
return -1;
}
return 0;
}
static void viper_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
{
}
static void viper_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
{
}
static struct pcmcia_low_level viper_pcmcia_ops __initdata = {
.owner = THIS_MODULE,
.hw_init = viper_pcmcia_hw_init,
.hw_shutdown = viper_pcmcia_hw_shutdown,
.socket_state = viper_pcmcia_socket_state,
.configure_socket = viper_pcmcia_configure_socket,
.socket_init = viper_pcmcia_socket_init,
.socket_suspend = viper_pcmcia_socket_suspend,
.nr = 1,
};
static struct platform_device *viper_pcmcia_device;
static int __init viper_pcmcia_init(void)
{
int ret;
if (!machine_is_viper())
return -ENODEV;
viper_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
if (!viper_pcmcia_device)
return -ENOMEM;
ret = platform_device_add_data(viper_pcmcia_device,
&viper_pcmcia_ops,
sizeof(viper_pcmcia_ops));
if (!ret)
ret = platform_device_add(viper_pcmcia_device);
if (ret)
platform_device_put(viper_pcmcia_device);
return ret;
}
static void __exit viper_pcmcia_exit(void)
{
platform_device_unregister(viper_pcmcia_device);
}
module_init(viper_pcmcia_init);
module_exit(viper_pcmcia_exit);
MODULE_LICENSE("GPL");
Markdown is supported
0% .
You are about to add 0 people to the discussion. Proceed with caution.
先完成此消息的编辑!
想要评论请 注册