superio.c 14.0 KB
Newer Older
L
Linus Torvalds 已提交
1 2 3 4 5 6 7 8 9 10 11 12 13
/*      National Semiconductor NS87560UBD Super I/O controller used in
 *      HP [BCJ]x000 workstations.
 *
 *      This chip is a horrid piece of engineering, and National
 *      denies any knowledge of its existence. Thus no datasheet is
 *      available off www.national.com. 
 *
 *	(C) Copyright 2000 Linuxcare, Inc.
 * 	(C) Copyright 2000 Linuxcare Canada, Inc.
 *	(C) Copyright 2000 Martin K. Petersen <mkp@linuxcare.com>
 * 	(C) Copyright 2000 Alex deVries <alex@onefishtwo.ca>
 *      (C) Copyright 2001 John Marvin <jsm fc hp com>
 *      (C) Copyright 2003 Grant Grundler <grundler parisc-linux org>
14
 *	(C) Copyright 2005 Kyle McMartin <kyle@parisc-linux.org>
15
 *	(C) Copyright 2006 Helge Deller <deller@gmx.de>
L
Linus Torvalds 已提交
16 17 18 19 20 21 22 23 24 25 26 27
 *
 *	This program is free software; you can redistribute it and/or
 *	modify it under the terms of the GNU General Public License as
 *	published by the Free Software Foundation; either version 2 of
 *	the License, or (at your option) any later version.  
 *
 *	The initial version of this is by Martin Peterson.  Alex deVries
 *	has spent a bit of time trying to coax it into working.
 *
 *      Major changes to get basic interrupt infrastructure working to
 *      hopefully be able to support all SuperIO devices. Currently
 *      works with serial. -- John Marvin <jsm@fc.hp.com>
28 29 30
 *
 *	Converted superio_init() to be a PCI_FIXUP_FINAL callee.
 *         -- Kyle McMartin <kyle@parisc-linux.org>
L
Linus Torvalds 已提交
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
 */


/* NOTES:
 * 
 * Function 0 is an IDE controller. It is identical to a PC87415 IDE
 * controller (and identifies itself as such).
 *
 * Function 1 is a "Legacy I/O" controller. Under this function is a
 * whole mess of legacy I/O peripherals. Of course, HP hasn't enabled
 * all the functionality in hardware, but the following is available:
 *
 *      Two 16550A compatible serial controllers
 *      An IEEE 1284 compatible parallel port
 *      A floppy disk controller
 *
 * Function 2 is a USB controller.
 *
 * We must be incredibly careful during initialization.  Since all
 * interrupts are routed through function 1 (which is not allowed by
 * the PCI spec), we need to program the PICs on the legacy I/O port
 * *before* we attempt to set up IDE and USB.  @#$!&
 *
 * According to HP, devices are only enabled by firmware if they have
 * a physical device connected.
 *
 * Configuration register bits:
 *     0x5A: FDC, SP1, IDE1, SP2, IDE2, PAR, Reserved, P92
 *     0x5B: RTC, 8259, 8254, DMA1, DMA2, KBC, P61, APM
 *
 */

#include <linux/errno.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/types.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/serial.h>
#include <linux/pci.h>
#include <linux/parport.h>
#include <linux/parport_pc.h>
#include <linux/termios.h>
#include <linux/tty.h>
#include <linux/serial_core.h>
#include <linux/delay.h>

#include <asm/io.h>
#include <asm/hardware.h>
#include <asm/superio.h>

static struct superio_device sio_dev;


#undef DEBUG_SUPERIO_INIT

#ifdef DEBUG_SUPERIO_INIT
#define DBG_INIT(x...)  printk(x)
#else
#define DBG_INIT(x...)
#endif

93 94 95
#define SUPERIO	"SuperIO"
#define PFX	SUPERIO ": "

L
Linus Torvalds 已提交
96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123
static irqreturn_t
superio_interrupt(int parent_irq, void *devp, struct pt_regs *regs)
{
	u8 results;
	u8 local_irq;

	/* Poll the 8259 to see if there's an interrupt. */
	outb (OCW3_POLL,IC_PIC1+0);

	results = inb(IC_PIC1+0);

