- 27 11月, 2008 1 次提交
-
-
The inode table has been zeroed in setup_new_group_blocks(). Mark it as such in ext4_group_add(). Since we are currently clearing inode table for the new block group, we should set the EXT4_BG_INODE_ZEROED flag. If at some point in the future we don't immediately zero out the inode table as part of the resize operation, then obviously we shouldn't do this. Signed-off-by: Solofo.Ramangalahy@bull.net Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 10 10月, 2008 1 次提交
-
-
由 Theodore Ts'o 提交于
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 08 9月, 2008 1 次提交
-
-
由 Frederic Bohe 提交于
This fixes a bug which prevented the newly created inodes after a resize from being used on filesystems with flex_bg. Signed-off-by: NFrederic Bohe <frederic.bohe@bull.net> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 09 9月, 2008 1 次提交
-
-
由 Theodore Ts'o 提交于
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 20 8月, 2008 1 次提交
-
-
由 Josef Bacik 提交于
When trying to resize an ext4 fs and you run out of reserved gdt blocks, you get an error that doesn't actually tell you what went wrong, it just says that the gdb it picked is not correct, which is the case since you don't have any reserved gdt blocks left. This patch adds a check to make sure you have reserved gdt blocks to use, and if not prints out a more relevant error. Signed-off-by: NJosef Bacik <jbacik@redhat.com> Cc: <linux-ext4@vger.kernel.org> Cc: Andreas Dilger <adilger@sun.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 27 7月, 2008 1 次提交
-
-
由 Theodore Ts'o 提交于
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 12 7月, 2008 1 次提交
-
-
由 Frederic Bohe 提交于
Update group infos when updating a group's descriptor. Add group infos when adding a group's descriptor. Refresh cache pages used by mb_alloc when changes occur. This will probably need modifications when META_BG resizing will be allowed. Signed-off-by: NFrederic Bohe <frederic.bohe@bull.net> Signed-off-by: NMingming Cao <cmm@us.ibm.com>
-
- 20 6月, 2008 1 次提交
-
-
由 Frederic Bohe 提交于
This is the patch for the group descriptor table corruption during online resize pointed out by Theodore Tso. The problem was caused by the fact that the ext4 group descriptor can be either 32 or 64 bytes long. Only the 64 bytes structure was taken into account. Signed-off-by: NFrederic Bohe <frederic.bohe@bull.net> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 07 6月, 2008 1 次提交
-
-
由 Josef Bacik 提交于
There is a bug when we are trying to verify that the reserve inode's double indirect blocks point back to the primary gdt blocks. The fix is obvious, we need to mod the gdb count by the addr's per block. This was verified using the same testcase as with the ext3 equivalent of this patch. Signed-off-by: NJosef Bacik <jbacik@redhat.com> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 30 4月, 2008 2 次提交
-
-
由 Christoph Hellwig 提交于
Move ext4 headers out of include/linux. This is just the trivial move, there's some more thing that could be done later. Signed-off-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
由 Josef Bacik 提交于
This fixes the allocations with GFP_KERNEL while under a transaction problems in ext4. This patch is the same as its ext3 counterpart, just switches these to GFP_NOFS. Signed-off-by: NJosef Bacik <jbacik@redhat.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
- 17 4月, 2008 2 次提交
-
-
由 Harvey Harrison 提交于
__FUNCTION__ is gcc-specific, use __func__ Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Cc: <linux-ext4@vger.kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
-
由 Marcin Slusarz 提交于
replace all: little_endian_variable = cpu_to_leX(leX_to_cpu(little_endian_variable) + expression_in_cpu_byteorder); with: leX_add_cpu(&little_endian_variable, expression_in_cpu_byteorder); generated with semantic patch Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu> Cc: linux-ext4@vger.kernel.org Cc: sct@redhat.com Cc: Andrew Morton <akpm@linux-foundation.org> Cc: adilger@clusterfs.com Cc: Mingming Cao <cmm@us.ibm.com>
-
- 26 2月, 2008 1 次提交
-
-
由 Akinobu Mita 提交于
Add missing ext4_journal_stop() in error handling. Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com> Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu> Cc: Stephen Tweedie <sct@redhat.com> Cc: adilger@clusterfs.com Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Mingming Cao <cmm@us.ibm.com>
-
- 08 2月, 2008 1 次提交
-
-
由 David Howells 提交于
