We need to bump to CentOS 7 before we can undo this, because Red Hat
ships very old compilers :(

* Remove DDBoost Full and Incremental backup/restore TINC jobs
* Add behave backup/restore DDBoost job

The previous job took 3h, 50 mins and the new job takes 1h, 20 mins.

These tests were used to test backup/restore on Data Domain. They have
been replaced with behave tests.
Signed-off-by: NJamie McAtamney <jmcatamney@pivotal.io>

This is part of the effort to unify our backup/restore tests into a
single suite.

* Adds infrastructure to setup DDBoost on the client and cleanup server
* after completion
* Adds tests for DDBoost specific options
* Adds test coverage from TINC suite that was not included in behave
Signed-off-by: NChris Hajas <chajas@pivotal.io>

A test output in extprotocol is undeterministic in which case all
segments will report an error, you can not tell which segment will
report it firstly. Normally it's segment 0 first report that, but we
can not count on this.

Make sliceIndex, rootIndex, parentIndex and children near each other to see
slice debug output info easily.

Formerly, GPDB do dispatch/interconnect cleanup on executor level
which means once an error occurs within executor, it will be catched and
dispatch/interconnect will be cleaned. The problem is if an error occurs
after an executor started but before the executor run, dispatch/interconnect
has no chance to be cleaned up. A problem is that outbound UDP interconnect
packets still think the interconnect is active and will access the
memory that has been freed.

This commit add a few cleanup points on portal level, a higher call level
than executor to cover more cases shown as above. mppExecutorCleanup() is
reentrant, so it's ok to do double check on both level.

This statistic info is convenient for debugging and test cases

This reverts commit 9bea5037.

Formerly, GPDB do dispatch/interconnect cleanup on executor level
which means once an error occurs within executor, it will be catched and
dispatch/interconnect will be cleaned. The problem is if an error occurs
after an executor started but before the executor run, dispatch/interconnect
has no chance to be cleaned up. A problem is that outbound UDP interconnect
packets still think the interconnect is active and will access the
memory that has been freed.

This commit add a few cleanup points on portal level, a higher call level
than executor to cover more cases shown as above. mppExecutorCleanup() is
reentrant, so it's ok to do double check on both level.

Since Command creates a short-lived SSH session, we observe the PID given
a throw-away remote process. Assume that the PID is unused and available on
the remote in the near future.

This pid is no longer associated with a
running process and won't be recycled for long enough that tests
have finished.

Looking ahead introduces the risk of a time-of-check-time-of-use race
since the pid might have been allocated by the operating system by
the time the test would use the data.

because it was causing storage/basic/lock TINC test to fail.

This reverts commit 243121f9.

Signed-off-by: NTushar Dadlani <tdadlani@pivotal.io>

Signed-off-by: NLarry Hamel <lhamel@pivotal.io>

Signed-off-by: NTushar Dadlani <tdadlani@pivotal.io>

* docs: correct the gpperfmon_install command syntax

* Correct gpperfmon_install command syntax in help text

* Remove references to SHA-256-FIPS

* gpperfmon_install docs: Clarify options syntax
Signed-off-by: NC.J. Jameson <cjameson@pivotal.io>

In Orca, motion node used to assign it's child node with FLOW_SINGLETON if
the child has only one sender, it works fine for multiple segments cluster,
but for single segment cluster, all gangs that supposed to be GANGTYPE_PRIM
ARY_READER/WRITER now become GANGTYPE_ENTRYDB_READER or GANGTYPE_SINGLETON_READER,
no primary reader or writer gangs are created. A typical bug of this is
singleton/entry-db readers will get stuck in obtaining shared snapshot that should
have been created by writer gang.

This commit fixes #2121, it takes one segment cluster into consideration and assigns flow type more accurately.

* Make the 10 Gb optional

Original deadlock is caused by a reader waiting on a lock which is already held
by the writer of the same MPP session, and another session is waiting for a
conflicting mode on the same lock.

The fix is to avoid checking waitMask conflicts for reader (i.e. MyProc is
different from lockHolderProcPtr).