	/*
	 * Bit    7:	1 = active Interrupt; 0 = no Interrupt pending
	 * Bits 6-3:	zero
	 * Bits 2-0:	highest priority, active requesting interrupt ID (0-7)
	 */
	if ((results & 0x80) == 0) {
		/* I suspect "spurious" interrupts are from unmasking an IRQ.
		 * We don't know if an interrupt was/is pending and thus
		 * just call the handler for that IRQ as if it were pending.
		 */
		return IRQ_NONE;
	}

	/* Check to see which device is interrupting */
	local_irq = results & 0x0f;

	if (local_irq == 2 || local_irq > 7) {
124
		printk(KERN_ERR PFX "slave interrupted!\n");
L
Linus Torvalds 已提交
125 126 127 128 129 130 131 132 133 134
		return IRQ_HANDLED;
	}

	if (local_irq == 7) {

		/* Could be spurious. Check in service bits */

		outb(OCW3_ISR,IC_PIC1+0);
		results = inb(IC_PIC1+0);
		if ((results & 0x80) == 0) { /* if ISR7 not set: spurious */
135
			printk(KERN_WARNING PFX "spurious interrupt!\n");
L
Linus Torvalds 已提交
136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
			return IRQ_HANDLED;
		}
	}

	/* Call the appropriate device's interrupt */
	__do_IRQ(local_irq, regs);

	/* set EOI - forces a new interrupt if a lower priority device
	 * still needs service.
	 */
	outb((OCW2_SEOI|local_irq),IC_PIC1 + 0);
	return IRQ_HANDLED;
}

/* Initialize Super I/O device */
151 152
static void
superio_init(struct pci_dev *pcidev)
L
Linus Torvalds 已提交
153
{
154
	struct superio_device *sio = &sio_dev;
L
Linus Torvalds 已提交
155 156 157
	struct pci_dev *pdev = sio->lio_pdev;
	u16 word;

H
Helge Deller 已提交
158
	if (sio->suckyio_irq_enabled)
L
Linus Torvalds 已提交
159 160
		return;

161 162
	BUG_ON(!pdev);
	BUG_ON(!sio->usb_pdev);
L
Linus Torvalds 已提交
163 164 165 166 167 168 169

	/* use the IRQ iosapic found for USB INT D... */
	pdev->irq = sio->usb_pdev->irq;

	/* ...then properly fixup the USB to point at suckyio PIC */
	sio->usb_pdev->irq = superio_fixup_irq(sio->usb_pdev);

170
	printk(KERN_INFO PFX "Found NS87560 Legacy I/O device at %s (IRQ %i) \n",
171
	       pci_name(pdev), pdev->irq);
L
Linus Torvalds 已提交
172 173 174

	pci_read_config_dword (pdev, SIO_SP1BAR, &sio->sp1_base);
	sio->sp1_base &= ~1;
175
	printk(KERN_INFO PFX "Serial port 1 at 0x%x\n", sio->sp1_base);
L
Linus Torvalds 已提交
176 177 178

	pci_read_config_dword (pdev, SIO_SP2BAR, &sio->sp2_base);
	sio->sp2_base &= ~1;
179
	printk(KERN_INFO PFX "Serial port 2 at 0x%x\n", sio->sp2_base);
L
Linus Torvalds 已提交
180 181 182

	pci_read_config_dword (pdev, SIO_PPBAR, &sio->pp_base);
	sio->pp_base &= ~1;
183
	printk(KERN_INFO PFX "Parallel port at 0x%x\n", sio->pp_base);
L
Linus Torvalds 已提交
184 185 186

	pci_read_config_dword (pdev, SIO_FDCBAR, &sio->fdc_base);
	sio->fdc_base &= ~1;
187
	printk(KERN_INFO PFX "Floppy controller at 0x%x\n", sio->fdc_base);
L
Linus Torvalds 已提交
188 189
	pci_read_config_dword (pdev, SIO_ACPIBAR, &sio->acpi_base);
	sio->acpi_base &= ~1;
190
	printk(KERN_INFO PFX "ACPI at 0x%x\n", sio->acpi_base);
L
Linus Torvalds 已提交
191 192 193 194 195 196

	request_region (IC_PIC1, 0x1f, "pic1");
	request_region (IC_PIC2, 0x1f, "pic2");
	request_region (sio->acpi_base, 0x1f, "acpi");

