Fix a problem in which iSCSI-boot installation fails when switching SFP+ boot
port and moving the SFP+ module prior to boot. The SFP+ insertion triggers an
interrupt which configures the SFP+ module wrongly before interface is loaded.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a KR2 device is connected to a KR link-partner, sometimes it requires
disabling KR2 for the link to come up. To get a KR2 link up later, in case no
base pages are seen, the KR2 is restored. The problem was that some link
partners cleared their advertised BP/NP after around two seconds, causing the
driver to disable/enable KR2 link all the time.
The fix was to wait at least 5 seconds before checking KR2 recovery.
Signed-off-by: NYaniv Rosner <yanivr@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macvlan already supports hw address filters.  Set the IFF_UNICAST_FLT
so that it doesn't needlesly enter PROMISC mode when macvlans are
stacked.
Signed-of-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a team port is removed, unsync all devices addresses that may have
been synched to the port devices.

CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Obviously, vid should be considered when searching for multicast
group.

Cc: Vlad Yasevich <vyasevic@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <amwang@redhat.com>
Acked-by: NVlad Yasevich <vyasevich@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In e337e24d (inet: Fix kmemleak in tcp_v4/6_syn_recv_sock and
dccp_v4/6_request_recv_sock) I introduced the function
inet_csk_prepare_forced_close, which does a call to bh_unlock_sock().
This produces a sparse-warning.

This patch adds the missing __releases.
Signed-off-by: NChristoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMartin Zhang <martinbj2008@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we have a large number of static label mappings that spill across
the netlink message boundary we fail to properly save our state in the
netlink_callback struct which causes us to repeat the same listings.
This patch fixes this problem by saving the state correctly between
calls to the NetLabel static label netlink "dumpit" routines.
Signed-off-by: NPaul Moore <pmoore@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When autoneg has been disabled in the PHY (Marvell 88E1118 here), auto
negotiation between MAC and PHY seem non-functional anymore. The only
way I found to workaround this is to manually configure the MAC with the
settings sent to the PHY earlier.
Signed-off-by: NPhil Sutter <phil.sutter@viprinet.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if we set up netconsole over bonding and release a slave,
netconsole will stop logging on the whole bonding device. Change the
behavior to stop the netconsole only when the last slave is released.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following script will produce a kernel oops:

    sudo ip netns add v
    sudo ip netns exec v ip ad add 127.0.0.1/8 dev lo
    sudo ip netns exec v ip link set lo up
    sudo ip netns exec v ip ro add 224.0.0.0/4 dev lo
    sudo ip netns exec v ip li add vxlan0 type vxlan id 42 group 239.1.1.1 dev lo
    sudo ip netns exec v ip link set vxlan0 up
    sudo ip netns del v

where inspect by gdb:

    Program received signal SIGSEGV, Segmentation fault.
    [Switching to Thread 107]
    0xffffffffa0289e33 in ?? ()
    (gdb) bt
    #0  vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
    #1  vxlan_stop (dev=0xffff88001bafa000) at drivers/net/vxlan.c:1087
    #2  0xffffffff812cc498 in __dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1299
    #3  0xffffffff812cd920 in dev_close_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:1335
    #4  0xffffffff812cef31 in rollback_registered_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:4851
    #5  0xffffffff812cf040 in unregister_netdevice_many (head=head@entry=0xffff88001f2e7dc8) at net/core/dev.c:5752
    #6  0xffffffff812cf1ba in default_device_exit_batch (net_list=0xffff88001f2e7e18) at net/core/dev.c:6170
    #7  0xffffffff812cab27 in cleanup_net (work=<optimized out>) at net/core/net_namespace.c:302
    #8  0xffffffff810540ef in process_one_work (worker=0xffff88001ba9ed40, work=0xffffffff8167d020) at kernel/workqueue.c:2157
    #9  0xffffffff810549d0 in worker_thread (__worker=__worker@entry=0xffff88001ba9ed40) at kernel/workqueue.c:2276
    #10 0xffffffff8105870c in kthread (_create=0xffff88001f2e5d68) at kernel/kthread.c:168
    #11 <signal handler called>
    #12 0x0000000000000000 in ?? ()
    #13 0x0000000000000000 in ?? ()
    (gdb) fr 0
    #0  vxlan_leave_group (dev=0xffff88001bafa000) at drivers/net/vxlan.c:533
    533		struct sock *sk = vn->sock->sk;
    (gdb) l
    528	static int vxlan_leave_group(struct net_device *dev)
    529	{
    530		struct vxlan_dev *vxlan = netdev_priv(dev);
    531		struct vxlan_net *vn = net_generic(dev_net(dev), vxlan_net_id);
    532		int err = 0;
    533		struct sock *sk = vn->sock->sk;
    534		struct ip_mreqn mreq = {
    535			.imr_multiaddr.s_addr	= vxlan->gaddr,
    536			.imr_ifindex		= vxlan->link,
    537		};
    (gdb) p vn->sock
    $4 = (struct socket *) 0x0

