Base versions handle constant folding now.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent fix of data corruption when splicing from sockets uses
memory very inefficiently allocating a new page to copy each chunk of
linear part of skb. This patch uses the same page until it's full
(almost) by caching the page in sk_sndmsg_page field.

With changes from David S. Miller <davem@davemloft.net>
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some platforms (for example pcm037) do not have an EEPROM fitted,
instead storing their mac address somewhere else.  The bootloader
fetches this and configures the ethernet adapter before the kernel is
started.

This patch allows a platform to indicate to the driver via the
SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been
configured via such a mechanism, and should be saved before resetting
the chip.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported.  These
are usually indicated by a hardware strap which sets an "external PHY
detected" bit in the HW_CFG register.

In some cases it is desirable to override this hardware strap and force
use of either the internal phy or an external PHY.  This patch adds
SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a
platform can indicate this preference via its platform_data.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Tested-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The isr supports shared operation, so register it with the IRQF_SHARED
flag to indicate this.

This patch also removes the IRQF_DISABLED flag.  This driver doesn't
need it, and IRQF_DISABLED isn't guaranteed when using shared interrupts.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch adds support for the platform_device's resources to indicate
additional flags to use when registering the irq, for example
IORESOURCE_IRQ_LOWLEVEL (which corresponds to IRQF_TRIGGER_LOW).  These
should be set in the irq resource flags field.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/e1000/e1000_main.c

As the mmap handler gets called under mmap_sem, and we may grab
mmap_sem elsewhere under the socket lock to access user data, we
should avoid grabbing the socket lock in the mmap handler.

Since the only thing we care about in the mmap handler is for
pg_vec* to be invariant, i.e., to exclude packet_set_ring, we
can achieve this by simply using a new mutex.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Tested-by: NMartin MOKREJŠ <mmokrejs@ribosome.natur.cuni.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we use a spin-lock to serialise statistics fetches and also
to inhibit them for short periods of time, plus a flag to
enable/disable statistics fetches for longer periods of time, during
online reset.  This was apparently insufficient to deal with the several
reasons for stats being disabled.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All 10Xpress PHYs require autonegotiation all the time; enforce this
in the set_settings() method and do not treat it as a workaround.

Remove claimed support for 100M HD mode since it is not supported by
current firmware.

Do not set speed override bits when AN is enabled, and do not use
register 1.49192 for AN configuration as it can override what we set
elsewhere.

Always set the AN selector bits to 1 (802.3).

Fix confusion between Next Page and Extended Next Page.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This workaround is not specific to rev A.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on the loopback mode, there may be no pertinent link state
bits.  In this case we test the PHYXS RX fault bit instead.  Make
sure to do this in all cases where there are no link state bits.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In particular, set pause advertising bits properly.

A PHY reset is not necessary to recover from the register self-test,
so use a "invisible" reset there instead.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Modify falcon_switch_mac() to always set NIC_STAT_REG, even if the the
MAC is the same as it was before.  This ensures that the value is
correct after an online reset.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change sfn4111t_reset() to change only GPIO output enables so that it
doesn't break subsequent I2C operations.

Update comments to explain exactly what we're doing.

Add a short sleep to make sure the FLASH_CFG_1 value is latched before
any subsequent I2C operations.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of disabling AN in loopback, just prevent restarting AN and
override the speed in sft9001_get_settings().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Early versions of the SFX7101 firmware could complete link training in
a state where it would not adequately cancel noise (Solarflare bug
10750).  We previously worked around this by resetting the PHY after
seeing many Ethernet CRC errors.  This workaround is unsafe since it
takes no account of the interval between errors; it also appears to
be unnecessary with production firmware.  Therefore remove it.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable a firmware option that appears to be necessary for reliable
operation.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Printing anything over netconsole before hw is up and running is,
of course, not going to work.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with current kernels, tulip 21142 ethernet controllers fail to connect
to a 10Mbps only (i.e. without negotiation-partner) network.  It used
to work in 2.4 kernels.  Fix that.  Tested on a 21142 Rev 0x11.
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix inverted logic
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 0f0ca340 ("phy: power
management support") caused a regression in the gianfar driver.

Now phylib turns off PHY power during suspend, and thus WOL
doesn't work anymore.

This patch workarounds the issue by enabling wakeup in the MDIO
device, i.e. just restores the old behaviour for the gianfar
driver. Note that this way all PHYs on a given MDIO bus won't
be turned off during suspend, which isn't good from the power
saving point of view.

A proper, per netdevice wakeup management support will need
a bit reworked phylib suspend/resume logic.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With a postfix decrement the timeout will reach -1 rather than 0,
so the warning will not be issued.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Acked-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smsc9420 performs an interrupt signalling test when the interface is
brought up.  The current code mistakenly sets its test flag to false
AFTER enabling the software interrupt source, making failure quite
likely.

