This patch changes content of hashlist (used to get port struct by
computed index (0...en_port_count-1)). Now the hash list contains only
enabled ports so userspace will be able to say what ports can be used
for tx/rx. This becomes handy when userspace will need to disable ports
which does not belong to active aggregator. By default, newly added port
is enabled.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are options, which are set up on a socket while performing
TCP handshake. Need to resurrect them on a socket while repairing.
A new sockoption accepts a buffer and parses it. The buffer should
be CODE:VALUE sequence of bytes, where CODE is standard option
code and VALUE is the respective value.

Only 4 options should be handled on repaired socket.

To read 3 out of 4 of these options the TCP_INFO sockoption can be
used. An ability to get the last one (the mss_clamp) was added by
the previous patch.

Now the restore. Three of these options -- timestamp_ok, mss_clamp
and snd_wscale -- are just restored on a coket.

The sack_ok flags has 2 issues. First, whether or not to do sacks
at all. This flag is just read and set back. No other sack  info is
saved or restored, since according to the standart and the code
dropping all sack-ed segments is OK, the sender will resubmit them
again, so after the repair we will probably experience a pause in
connection. Next, the fack bit. It's just set back on a socket if
the respective sysctl is set. No collected stats about packets flow
is preserved. As far as I see (plz, correct me if I'm wrong) the
fack-based congestion algorithm survives dropping all of the stats
and repairs itself eventually, probably losing the performance for
that period.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This includes (according the the previous description):

* TCP_REPAIR sockoption

This one just puts the socket in/out of the repair mode.
Allowed for CAP_NET_ADMIN and for closed/establised sockets only.
When repair mode is turned off and the socket happens to be in
the established state the window probe is sent to the peer to
'unlock' the connection.

* TCP_REPAIR_QUEUE sockoption

This one sets the queue which we're about to repair. The
'no-queue' is set by default.

* TCP_QUEUE_SEQ socoption

Sets the write_seq/rcv_nxt of a selected repaired queue.
Allowed for TCP_CLOSE-d sockets only. When the socket changes
its state the other seq-s are changed by the kernel according
to the protocol rules (most of the existing code is actually
reused).

* Ability to forcibly bind a socket to a port

The sk->sk_reuse is set to SK_FORCE_REUSE.

* Immediate connect modification

The connect syscall initializes the connection, then directly jumps
to the code which finalizes it.

* Silent close modification

The close just aborts the connection (similar to SO_LINGER with 0
time) but without sending any FIN/RST-s to peer.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is just the preparation patch, which makes the needed for
TCP repair code ready for use.
Signed-off-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All of the users have been converted to use registera_net_sysctl so we
no longer need register_net_sysctl.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't use struct ctl_path anymore so delete the exported constants.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There isn't much advantage here except that strings paths are a bit
easier to read, and converting everything to them allows me to kill off
ctl_path.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sysctl core no longer natively understands sysctl tables
with .child entries.

Split the ipv6_table to remove the .child entries.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't register/unregister every ax25 table in a batch.  Instead register
and unregister per device ax25 sysctls as ax25 devices come and go.

This moves ax25 to be a completely modern sysctl user.  Registering the
sysctls in just the initial network namespace, removing the use of
.child entries that are no longer natively supported by the sysctl core
and taking advantage of the fact that there are no longer any ordering
constraints between registering and unregistering different sysctl
tables.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sysctl no longer requires explicit creation of directories.  The neigh
directory is always populated with at least a default entry so this
won't cause any user visible changes.

Delete the ipv4_path and the ipv4_skeleton these are no longer needed.

Directly register the ipv4_route_table.

And since I am an idiot remove the header definitions that I should
have removed in the previous patch.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

register_sysctl_rotable never caught on as an interesting way to
register sysctls.  My take on the situation is that what we want are
sysctls that we can only see in the initial network namespace.  What we
have implemented with register_sysctl_rotable are sysctls that we can
see in all of the network namespaces and can only change in the initial
network namespace.

That is a very silly way to go.  Just register the network sysctls
in the initial network namespace and we don't have any weird special
cases to deal with.