Stop the EXT4 filesystem from using iget() and read_inode(). Replace ext4_read_inode() with ext4_iget(), and call that instead of iget(). ext4_iget() then uses iget_locked() directly and returns a proper error code instead of an inode in the event of an error. ext4_fill_super() returns any error incurred when getting the root inode instead of EINVAL. Signed-off-by: NDavid Howells <dhowells@redhat.com> Acked-by: N"Theodore Ts'o" <tytso@mit.edu> Acked-by: NJan Kara <jack@suse.cz> Cc: <linux-ext4@vger.kernel.org> Acked-by: NChristoph Hellwig <hch@lst.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 29 1月, 2008 2 次提交
-
-
由 Eric Sandeen 提交于
Builds with EXT4FS_DEBUG defined (to enable ext4_debug()) fail without these changes. Clean up some format warnings too. Signed-off-by: NEric Sandeen <sandeen@redhat.com> Signed-off-by: NMingming Cao <cmm@us.ibm.com>
-
由 Avantika Mathur 提交于
In many places variables for block group are of type int, which limits the maximum number of block groups to 2^31. Each block group can have up to 2^15 blocks, with a 4K block size, and the max filesystem size is limited to 2^31 * (2^15 * 2^12) = 2^58 -- or 256 PB This patch introduces a new type ext4_group_t, of type unsigned long, to represent block group numbers in ext4. All occurrences of block group variables are converted to type ext4_group_t. Signed-off-by: NAvantika Mathur <mathur@us.ibm.com>
-
- 18 10月, 2007 3 次提交
-
-
由 Eric Sandeen 提交于
When resizing online, setup_new_group_blocks attempts to reserve a potentially very large transaction, depending on the current filesystem geometry. For some journal sizes, there may not be enough room for this transaction, and the online resize will fail. The patch below resizes & restarts the transaction as necessary while setting up the new group, and should work with even the smallest journal. Tested with something like: [root@newbox ~]# dd if=/dev/zero of=fsfile bs=1024 count=32768 [root@newbox ~]# mkfs.ext3 -b 1024 fsfile 16384 [root@newbox ~]# mount -o loop fsfile mnt/ [root@newbox ~]# resize2fs /dev/loop0 resize2fs 1.40.2 (12-Jul-2007) Filesystem at /dev/loop0 is mounted on /root/mnt; on-line resizing required old desc_blocks = 1, new_desc_blocks = 1 Performing an on-line resize of /dev/loop0 to 32768 (1k) blocks. resize2fs: No space left on device While trying to add group #2 [root@newbox ~]# dmesg | tail -n 1 JBD: resize2fs wants too many credits (258 > 256) [root@newbox ~]# With the below change, it works. Signed-off-by: NEric Sandeen <sandeen@redhat.com> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Acked-by: NAndreas Dilger <adilger@clusterfs.com>
-
由 Eric Sandeen 提交于
setup_new_group_blocks() manipulates the group descriptor block bh under the block_bitmap bh's lock. It shouldn't matter since nobody but resize should be touching these blocks, but it's worth fixing up. Signed-off-by: NEric Sandeen <sandeen@redhat.com> Signed-off-by: NMingming Cao <cmm@us.ibm.com>
-
由 Andreas Dilger 提交于
In pass1 of e2fsck, every inode table in the fileystem is scanned and checked, regardless of whether it is in use. This is this the most time consuming part of the filesystem check. The unintialized block group feature can greatly reduce e2fsck time by eliminating checking of uninitialized inodes. With this feature, there is a a high water mark of used inodes for each block group. Block and inode bitmaps can be uninitialized on disk via a flag in the group descriptor to avoid reading or scanning them at e2fsck time. A checksum of each group descriptor is used to ensure that corruption in the group descriptor's bit flags does not cause incorrect operation. The feature is enabled through a mkfs option mke2fs /dev/ -O uninit_groups A patch adding support for uninitialized block groups to e2fsprogs tools has been posted to the linux-ext4 mailing list. The patches have been stress tested with fsstress and fsx. In performance tests testing e2fsck time, we have seen that e2fsck time on ext3 grows linearly with the total number of inodes in the filesytem. In ext4 with the uninitialized block groups feature, the e2fsck time is constant, based solely on the number of used inodes rather than the total inode count. Since typical ext4 filesystems only use 1-10% of their inodes, this feature can greatly reduce e2fsck time for users. With performance improvement of 2-20 times, depending on how full the filesystem is. The attached graph shows the major improvements in e2fsck times in filesystems with a large total inode count, but few inodes in use. In each group descriptor if we have EXT4_BG_INODE_UNINIT set in bg_flags: Inode table is not initialized/used in this group. So we can skip the consistency check during fsck. EXT4_BG_BLOCK_UNINIT set in bg_flags: No block in the group is used. So we can skip the block bitmap verification for this group. We also add two new fields to group descriptor as a part of uninitialized group patch. __le16 bg_itable_unused; /* Unused inodes count */ __le16 bg_checksum; /* crc16(sb_uuid+group+desc) */ bg_itable_unused: If we have EXT4_BG_INODE_UNINIT not set in bg_flags then bg_itable_unused will give the offset within the inode table till the inodes are used. This can be used by fsck to skip list of inodes that are marked unused. bg_checksum: Now that we depend on bg_flags and bg_itable_unused to determine the block and inode usage, we need to make sure group descriptor is not corrupt. We add checksum to group descriptor to detect corruption. If the descriptor is found to be corrupt, we mark all the blocks and inodes in the group used. Signed-off-by: NAvantika Mathur <mathur@us.ibm.com> Signed-off-by: NAndreas Dilger <adilger@clusterfs.com> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