The kernel calls `vxlan_exit_net` when deleting the netns before shutting down
vxlan interfaces. Later the removal of all vxlan interfaces, where `vn->sock`
is already gone causes the oops. so we should manually shutdown all interfaces
before deleting `vn->sock` as the patch does.
Signed-off-by: NZang MingJie <zealot0630@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Linux is free to call ethtool ops as soon as a netdev exists when probe
finishes. However, we only allocate vmxnet3 tx/rx queues and initialize the
rx_buf_per_pkt field in struct vmxnet3_adapter when the interface is
opened (UP).
Signed-off-by: NBhavesh Davda <bhavesh@vmware.com>
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Here's a batch of fixes to the mlx4 core and ethernet drivers for 3.9

The commit that disabled RFS when running in SRIOV mode fixes a regression which was
introduced in 3.9-rc1 but actually present also in the 3.8 -stable series. It turns out
that a slightly different fix is needed there and we will generate and submit it there.

Patches done against net commit 66d29cbc "benet: Wait f/w POST until timeout"
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 37706996 "mlx4_en: fix allocation of CPU affinity reverse-map" fixed
a bug when mlx4_dev->caps.comp_pool is larger from the device rx rings, but
introduced a regression.

When the mlx4_core is activating its "legacy mode" (e.g when running in SRIOV
mode) w.r.t to EQs/IRQs usage, comp_pool becomes zero and we're crashing on
divide by zero alloc_cpu_rmap.

Fix that by enabling RFS only when running in non-legacy mode.
Reported-by: NYan Burman <yanb@mellanox.com>
Cc: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure we cleanup all MAC related resources (entries in the port MAC
table and steering rules) when stopping a port or when the driver is unloaded.

The leak was introduced by commit 07cb4b0a "net/mlx4_en: Manage hash of MAC
addresses per port".
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary use of workqueue for the device MAC address setting
flow, and fix a race when setting MAC address which was introduced by
commit c07cb4b0 "net/mlx4_en: Manage hash of MAC addresses per port"

The race happened when mlx4_en_replace_mac was being executed in parallel
with a successive call to ndo_set_mac_address, e.g witn an A/B/A MAC
setting configuration test, the third set fails.

With this change we also properly report an error if set MAC fails.
Signed-off-by: NYan Burman <yanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The set_param_l function assumes casting a u64 pointer to a u32 pointer
allows to access the lower 32bits, but it results in writing the upper
32 bits on big endian systems.

The fixed function reads the upper 32 bits of the 64 argument, and or's
them with the 32 bits of the 32-bit value passed to the function.

Since this is now a "read-modify-write" operation, we got many
"unintialized variable" warnings which needed to be fixed as well.

Reported-by: Alexander Schmidt <alexschm@de.ibm.com>.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Older kernels detect DMFS (device-managed flow steering) from the HCA
device capability directly, regardless of whether the capability was
enabled in INIT_HCA, this is fixed by commit 7b8157be "mlx4_core: Adjustments
to Flow Steering activation logic for SR-IOV"

To protect against guests running kernels without this fix, the host driver
should turn off the DMFS capability bit in mlx4_QUERY_DEV_CAP_wrapper.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Guests kernels may not correctly detect if DMFS (device-enabled flow steering) is
activated by the host. If DMFS is activated, the master should return error to guests
which try to use the B0-steering flow calls (mlx4_QP_ATTACH).
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
The following patchset contains Netfilter fixes for your net tree,
they are:

* Don't generate audit log message if audit is not enabled, from Gao Feng.

* Fix logging formatting for packets dropped by helpers, by Joe Perches.

* Fix a compilation warning in nfnetlink if CONFIG_PROVE_RCU is not set,
  from Paul Bolle.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
This series contains updates to e1000e only.

All three patches come from Konstantin Khlebnikov to resolve power
management issues.  The first patch removes redundant and unbalanced
pci_disable_device() from the shutdown function.  The second patch
removes redundant actions from the driver and fixes the interaction
with actions in pci-bus runtime power management code.  The third
and last patch fixes some messages like 'Error reading PHY register'
and 'Hardware Erorr' and saves several seconds on reboot.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some annoying messages like 'Error reading PHY register' and
'Hardware Erorr' and saves several seconds on reboot.

Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NBorislav Petkov <bp@suse.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes redundant actions from driver and fixes its interaction
with actions in pci-bus runtime power management code.

