If a board isn't using twl4030, then dtc will complain about the missing
phandle (which is in twl4030.dtsi).  Move the phy declaration to the dts
files.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define VDD1 regulator in twl4030 DT and mark it as the supply for the
various OMAP34xx/35xx/36xx/37xx platforms (all use TWL4030 variants with
VDD1 supplying the CPU).

NOTE: This currently will use I2C1 bus communication path to set the
voltage in device tree boot. In the legacy non device tree boot, we
continue to use twl-common.c which bypasses I2C1 bus communication path
and uses I2C4 bus path using OMAP voltage libraries. We should
eventually be able to use I2C4 path once we have voltage regulator for
OMAP which is capable of using the voltage controller/voltage processor
IP blocks.
Signed-off-by: NNishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add usb otg data node in omap4/omap3 device tree file. Also update
the node with board specific setting in omapx-<board>.dts file.
The dt data specifies among others the interface type (ULPI or UTMI),
mode which is mostly OTG, power that specifies the amount of power
this can supply when in host mode.

The information about usb otg node is available @
Documentation/devicetree/bindings/usb/omap-usb.txt
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a minimal dts for original OMAP3430/3530 version of the Beagle board. This
version of the Beagle board has 256MB of DDR and features the same TWL4030
power management IC (PMIC) as the Beagle board XM.

Given that the Beagle and Beagle-XM boards use the same PMIC, move the
definition of the VSIM regulator into the TWL4030.dtsi file so that we do not
need to duplicate in the Beagle board dts file.

This has been boot tested on an OMAP3530 Beagle board and verifing that the
SD/MMC interface is working with a SD card.

V2 changes
- Rebased upon of devel-dt
- Corrected copyright date in omap3-beagle.dts file
- Added LED support after verifing that Beagle and Beagle XM have the same LED
  configuration
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

The extra serial port is not available on 34xx. And the current
omap3-beagle.dts file is for omap3-beagle-xm.dts as it lists 512MB
of memory.

Please somebody submit a new omap3-beagle.dts for the original 34xx
BeagleBoard after testing it properly.

Cc: Benoit Cousson <b-cousson@ti.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the needed sections to enable audio support on BeagleBoard when booted
with DT blob.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add the support for D6 and D7 LEDs on Beagle board.
- D6 will be used for heartbeat
- D7 will be used for mmc0
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add device tree properties for twl4030/gpio, according to the
platform data of corresponding boards. This enables the led
connected to LEDB output for both boards, as well as
pullups/pulldowns on GPIO for the BeagleBoard.
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NVaibhav Hiremath <hvaibhav@ti.com>

regulators do not have a 'reg' property, hence the regulator@0,
regulator@1 do not make sense. get rid of it.
Reported-by: NDavid Brown <davidb@codeaurora.org>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.

Just the OMAP part here, the rest goes via other patches and trees.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add OMAP mmc related device tree data for OMAP3.
Currenly limited to only omap3-beagle board.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Pass all the voltage regulator information for
twl6030/twl4030 PMIC from device tree.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add required clock frequencies for the i2c client devices existing
on beagle board.

Add the twl4030 basic description with only the twl_rtc module.

Add the EEPROM node.

Based on original patch from Manju:
http://www.spinics.net/lists/linux-omap/msg55831.htmlSigned-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Since 3.2, the CONFIG_ARM_ATAG_DTB_COMPAT config allows
an old bootloader to still use ATAG to provide cmdline.

Remove chosen/bootargs from the DTS board files.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add OMAP3 beagleboard DTS file to use the omap3.dtsi SoC file.

Add a default bootargs line to allow a boot from RAMDISK.

Add memory node information.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html

Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>