-
- 17 10月, 2007 1 次提交
-
-
由 Peter Zijlstra 提交于
s/percpu_counter_mod/percpu_counter_add/ Because its a better name, _mod implies modulo. Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 09 5月, 2007 1 次提交
-
-
由 Randy Dunlap 提交于
Remove includes of <linux/smp_lock.h> where it is not used/needed. Suggested by Al Viro. Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc, sparc64, and arm (all 59 defconfigs). Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 15 2月, 2007 1 次提交
-
-
由 Tim Schmielau 提交于
After Al Viro (finally) succeeded in removing the sched.h #include in module.h recently, it makes sense again to remove other superfluous sched.h includes. There are quite a lot of files which include it but don't actually need anything defined in there. Presumably these includes were once needed for macros that used to live in sched.h, but moved to other header files in the course of cleaning it up. To ease the pain, this time I did not fiddle with any header files and only removed #includes from .c-files, which tend to cause less trouble. Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha, arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig, allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all configs in arch/arm/configs on arm. I also checked that no new warnings were introduced by the patch (actually, some warnings are removed that were emitted by unnecessarily included header files). Signed-off-by: NTim Schmielau <tim@physik3.uni-rostock.de> Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 29 10月, 2006 1 次提交
-
-
由 Randy Dunlap 提交于
fs/ext4/resize.c:72: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:76: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:81: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:85: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:89: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:89: warning: long long unsigned int format, __u64 arg (arg 5) fs/ext4/resize.c:93: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:93: warning: long long unsigned int format, __u64 arg (arg 5) fs/ext4/resize.c:98: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:103: warning: long long unsigned int format, __u64 arg (arg 4) fs/ext4/resize.c:109: warning: long long unsigned int format, __u64 arg (arg 4) Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 12 10月, 2006 7 次提交
-
-
由 Alexandre Ratchov 提交于
move '_hi' bits of block numbers in the larger part of the block group descriptor structure Signed-off-by: NAlexandre Ratchov <alexandre.ratchov@bull.net> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
Change ext4 in-kernel block type (ext4_fsblk_t) from sector_t to unsigned long long. Remove ext4 block type string micro E3FSBLK, replaced with "%llu" [akpm@osdl.org: build fix] Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Laurent Vivier 提交于
In-kernel super block changes to support >32 bit free blocks numbers. Signed-off-by: NLaurent Vivier <Laurent.Vivier@bull.net> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAlexandre Ratchov <alexandre.ratchov@bull.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
Redefine ext3 in-kernel filesystem block type (ext3_fsblk_t) from unsigned long to sector_t, to allow kernel to handle >32 bit ext3 blocks. Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
Reworked from a patch by Mingming Cao and Randy Dunlap Signed-off-By: NRandy Dunlap <rdunlap@xenotime.net> Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
Mingming Cao originally did this work, and Shaggy reproduced it using some scripts from her. Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Dave Kleikamp 提交于
Start of the ext4 patch series. See Documentation/filesystems/ext4.txt for details. This is a simple copy of the files in fs/ext3 to fs/ext4 and /usr/incude/linux/ext3* to /usr/include/ex4* Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 27 9月, 2006 3 次提交
-
-
由 Panagiotis Issaris 提交于