	/* Enable the legacy I/O function */
H
Helge Deller 已提交
197
	pci_read_config_word (pdev, PCI_COMMAND, &word);
L
Linus Torvalds 已提交
198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269
	word |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY | PCI_COMMAND_IO;
	pci_write_config_word (pdev, PCI_COMMAND, word);

	pci_set_master (pdev);
	pci_enable_device(pdev);

	/*
	 * Next project is programming the onboard interrupt controllers.
	 * PDC hasn't done this for us, since it's using polled I/O.
	 *
	 * XXX Use dword writes to avoid bugs in Elroy or Suckyio Config
	 *     space access.  PCI is by nature a 32-bit bus and config
	 *     space can be sensitive to that.
	 */

	/* 0x64 - 0x67 :
		DMA Rtg 2
		DMA Rtg 3
		DMA Chan Ctl
		TRIGGER_1    == 0x82   USB & IDE level triggered, rest to edge
	*/
	pci_write_config_dword (pdev, 0x64,         0x82000000U);

	/* 0x68 - 0x6b :
		TRIGGER_2    == 0x00   all edge triggered (not used)
		CFG_IR_SER   == 0x43   SerPort1 = IRQ3, SerPort2 = IRQ4
		CFG_IR_PF    == 0x65   ParPort  = IRQ5, FloppyCtlr = IRQ6
		CFG_IR_IDE   == 0x07   IDE1 = IRQ7, reserved
	*/
	pci_write_config_dword (pdev, TRIGGER_2,    0x07654300U);

	/* 0x6c - 0x6f :
		CFG_IR_INTAB == 0x00
		CFG_IR_INTCD == 0x10   USB = IRQ1
		CFG_IR_PS2   == 0x00
		CFG_IR_FXBUS == 0x00
	*/
	pci_write_config_dword (pdev, CFG_IR_INTAB, 0x00001000U);

	/* 0x70 - 0x73 :
		CFG_IR_USB   == 0x00  not used. USB is connected to INTD.
		CFG_IR_ACPI  == 0x00  not used.
		DMA Priority == 0x4c88  Power on default value. NFC.
	*/
	pci_write_config_dword (pdev, CFG_IR_USB, 0x4c880000U);

	/* PIC1 Initialization Command Word register programming */
	outb (0x11,IC_PIC1+0);	/* ICW1: ICW4 write req | ICW1 */
	outb (0x00,IC_PIC1+1);	/* ICW2: interrupt vector table - not used */
	outb (0x04,IC_PIC1+1);	/* ICW3: Cascade */
	outb (0x01,IC_PIC1+1);	/* ICW4: x86 mode */

	/* PIC1 Program Operational Control Words */
	outb (0xff,IC_PIC1+1);	/* OCW1: Mask all interrupts */
	outb (0xc2,IC_PIC1+0);  /* OCW2: priority (3-7,0-2) */

	/* PIC2 Initialization Command Word register programming */
	outb (0x11,IC_PIC2+0);	/* ICW1: ICW4 write req | ICW1 */
	outb (0x00,IC_PIC2+1);	/* ICW2: N/A */
	outb (0x02,IC_PIC2+1);	/* ICW3: Slave ID code */
	outb (0x01,IC_PIC2+1);	/* ICW4: x86 mode */
		
	/* Program Operational Control Words */
	outb (0xff,IC_PIC1+1);	/* OCW1: Mask all interrupts */
	outb (0x68,IC_PIC1+0);	/* OCW3: OCW3 select | ESMM | SMM */

	/* Write master mask reg */
	outb (0xff,IC_PIC1+1);

	/* Setup USB power regulation */
	outb(1, sio->acpi_base + USB_REG_CR);
	if (inb(sio->acpi_base + USB_REG_CR) & 1)
270
		printk(KERN_INFO PFX "USB regulator enabled\n");
L
Linus Torvalds 已提交
271
	else
272
		printk(KERN_ERR PFX "USB regulator not initialized!\n");
L
Linus Torvalds 已提交
273 274

	if (request_irq(pdev->irq, superio_interrupt, SA_INTERRUPT,
275
			SUPERIO, (void *)sio)) {
L
Linus Torvalds 已提交
276