The sysctls affected are:
/proc/sys/net/ipv4/ipfrag_secret_interval
/proc/sys/net/ipv4/ipfrag_max_dist
/proc/sys/net/ipv6/ip6frag_secret_interval
/proc/sys/net/ipv6/mld_max_msf

I really don't expect anyone will miss them if they can't read them in a
child user namespace.

CC: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the netfilter code is modified to use register_net_sysctl_table the
kernel fails to boot because the per net sysctl infrasturce is not setup
soon enough.  So to avoid races call net_sysctl_init from sock_init().
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Right now all of the networking sysctl registrations are running in a
compatibiity mode.  The natvie sysctl registration api takes a cstring
for a path and a simple ctl_table.  Implement register_net_sysctl so
that we can register network sysctls without needing to use
compatiblity code in the sysctl core.

Switching from a ctl_path to a cstring results in less boiler plate
and denser code that is a little easier to read.

I would simply have changed the arguments to register_net_sysctl_table
instead of keeping two functions in parallel but gcc will allow a
ctl_path pointer to be passed to a char * pointer with only issuing a
warning resulting in completely incorrect code can be built.  Since I
have to change the function name I am taking advantage of the situation
to let both register_net_sysctl and register_net_sysctl_table live for a
short time in parallel which makes clean conversion patches a bit easier
to read and write.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Acked-by: NPavel Emelyanov <xemul@parallels.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Put use & mask on same location to avoid two holes on 64bit arches
Signed-off-by: NEric Dumazet <edumazet@google.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add utility function to provide the average rssi per vif
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit b82d1bb4 inadvertendly placed unrelated new code between
TCPCB_EVER_RETRANS and TCPCB_RETRANS and the other macros that refer
to the sacked field in the struct tcp_skb_cb (probably because there
was a misleading empty line there). This commit fixes up the
formatting so that all macros related to the sacked field are adjacent
again.
Signed-off-by: NNeal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per sections 8.4.2.100.2 and 8.4.2.100.3 of Std 802.11-2012
Reported-by: NShinichi Hotori <hotorinn@gmail.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My grand plan to allow drivers to gradually move over
to advertising virtual interface combinations and only
enforce with drivers that do want it enforced doesn't
seem to be working out, only Christian ever added the
advertising (to carl9170), nobody else did.

Begin enforcing combinations in cfg80211 so that users
can rely on the information reported about a device.

Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Bob Copeland <me@bobcopeland.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds FDB bridge ops to the macvlan device passthru mode.
Additionally a flags field was added and a NOPROMISC bit to
allow users to use passthru mode without the driver calling
dev_set_promiscuity(). The flags field is a u16 placed in a
4 byte hole (consuming 2 bytes) of the macvlan_dev struct.

We want to do this so that the macvlan driver or stack
above the macvlan driver does not have to process every
packet. For the use case where we know all the MAC addresses
of the endstations above us this works well.

This patch is a result of Roopa Prabhu's work. Follow up
patches are needed for VEPA and VEB macvlan modes.

v2: Change from distinct nopromisc mode to a flags field to
    configure this. This avoids the tendency to add a new
    mode every time we need some slightly different behavior.
v3: fix error in dev_set_promiscuity and add change and get
    link attributes for flags.

CC: Roopa Prabhu <roprabhu@cisco.com>
CC: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a dev_uc_add_excl() and dev_mc_add_excl() calls
similar to the original dev_{uc|mc}_add() except it sets
the global bit and returns -EEXIST for duplicat entires.

This is useful for drivers that support SR-IOV, macvlan
devices and any other devices that need to manage the
unicast and multicast lists.

v2: fix typo UNICAST should be MULTICAST in dev_mc_add_excl()

CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds two new flags NTF_MASTER and NTF_SELF that can
now be used to specify where PF_BRIDGE netlink commands should
be sent. NTF_MASTER sends the commands to the 'dev->master'
device for parsing. Typically this will be the linux net/bridge,
or open-vswitch devices. Also without any flags set the command
will be handled by the master device as well so that current user
space tools continue to work as expected.

The NTF_SELF flag will push the PF_BRIDGE commands to the
device. In the basic example below the commands are then parsed
and programmed in the embedded bridge.

Note if both NTF_SELF and NTF_MASTER bits are set then the
command will be sent to both 'dev->master' and 'dev' this allows
user space to easily keep the embedded bridge and software bridge
in sync.

