Refactor out the code issue, wait for, and parse the event completion code
for a configure endpoint command.  Modify it to support the evaluate
context command, which has a very similar submission process.  Add
functions to copy parts of the output context into the input context
(which will be used in the evaluate context command).
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the virtual address of the memory hardware uses, not the address for
the container of that memory.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Different sections of the xHCI 0.95 specification had opposing
requirements for the chain bit in a link transaction request buffer (TRB).
The chain bit is used to designate that adjacent TRBs are all part of the
same scatter gather list that should be sent to the device.  Link TRBs can
be in the middle, or at the beginning or end of these chained TRBs.

Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the
chain bit set to 1", meaning it is always chained to the next TRB.
However, section 4.6.9 on the stop endpoint command has specific cases for
what the hardware must do for a link TRB with the chain bit set to 0.  The
0.96 specification errata later cleared up this issue by fixing the
4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain
bit set to 1 or 0.

The problem is that the xHCI cancellation code depends on the chain bit of
the link TRB being cleared when it's at the end of a TD, and some 0.95
xHCI hardware simply stops processing the ring when it encounters a link
TRB with the chain bit cleared.

Allow users who are testing 0.95 xHCI prototypes to set a module parameter
(link_quirk) to turn on this link TRB work around.  Cancellation may not
work if the ring is stopped exactly on a link TRB with chain bit set, but
cancellation should be a relatively uncommon case.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Detect the UART on interface1 and blacklist interface0 (as that is the
JTAG port).
Signed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

SL811 Device detected after removal used to be working in linux-2.6.22
but then broke somewhere between 2.6.22 and 2.6.28. Current
hub_port_connect_change() in drivers/usb/core/hub.c won't call
usb_disconnect() in case the SL811 driver sets portstatus
USB_PORT_FEAT_CONNECTION upon removal.
AFAIK the SL811 has only a combined Device Insert/Remove
detection bit, therefore use a count to distinguish insert or remove.
Signed-Off-By: NMichael Hennerich <hennerich@blackfin.uclinux.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some devices from the OpenDCC project are missing in the list
of the FTDI PIDs. These PIDs are listed at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
(Sorry for the german only page.)
This patch adds the three missing devices.
Signed-off-by: NRainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cdc-acm needs to set a flag during open to tell the
tty layer that the device is initialized
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Paul Martin <pm@debian.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

support for O_NONBLOCK in read and write path
by simply not waiting for data in read or availability
of the write urb in write but returning -EAGAIN
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Tested-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ID for Telit UC-864G GPS/UMTS/WCDMA modem and GPS receiver
to the option driver.
Signed-off-by: NManuel Lauss <manuel.lauss@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A few days ago i got the latest ZTE EVDO modem shown at:
http://img.alibaba.com/photo/240150115/ZTE_AC2726_EVDO_USB_Data_Modem.jpg

It seems that the latest kernel does not have support for it.
I wrote a small patch for the options.c module to add the relevant usb
ids to it.

From: Huzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Sanwa PC5000
mulitimeter with linux.
Signed-off-by: NPawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I'd like to present my small patch enabling to use Hameg HM8143 programmable
power supply with linux.
Signed-off-by: NPawel Ludwikow <pludwiko@rab.ict.pwr.wroc.pl>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the resume path of a block driver GFP_NOIO must be used to
avoid a possible deadlock. The onetouch subdriver of storage violates
the requirement.
Signed-off-by: NOliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf_event, powerpc: Fix compilation after big perf_counter rename

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vegard/kmemcheck:
  kmemcheck: add missing braces to do-while in kmemcheck_annotate_bitfield
  kmemcheck: update documentation
  kmemcheck: depend on HAVE_ARCH_KMEMCHECK
  kmemcheck: remove useless check
  kmemcheck: remove duplicated #include

* 'for-2.6.32' of git://linux-nfs.org/~bfields/linux: (68 commits)
  nfsd4: nfsv4 clients should cross mountpoints
  nfsd: revise 4.1 status documentation
  sunrpc/cache: avoid variable over-loading in cache_defer_req
  sunrpc/cache: use list_del_init for the list_head entries in cache_deferred_req
  nfsd: return success for non-NFS4 nfs4_state_start
  nfsd41: Refactor create_client()
  nfsd41: modify nfsd4.1 backchannel to use new xprt class
  nfsd41: Backchannel: Implement cb_recall over NFSv4.1
  nfsd41: Backchannel: cb_sequence callback
  nfsd41: Backchannel: Setup sequence information
  nfsd41: Backchannel: Server backchannel RPC wait queue
  nfsd41: Backchannel: Add sequence arguments to callback RPC arguments
  nfsd41: Backchannel: callback infrastructure
  nfsd4: use common rpc_cred for all callbacks
  nfsd4: allow nfs4 state startup to fail
  SUNRPC: Defer the auth_gss upcall when the RPC call is asynchronous
  nfsd4: fix null dereference creating nfsv4 callback client
  nfsd4: fix whitespace in NFSPROC4_CLNT_CB_NULL definition
  nfsd41: sunrpc: add new xprt class for nfsv4.1 backchannel
  sunrpc/cache: simplify cache_fresh_locked and cache_fresh_unlocked.
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
  trivial: fix typo in aic7xxx comment
  trivial: fix comment typo in drivers/ata/pata_hpt37x.c
  trivial: typo in kernel-parameters.txt
  trivial: fix typo in tracing documentation
  trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
  trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
  trivial: remove unnecessary semicolons
  trivial: Fix duplicated word "options" in comment
  trivial: kbuild: remove extraneous blank line after declaration of usage()
  trivial: improve help text for mm debug config options
  trivial: doc: hpfall: accept disk device to unload as argument
  trivial: doc: hpfall: reduce risk that hpfall can do harm
  trivial: SubmittingPatches: Fix reference to renumbered step
  trivial: fix typos "man[ae]g?ment" -> "management"
  trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
  trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
  trivial: fix missing printk space in amd_k7_smp_check
  trivial: fix typo s/ketymap/keymap/ in comment
  trivial: fix typo "to to" in multiple files
  trivial: fix typos in comments s/DGBU/DBGU/
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: Remove duplicate Kconfig entry
  HID: consolidate connect and disconnect into core code
  HID: fix non-atomic allocation in hid_input_report