277
		printk(KERN_ERR PFX "could not get irq\n");
L
Linus Torvalds 已提交
278 279 280 281 282 283
		BUG();
		return;
	}

	sio->suckyio_irq_enabled = 1;
}
284
DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO, superio_init);
L
Linus Torvalds 已提交
285 286 287 288 289 290

static void superio_disable_irq(unsigned int irq)
{
	u8 r8;

	if ((irq < 1) || (irq == 2) || (irq > 7)) {
291
		printk(KERN_ERR PFX "Illegal irq number.\n");
L
Linus Torvalds 已提交
292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307
		BUG();
		return;
	}

	/* Mask interrupt */

	r8 = inb(IC_PIC1+1);
	r8 |= (1 << irq);
	outb (r8,IC_PIC1+1);
}

static void superio_enable_irq(unsigned int irq)
{
	u8 r8;

	if ((irq < 1) || (irq == 2) || (irq > 7)) {
308
		printk(KERN_ERR PFX "Illegal irq number (%d).\n", irq);
L
Linus Torvalds 已提交
309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325
		BUG();
		return;
	}

	/* Unmask interrupt */
	r8 = inb(IC_PIC1+1);
	r8 &= ~(1 << irq);
	outb (r8,IC_PIC1+1);
}

static unsigned int superio_startup_irq(unsigned int irq)
{
	superio_enable_irq(irq);
	return 0;
}

static struct hw_interrupt_type superio_interrupt_type = {
326
	.typename =	SUPERIO,
L
Linus Torvalds 已提交
327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362
	.startup =	superio_startup_irq,
	.shutdown =	superio_disable_irq,
	.enable =	superio_enable_irq,
	.disable =	superio_disable_irq,
	.ack =		no_ack_irq,
	.end =		no_end_irq,
};

#ifdef DEBUG_SUPERIO_INIT
static unsigned short expected_device[3] = {
	PCI_DEVICE_ID_NS_87415,
	PCI_DEVICE_ID_NS_87560_LIO,
	PCI_DEVICE_ID_NS_87560_USB
};
#endif

int superio_fixup_irq(struct pci_dev *pcidev)
{
	int local_irq, i;

#ifdef DEBUG_SUPERIO_INIT
	int fn;
	fn = PCI_FUNC(pcidev->devfn);

	/* Verify the function number matches the expected device id. */
	if (expected_device[fn] != pcidev->device) {
		BUG();
		return -1;
	}
	printk("superio_fixup_irq(%s) ven 0x%x dev 0x%x from %p\n",
		pci_name(pcidev),
		pcidev->vendor, pcidev->device,
		__builtin_return_address(0));
#endif

	for (i = 0; i < 16; i++) {
363
		irq_desc[i].chip = &superio_interrupt_type;
L
Linus Torvalds 已提交
364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395
	}

	/*
	 * We don't allocate a SuperIO irq for the legacy IO function,
	 * since it is a "bridge". Instead, we will allocate irq's for
	 * each legacy device as they are initialized.
	 */

	switch(pcidev->device) {
	case PCI_DEVICE_ID_NS_87415:		/* Function 0 */
		local_irq = IDE_IRQ;
		break;
	case PCI_DEVICE_ID_NS_87560_LIO:	/* Function 1 */
		sio_dev.lio_pdev = pcidev;	/* save for superio_init() */
		return -1;
	case PCI_DEVICE_ID_NS_87560_USB:	/* Function 2 */
		sio_dev.usb_pdev = pcidev;	/* save for superio_init() */
		local_irq = USB_IRQ;
		break;
	default:
		local_irq = -1;
		BUG();
		break;
	}

	return local_irq;
}

static void __devinit superio_serial_init(void)
{
#ifdef CONFIG_SERIAL_8250
	int retval;
396 397 398 399 400 401 402 403 404 405 406 407 408 409
	struct uart_port serial_port;

	memset(&serial_port, 0, sizeof(serial_port));
	serial_port.iotype	= UPIO_PORT;
	serial_port.type	= PORT_16550A;
	serial_port.uartclk	= 115200*16;
	serial_port.fifosize	= 16;
	spin_lock_init(&serial_port.lock);

	/* serial port #1 */
	serial_port.iobase	= sio_dev.sp1_base;
	serial_port.irq		= SP1_IRQ;
	serial_port.line	= 0;
	retval = early_serial_setup(&serial_port);
L
Linus Torvalds 已提交
410
	if (retval < 0) {
411
		printk(KERN_WARNING PFX "Register Serial #0 failed.\n");
L
Linus Torvalds 已提交
412 413 414
		return;
	}