There is a slight complication in the case with both flags set
when an error occurs. To resolve this the rtnl handler clears
the NTF_ flag in the netlink ack to indicate which sets completed
successfully. The add/del handlers will abort as soon as any
error occurs.

To support this new net device ops were added to call into
the device and the existing bridging code was refactored
to use these. There should be no required changes in user space
to support the current bridge behavior.

A basic setup with a SR-IOV enabled NIC looks like this,

          veth0  veth2
            |      |
          ------------
          |  bridge0 |   <---- software bridging
          ------------
               /
               /
  ethx.y      ethx
    VF         PF
     \         \          <---- propagate FDB entries to HW
     \         \
  --------------------
  |  Embedded Bridge |    <---- hardware offloaded switching
  --------------------

In this case the embedded bridge must be managed to allow 'veth0'
to communicate with 'ethx.y' correctly. At present drivers managing
the embedded bridge either send frames onto the network which
then get dropped by the switch OR the embedded bridge will flood
these frames. With this patch we have a mechanism to manage the
embedded bridge correctly from user space. This example is specific
to SR-IOV but replacing the VF with another PF or dropping this
into the DSA framework generates similar management issues.

Examples session using the 'br'[1] tool to add, dump and then
delete a mac address with a new "embedded" option and enabled
ixgbe driver:

# br fdb add 22:35:19:ac:60:59 dev eth3
# br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
#br fdb add 22:35:19:ac:60:59 embedded dev eth3
#br fdb
port    mac addr                flags
veth0   22:35:19:ac:60:58       static
veth0   9a:5f:81:f7:f6:ec       local
eth3    00:1b:21:55:23:59       local
eth3    22:35:19:ac:60:59       static
veth0   22:35:19:ac:60:57       static
eth3    22:35:19:ac:60:59       local embedded
#br fdb del 22:35:19:ac:60:59 embedded dev eth3

I added a couple lines to 'br' to set the flags correctly is all. It
is my opinion that the merit of this patch is now embedded and SW
bridges can both be modeled correctly in user space using very nearly
the same message passing.

[1] 'br' tool was published as an RFC here and will be renamed 'bridge'
    http://patchwork.ozlabs.org/patch/117664/

Thanks to Jamal Hadi Salim, Stephen Hemminger and Ben Hutchings for
valuable feedback, suggestions, and review.

v2: fixed api descriptions and error case with both NTF_SELF and
    NTF_MASTER set plus updated patch description.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use of "unsigned int" is preferred to bare "unsigned" in net tree.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As hypervior does not have the knowledge of guest network configuration, it's
better to ask guest to send gratuitous packets when needed.

This patch implements VIRTIO_NET_F_GUEST_ANNOUNCE feature: hypervisor would
notice the guest when it thinks it's time for guest to announce the link
presnece. Guest tests VIRTIO_NET_S_ANNOUNCE bit during config change interrupt
and woule send gratuitous packets through netif_notify_peers() and ack the
notification through ctrl vq.

We need to make sure the atomicy of read and ack in guest otherwise we may ack
more times than being notified. This is done through handling the whole config
change interrupt in an non-reentrant workqueue.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We must try harder to get unique (addr, port) pairs when
doing port autoselection for sockets with SO_REUSEADDR
option set.

We achieve this by adding a relaxation parameter to
inet_csk_bind_conflict. When 'relax' parameter is off
we return a conflict whenever the current searched
pair (addr, port) is not unique.

This tries to address the problems reported in patch:
	8d238b25
	Revert "tcp: bind() fix when many ports are bound"

Tests where ran for creating and binding(0) many sockets
on 100 IPs. The results are, on average:

	* 60000 sockets, 600 ports / IP:
		* 0.210 s, 620 (IP, port) duplicates without patch
		* 0.219 s, no duplicates with patch
	* 100000 sockets, 1000 ports / IP:
		* 0.371 s, 1720 duplicates without patch
		* 0.373 s, no duplicates with patch
	* 200000 sockets, 2000 ports / IP:
		* 0.766 s, 6900 duplicates without patch
		* 0.768 s, no duplicates with patch
	* 500000 sockets, 5000 ports / IP:
		* 2.227 s, 41500 duplicates without patch
		* 2.284 s, no duplicates with patch
Signed-off-by: NAlex Copot <alex.mihai.c@gmail.com>
Signed-off-by: NDaniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two struct request_sock_ops providers, tcp and dccp.