* Removing useless casts * Removing useless wrapper * Conversion from kmalloc+memset to kzalloc Signed-off-by: NPanagiotis Issaris <takis@issaris.org> Acked-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Eric Sandeen 提交于
Some of the changes in balloc.c are just cosmetic, as Andreas pointed out - if they overflow they'll then underflow and things are fine. 5th hunk actually fixes an overflow problem. Also check for potential overflows in inode & block counts when resizing. Signed-off-by: NEric Sandeen <esandeen@redhat.com> Cc: Mingming Cao <cmm@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Dave Kleikamp 提交于
Fixing up some endian-ness warnings in preparation to clone ext4 from ext3. Signed-off-by: NDave Kleikamp <shaggy@austin.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 01 7月, 2006 1 次提交
-
-
由 Jörn Engel 提交于
Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: NAdrian Bunk <bunk@stusta.de>
-
- 26 6月, 2006 3 次提交
-
-
由 Mingming Cao 提交于
Convert the ext3 in-kernel filesystem blocks to ext3_fsblk_t. Convert the rest of all unsigned long type in-kernel filesystem blocks to ext3_fsblk_t, and replace the printk format string respondingly. Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
Some of the in-kernel ext3 block variable type are treated as signed 4 bytes int type, thus limited ext3 filesystem to 8TB (4kblock size based). While trying to fix them, it seems quite confusing in the ext3 code where some blocks are filesystem-wide blocks, some are group relative offsets that need to be signed value (as -1 has special meaning). So it seem saner to define two types of physical blocks: one is filesystem wide blocks, another is group-relative blocks. The following patches clarify these two types of blocks in the ext3 code, and fix the type bugs which limit current 32 bit ext3 filesystem limit to 8TB. With this series of patches and the percpu counter data type changes in the mm tree, we are able to extend exts filesystem limit to 16TB. This work is also a pre-request for the recent >32 bit ext3 work, and makes the kernel to able to address 48 bit ext3 block a lot easier: Simply redefine ext3_fsblk_t from unsigned long to sector_t and redefine the format string for ext3 filesystem block corresponding. Two RFC with a series patches have been posted to ext2-devel list and have been reviewed and discussed: http://marc.theaimsgroup.com/?l=ext2-devel&m=114722190816690&w=2 http://marc.theaimsgroup.com/?l=ext2-devel&m=114784919525942&w=2 Patches are tested on both 32 bit machine and 64 bit machine, <8TB ext3 and >8TB ext3 filesystem(with the latest to be released e2fsprogs-1.39). Tests includes overnight fsx, tiobench, dbench and fsstress. This patch: Defines ext3_fsblk_t and ext3_grpblk_t, and the printk format string for filesystem wide blocks. This patch classifies all block group relative blocks, and ext3_fsblk_t blocks occurs in the same function where used to be confusing before. Also include kernel bug fixes for filesystem wide in-kernel block variables. There are some fileystem wide blocks are treated as int/unsigned int type in the kernel currently, especially in ext3 block allocation and reservation code. This patch fixed those bugs by converting those variables to ext3_fsblk_t(unsigned long) type. Signed-off-by: NMingming Cao <cmm@us.ibm.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Mingming Cao 提交于
If ext3 filesystem is larger than 2TB, and sector_t is a u32 (i.e. CONFIG_LBD not defined in the kernel), the calculation of the disk sector will overflow. Add check at ext3_fill_super() and ext3_group_extend() to prevent mount/remount/resize >2TB ext3 filesystem if sector_t size is 4 bytes. Verified this patch on a 32 bit platform without CONFIG_LBD defined (sector_t is 32 bits long), mount refuse to mount a 10TB ext3. Signed-off-by: Mingming Cao<cmm@us.ibm.com> Acked-by: NAndreas Dilger <adilger@clusterfs.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 01 6月, 2006 1 次提交
-
-
由 Andrew Morton 提交于
From: Andrew Morton <akpm@osdl.org> Spotted by Jan Capek <jca@sysgo.com> Cc: "Stephen C. Tweedie" <sct@redhat.com> Cc: Andreas Dilger <adilger@clusterfs.com> Cc: Jan Capek <jca@sysgo.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 26 4月, 2006 1 次提交
-
-
由 Al Viro 提交于
sbi->s_group_desc is an array of pointers to buffer_head. memcpy() of buffer size from address of buffer_head is a bad idea - it will generate junk in any case, may oops if buffer_head is close to the end of slab page and next page is not mapped and isn't what was intended there. IOW, ->b_data is missing in that call. Fortunately, result doesn't go into the primary on-disk data structures, so only backup ones get crap written to them; that had allowed this bug to remain unnoticed until now. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-