415 416 417 418 419
	/* serial port #2 */
	serial_port.iobase	= sio_dev.sp2_base;
	serial_port.irq		= SP2_IRQ;
	serial_port.line	= 1;
	retval = early_serial_setup(&serial_port);
L
Linus Torvalds 已提交
420
	if (retval < 0)
421
		printk(KERN_WARNING PFX "Register Serial #1 failed.\n");
L
Linus Torvalds 已提交
422 423 424 425 426 427 428 429 430 431 432 433 434
#endif /* CONFIG_SERIAL_8250 */
}


static void __devinit superio_parport_init(void)
{
#ifdef CONFIG_PARPORT_PC
	if (!parport_pc_probe_port(sio_dev.pp_base,
			0 /*base_hi*/,
			PAR_IRQ, 
			PARPORT_DMA_NONE /* dma */,
			NULL /*struct pci_dev* */) )

435
		printk(KERN_WARNING PFX "Probing parallel port failed.\n");
L
Linus Torvalds 已提交
436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452
#endif	/* CONFIG_PARPORT_PC */
}


static void superio_fixup_pci(struct pci_dev *pdev)
{
	u8 prog;

	pdev->class |= 0x5;
	pci_write_config_byte(pdev, PCI_CLASS_PROG, pdev->class);

	pci_read_config_byte(pdev, PCI_CLASS_PROG, &prog);
	printk("PCI: Enabled native mode for NS87415 (pif=0x%x)\n", prog);
}
DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415, superio_fixup_pci);


453 454
static int __devinit
superio_probe(struct pci_dev *dev, const struct pci_device_id *id)
L
Linus Torvalds 已提交
455
{
456
	struct superio_device *sio = &sio_dev;
L
Linus Torvalds 已提交
457 458 459 460 461 462 463 464 465 466 467 468

	/*
	** superio_probe(00:0e.0) ven 0x100b dev 0x2 sv 0x0 sd 0x0 class 0x1018a
	** superio_probe(00:0e.1) ven 0x100b dev 0xe sv 0x0 sd 0x0 class 0x68000
	** superio_probe(00:0e.2) ven 0x100b dev 0x12 sv 0x0 sd 0x0 class 0xc0310
	*/
	DBG_INIT("superio_probe(%s) ven 0x%x dev 0x%x sv 0x%x sd 0x%x class 0x%x\n",
		pci_name(dev),
		dev->vendor, dev->device,
		dev->subsystem_vendor, dev->subsystem_device,
		dev->class);

469
	BUG_ON(!sio->suckyio_irq_enabled);	/* Enabled by PCI_FIXUP_FINAL */
L
Linus Torvalds 已提交
470 471 472 473 474 475 476 477 478 479 480 481 482 483

	if (dev->device == PCI_DEVICE_ID_NS_87560_LIO) {	/* Function 1 */
		superio_parport_init();
		superio_serial_init();
		/* REVISIT XXX : superio_fdc_init() ? */
		return 0;
	} else if (dev->device == PCI_DEVICE_ID_NS_87415) {	/* Function 0 */
		DBG_INIT("superio_probe: ignoring IDE 87415\n");
	} else if (dev->device == PCI_DEVICE_ID_NS_87560_USB) {	/* Function 2 */
		DBG_INIT("superio_probe: ignoring USB OHCI controller\n");
	} else {
		DBG_INIT("superio_probe: WTF? Fire Extinguisher?\n");
	}

484
	/* Let appropriate other driver claim this device. */
L
Linus Torvalds 已提交
485 486 487 488
	return -ENODEV;
}

static struct pci_device_id superio_tbl[] = {
489 490 491
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_LIO) },
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87560_USB) },
	{ PCI_DEVICE(PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_87415) },
L
Linus Torvalds 已提交
492 493 494 495
	{ 0, }
};

static struct pci_driver superio_driver = {
496
	.name =         SUPERIO,
497 498
	.id_table =     superio_tbl,
	.probe =        superio_probe,
L
Linus Torvalds 已提交
499 500 501 502 503 504 505 506 507 508 509 510 511 512
};

static int __init superio_modinit(void)
{
	return pci_register_driver(&superio_driver);
}

static void __exit superio_exit(void)
{
	pci_unregister_driver(&superio_driver);
}

module_init(superio_modinit);
module_exit(superio_exit);