inet_csk_reqsk_queue_prune() can avoid testing syn_ack_timeout being
NULL if we make it non NULL like syn_ack_timeout
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Cc: dccp@vger.kernel.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Updates some comments to track RFC6298
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the per-cpu statistics kept for GRE, IPIP, and SIT tunnels
to use 64 bit statistics.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removes hw.conf.channel usage from the following functions:
 * ieee80211_mandatory_rates
 * ieee80211_sta_get_rates
 * ieee80211_frame_duration
 * ieee80211_rts_duration
 * ieee80211_ctstoself_duration

This is in preparation for multi-channel operation.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If the current channel is known, add frequency and channel type to
NL80211_CMD_GET_INTERFACE.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

net/core/rtnetlink.c: In function ‘rtnl_create_link’:
net/core/rtnetlink.c:1645:3: warning: passing argument 2 of ‘ops->get_tx_queues’ from incompatible pointer type [enabled by default]
net/core/rtnetlink.c:1645:3: note: expected ‘const struct nlattr **’ but argument is of type ‘struct nlattr **’
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

neigh_table_init_no_netlink() is only used in net/core/neighbour.c file.
Signed-off-by: NHiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most machines dont use UDP encapsulation (L2TP)

Adds a static_key so that udp_queue_rcv_skb() doesnt have to perform a
test if L2TP never setup the encap_rcv on a socket.

Idea of this patch came after Simon Horman proposal to add a hook on TCP
as well.

If static_key is not yet enabled, the fast path does a single JMP .

When static_key is enabled, JMP destination is patched to reach the real
encap_type/encap_rcv logic, possibly adding cache misses.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: dev@openvswitch.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix spelling and references in rtnetlink.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change get_tx_queues, drop unsused arg/return value real_tx_queues,
and use return by value (with error) rather than call by reference.

Probably bonding should just change to LLTX and the whole get_tx_queues
API could disappear!
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb struct ubuf_info callback gets passed struct ubuf_info
itself, not the arg value as the field name and the function signature
seem to imply. Rename the arg field to ctx to match usage,
add documentation and change the callback argument type
to make usage clear and to have compiler check correctness.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the ipv6 dst cache which copy from the dst generated by ICMPV6 RA packet.
this dst cache will not check expire because it has no RTF_EXPIRES flag.
So this dst cache will always be used until the dst gc run.

Change the struct dst_entry,add a union contains new pointer from and expires.
When rt6_info.rt6i_flags has no RTF_EXPIRES flag,the dst.expires has no use.
we can use this field to point to where the dst cache copy from.
The dst.from is only used in IPV6.

rt6_check_expired check if rt6_info.dst.from is expired.

ip6_rt_copy only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.

ip6_dst_destroy release the ort.

Add some functions to operate the RTF_EXPIRES flag and expires(from) together.
and change the code to use these new adding functions.

Changes from v5:
modify ip6_route_add and ndisc_router_discovery to use new adding functions.

Only set dst.from when the ort has flag RTF_ADDRCONF
and RTF_DEFAULT.then hold the ort.
Signed-off-by: NGao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement aggregation algorithm, combining more data into a single
HSI transfer. 4 different traffic categories are supported:
 1. TC_PRIO_CONTROL .. TC_PRIO_MAX (CTL)
 2. TC_PRIO_INTERACTIVE            (VO)
 3. TC_PRIO_INTERACTIVE_BULK       (VI)
 4. TC_PRIO_BESTEFFORT, TC_PRIO_BULK, TC_PRIO_FILLER (BEBK)
Signed-off-by: NDmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set traffic class for CAIF packets, based on socket
priority, CAIF protocol type, or type of message.

Traffic class mapping for different packet types:
 - control:       TC_PRIO_CONTROL;
 - flow control:  TC_PRIO_CONTROL;
 - at:            TC_PRIO_CONTROL;
 - rfm:           TC_PRIO_INTERACTIVE_BULK;
 - other sockets: equals to socket's TC;
 - network data:  no change.
Signed-off-by: NDmitry Tarnyagin <dmitry.tarnyagin@stericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>