This patch changes the code to set the test flag BEFORE enabling
interrupts. I've also removed an smp_wmb because the following spinlock
provides an implicit memory barrier.
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit b31a1d8b ("gianfar: Convert
gianfar to an of_platform_driver") changes the gianfar's phy id to the
format like "mdio@xxxx:xx", but uec still uses the old format like
"xxxxxxxx:xx".  For the board whose UEC uses gianfar-mdio like
MPC8568MDS, the phy can not be attached because of the incompatible
phy id format. This patch changes uec's phy id to the same format as
gianfar's.
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As reported by Toralf Förster and Randy Dunlap.

- http://linuxwimax.org/pipermail/wimax/2009-January/000460.html

- http://lkml.org/lkml/2009/1/29/279

The definitions needed for the wimax stack and i2400m driver debug
infrastructure was, by mistake, compiled depending on CONFIG_DEBUG_FS
(by them being placed in the debugfs.c files); thus the build broke in
2.6.29-rc3 when debugging was enabled (CONFIG_WIMAX_DEBUG) and
DEBUG_FS was disabled.

These definitions are always needed if debug is enabled at compile
time (independently of DEBUG_FS being or not enabled), so moving them
to a file that is always compiled fixes the issue.
Signed-off-by: NInaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For kernel bugzilla #12537:
http://bugzilla.kernel.org/show_bug.cgi?id=12537

Free memory.
Signed-off-by: NDaniel Marjamäki <danielm77@spray.se>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a report from Michael Tokarev <mjt@tls.msk.ru>:

	Just saw in dmesg:

	ioctl32(kvm:4408): Unknown cmd fd(9) cmd(800454cf){t:'T';sz:4} arg(ffc668e4) on /dev/net/tun
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch optimises napi_fraginfo_skb to only copy the bits
necessary.  We also open-code the memcpy so that the alignment
information is always available to gcc.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gro: Do not merge paged packets into frag_list

Bigger is not always better :)

It was easy to continue to merged packets into frag_list after the
page array is full.  However, this turns out to be worse than LRO
because frag_list is a much less efficient form of storage than the
page array.  So we're better off stopping the merge and starting
a new entry with an empty page array.

In future we can optimise this further by doing frag_list merging
but making sure that we continue to fill in the page array.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unfortunately simplicity isn't always the best.  The fraginfo
interface turned out to be suboptimal.  The problem was quite
obvious.  For every packet, we have to copy the headers from
the frags structure into skb->head, even though for 99% of the
packets this part is immediately thrown away after the merge.

LRO didn't have this problem because it directly read the headers
from the frags structure.

This patch attempts to address this by creating an interface
that allows GRO to access the headers in the first frag without
having to copy it.  Because all drivers that use frags place the
headers in the first frag this optimisation should be enough.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently VLAN still has a bit of common code handling the aftermath
of GRO that's shared with the common path.  This patch moves them
into shared helpers to reduce code duplication.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBenjamin Zores <benjamin.zores@alcatel-lucent.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This documentation is old.  Add a short note to describe why aliases
are no long necessary, and remove the old contact/edit info.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It oopsd for me in skb_seq_read. addr2line said it was
linux-2.6/net/core/skbuff.c:2228, which is this line:


	while (st->frag_idx < skb_shinfo(st->cur_skb)->nr_frags) {


I added some printks in there and it looks like we hit this:

        } else if (st->root_skb == st->cur_skb &&
                   skb_shinfo(st->root_skb)->frag_list) {
                 st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
                 st->frag_idx = 0;
                 goto next_skb;
        }



Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.

 	if (abs_offset < block_limit) {
-		*data = st->cur_skb->data + abs_offset;
+		*data = st->cur_skb->data + (abs_offset - st->stepped_offset);

I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -

It hit this if condition -

        if (st->cur_skb->next) {
                st->cur_skb = st->cur_skb->next;
                st->frag_idx = 0;
                goto next_skb;

And so, now the st pointer is shifted to the next skb whereas actually
it should have hit the second else if first since the data is in the
frag_list.

        else if (st->root_skb == st->cur_skb &&
                 skb_shinfo(st->root_skb)->frag_list) {
                st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
                goto next_skb;
        }

Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches. 
Signed-off-by: NShyam Iyer <shyam_iyer@dell.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The frag_list handling was broken in skb_seq_read:

1) We didn't add the stepped offset when looking at the head
are of fragments other than the first.

2) We didn't take the stepped offset away when setting the data
pointer in the head area.

3) The frag index wasn't reset.

This patch fixes both issues.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.

This was reduced in commit 32ec8033
("netxen: reduce memory footprint").

Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ath5k_config updates the software context without taking sc->lock.

Changes-licensed-under: 3-Clause-BSD
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>