Add a driver for the the Consumer IR (CIR) functionality of the Winbond
WPCD376I chipset (found on e.g. Intel DG45FC motherboards).
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The shutdown method is used by the winbond cir driver to setup the
hardware for wake-from-S5.
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NDavid Härdeman <david@hardeman.nu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On resume from suspend, the driver currently resets the logical state as
if it was brought up from halt.  This patch uses the
dev_pm_ops.resume/restore methods to synchronize the hardware with the
memorized logical state, in effect bringing back the accelerometer and
backlight to the state prior to suspend.  Works for both suspend to ram
and hibernation.  The patch has zero effect on the running state.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If already requested, gpio_data and irq should be freed in the case of an
error.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NJonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Occasionally it is helpful to be able to turn a temperature sensor off
(for example if it's making unwanted electrical noise).  This patch
adds a sysfs node to put any adm1021 compatible device into low power mode.
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ADM1023 temperature sensor supports higher resolution for its external
sensor (sensitivity of 1/8 deg C).  This patch makes this higher
resolution available through the appropriate temperature sysfs nodes.

Curiously, this functionality was available in the 2.4 kernel driver (but
formatted in a less helpful manner).

Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: NMichael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This enabled power management functions for the SPI transport layer of the
lis3 devices.  The device's suspend mode is only entered in case no wakeup
threshold has been given.  In this case, the device is supposed to wake up
the system and must thus not be put to deep sleep.

[randy.dunlap@oracle.com: fix lis3-spi for CONFIG_PM=n]
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This offers a way for platforms to define flags and thresholds for the
free-fall/wakeup functions of the lis302d chips.

More registers needed to be seperated as they are specific to the
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Bit 0x80 in CTRL_REG3 is an ACTIVE_LOW rather than an ACTIVE_HIGH
function, I got that wrong during my last change.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NPavel Machek <pavel@ucw.cz>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable the coretemp driver on an Intel Atom.

I'm not sure if the readings are correct, however - on my 330, the driver
reports values between 27 and 41 °C (with core1 being about 8°C hotter
than core0, given the same load).  Maybe the maximum temperature of 100 °C
is wrong for Atom CPUs.

Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add checks for Blackfin-specific issues that seem to crop up from time to
time.  In particular, we have helper macros to break a 32bit address into
the hi/lo parts, and we want to make sure people use the csync/ssync
variant that includes fun anomaly workarounds.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Limit our type matcher to the s/u/le/be etc sizes that actually exist to
prevent miss categorising s2 as a type.  Fix up the spelling of the error
also.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We should not recommend braces for the following:

    #define pr_fmt(fmt)    "%s: " fmt, __func__

allow things with double quotes round them to avoid this check.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Impact:
  - More verbose help/usage message.
  - Make the option -f an alias for --file.
  - On -h, --help, and --version display help message and exit(0).
  - With no FILE(s) given, exit(1) with "no input files".
  - On invalid options display help/usage and exit(1).

Based on a patch by Pavel Machek.
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Acked-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Ensure we terminate when there are no futher continuation lines when
trying to determine relative indent of conditionals and their blocks.
Reported-by: NJohn Daiker <daikerjohn@gmail.com>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes the sanitation process in checkpatch.pl so that it blocks out
the text after a C99 style comment the same way it does with block style
comments.  This prevents the text from getting processed as regular code.
Signed-off-by: NDaniel Walker <dwalker@fifo99.com>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

An else cannot start a type, it would have to be within a block after the
else.  This can trigger false modifier matching.
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add kerneldoc annotations for function formals of type struct flex_array
and gfp_t which are currently lacking.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

FLEX_ARRAY_INIT(element_size, total_nr_elements) cannot determine if
either parameter is valid, so flex arrays which are statically allocated
with this interface can easily become corrupted or reference beyond its
allocated memory.

This removes FLEX_ARRAY_INIT() as a struct flex_array initializer since no
initializer may perform the required checking.  Instead, the array is now
defined with a new interface:

	DEFINE_FLEX_ARRAY(name, element_size, total_nr_elements)

This may be prefixed with `static' for file scope.

This interface includes compile-time checking of the parameters to ensure
they are valid.  Since the validity of both element_size and
total_nr_elements depend on FLEX_ARRAY_BASE_SIZE and FLEX_ARRAY_PART_SIZE,
the kernel build will fail if either of these predefined values changes
such that the array parameters are no longer valid.

Since BUILD_BUG_ON() requires compile time constants, several of the
static inline functions that were once local to lib/flex_array.c had to be
moved to include/linux/flex_array.h.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Acked-by: NDave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a new function to the flex_array API:

	int flex_array_shrink(struct flex_array *fa)

This function will free all unused second-level pages.  Since elements are
now poisoned if they are not allocated with __GFP_ZERO, it's possible to
identify parts that consist solely of unused elements.

flex_array_shrink() returns the number of pages freed.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>