Detailed discussion of the deadlock issue is at:
https://groups.google.com/a/greenplum.org/d/msg/gpdb-dev/OS1-ODIK0P4/ZIzayBbMBwAJ

Two isloation2 tests are added.  One to validate the deadlock does not occur
and another to ensure that granting locks to readers does not starve existing
waiters.
Signed-off-by: NXin Zhang <xzhang@pivotal.io>

The xmloption support for preserving whitespace was enabled in a
previous commit, bump the feature compliance table to reflect the
status of the code.

- Only difference is `#if 0` / `#endif` around the whole file so that
it's clear to developer utilities that these aren't compiled in

Partially addresses https://github.com/greenplum-db/gpdb/issues/2422Signed-off-by: NTodd Sedano <professor@gmail.com>
Signed-off-by: NChris Hajas <chajas@pivotal.io>

* Make the note about million files more explicit

gpmondb.c CID 160656: Resource leak in gpdb_check_partitions(). An early
return meant that the connection was not always closed. Hence, calculate
the return value, close the connection, then return.

gpmon_agg.c CID 160655: Resource leak in write_dbmetrics(). Files were
not being closed if dbmetrics were too long. Hence, fix the case where
early return means files don't get closed.

gpmondb.c CID 160654: Resource leak in gpdb_exec(). The pconn passed in
was not always getting a PGconn assigned to it. But returning a failed
connection and letting the caller of gpdb_exec clean it up is the usage
pattern. Hence, always make the conn available before returning.

gpmmon.c CID 160653: removed as part of remove_iterators work.

gpmon_agg.c CID 160652: duplicate of CID 160655
Signed-off-by: NLarry Hamel <lhamel@pivotal.io>
Signed-off-by: NC.J. Jameson <cjameson@pivotal.io>

Signed-off-by: NNadeem Ghani <nghani@pivotal.io>

Signed-off-by: NLarry Hamel <lhamel@pivotal.io>

* Update HA documentation

Mirrors must reside on different storage systems too.
Master fail-over must be triggered externally.
10-Gb Ethernet is optional.

Under former TCP interconnect, after declaring a cursor for an invalid
query like "declare c1 cursor for select c1/0 from foo", the following FETCH
command can still fetch an empty row instead of an error. This is
incorrect and does not consist with UDP interconnect.

The RCA is senders of TCP interconnect always send an EOF message to
their peers regardless of the errors on segments, so the receivers can
not tell the difference of EOF or an error.

The solution in this commit is do not send the EOF to the peers if senders is
encountering an error and let the QD to check the whole segments status when it
can not read data from interconnect for a long time.

This commit restore TCP interconnect and fix some hang issues.

* restore TCP interconnect code
* Add GUC called gp_interconnect_tcp_listener_backlog for tcp to control the backlog param of listen call
* use memmove instead of memcpy because the memory areas do overlap.
* call checkForCancelFromQD() for TCP interconnect if there are no data for a while, this can avoid QD from getting stuck.
* revert cancelUnfinished related modification in 8d251945, otherwise some queries will get stuck
* move and rename faultinjector "cursor_qe_reader_after_snapshot" to make test cases pass under TCP interconnect.

* Change the default level of gp_log_gang to off.
* Log the query plan size in level TERSE, it's useful for debugging.

It is insecurity to run priviledged containers on public pipelines, so
disable resource group jobs until a new priviledged VM mechanism can be
provided.

Signed-off-by: NTushar Dadlani <tdadlani@pivotal.io>

Adding tests to show that minimal functionality of gpcheck works.

gpcheck checks for specific system requirements. As such, we had to add
system configuration changes to control files at test runtime prior to
behave.

We explored running some tests as root to more realistically test how
gpcheck is used, but don't have that at this time.

Also adding back gpcheck_hostdump which is called by
gpcheck.
Signed-off-by: NTushar Dadlani <tdadlani@pivotal.io>

Signed-off-by: NMelanie Plageman <mplageman@pivotal.io>