It removes pci_save_state() from __e1000_shutdown() for normal adapters,
PCI bus callbacks pci_pm_*() will do all this for us. Now __e1000_shutdown()
switches to D3-state only quad-port adapters, because they needs quirk for
clearing false-positive error from downsteam pci-e port.

pci_save_state() now called after clearing bus-master bit, thus __e1000_resume()
and e1000_io_slot_reset() must set it back after restoring configuration space.

This patch set get_link_status before calling pm_runtime_put() in e1000_open()
to allow e1000_idle() get real link status and schedule first runtime suspend.

This patch also enables wakeup for device if management mode is enabled
(like for WoL) as result pci_prepare_to_sleep() would setup wakeup without
special actions like custom 'enable_wakeup' sign.

Cc: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NBorislav Petkov <bp@suse.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes redundant and unbalanced pci_disable_device() from
__e1000_shutdown(). pci_clear_master() is enough, device can go into
suspended state with elevated enable_cnt.

Bug was introduced in commit 23606cf5
("e1000e / PCI / PM: Add basic runtime PM support (rev. 4)") in v2.6.35

Cc: Bruce Allan <bruce.w.allan@intel.com>
CC: Stable <stable@kernel.org>
Signed-off-by: NKonstantin Khlebnikov <khlebnikov@openvz.org>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: NBorislav Petkov <bp@suse.de>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Dave reported following crash :

general protection fault: 0000 [#1] SMP
CPU 2
Pid: 25407, comm: qemu-kvm Not tainted 3.7.9-205.fc18.x86_64 #1 Hewlett-Packard HP Z400 Workstation/0B4Ch
RIP: 0010:[<ffffffffa0399bd5>]  [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
RSP: 0018:ffff880276913d78  EFLAGS: 00010206
RAX: 50626b6b7876376c RBX: ffff88026e530d68 RCX: ffff88028d158e00
RDX: ffff88026d0d5470 RSI: 0000000000000011 RDI: 0000000000000002
RBP: ffff880276913d88 R08: 0000000000000000 R09: ffff880295002900
R10: 0000000000000000 R11: 0000000000000003 R12: ffffffff81ca3b40
R13: ffffffff8151a8e0 R14: ffff880270875000 R15: 0000000000000002
FS:  00007ff3bce38a00(0000) GS:ffff88029fc40000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00007fd1430bd000 CR3: 000000027042b000 CR4: 00000000000027e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process qemu-kvm (pid: 25407, threadinfo ffff880276912000, task ffff88028c369720)
Stack:
 ffff880156f59100 ffff880156f59100 ffff880276913d98 ffffffff815534f7
 ffff880276913db8 ffffffff8151a74b ffff880270875000 ffff880156f59100
 ffff880276913dd8 ffffffff8151a5a6 ffff880276913dd8 ffff88026d0d5470
Call Trace:
 [<ffffffff815534f7>] nf_conntrack_destroy+0x17/0x20
 [<ffffffff8151a74b>] skb_release_head_state+0x7b/0x100
 [<ffffffff8151a5a6>] __kfree_skb+0x16/0xa0
 [<ffffffff8151a666>] kfree_skb+0x36/0xa0
 [<ffffffff8151a8e0>] skb_queue_purge+0x20/0x40
 [<ffffffffa02205f7>] __tun_detach+0x117/0x140 [tun]
 [<ffffffffa022184c>] tun_chr_close+0x3c/0xd0 [tun]
 [<ffffffff8119669c>] __fput+0xec/0x240
 [<ffffffff811967fe>] ____fput+0xe/0x10
 [<ffffffff8107eb27>] task_work_run+0xa7/0xe0
 [<ffffffff810149e1>] do_notify_resume+0x71/0xb0
 [<ffffffff81640152>] int_signal+0x12/0x17
Code: 00 00 04 48 89 e5 41 54 53 48 89 fb 4c 8b a7 e8 00 00 00 0f 85 de 00 00 00 0f b6 73 3e 0f b7 7b 2a e8 10 40 00 00 48 85 c0 74 0e <48> 8b 40 28 48 85 c0 74 05 48 89 df ff d0 48 c7 c7 08 6a 3a a0
RIP  [<ffffffffa0399bd5>] destroy_conntrack+0x35/0x120 [nf_conntrack]
 RSP <ffff880276913d78>

This is because tun_net_xmit() needs to call nf_reset()
before queuing skb into receive_queue
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John W. Linville says:

====================
This time just passing along a big batch of fixes from Johannes...

For the mac80211 bits:

"Here I have fixes from Ben Greear for stray work items when deleting
interfaces, another idle handling fix from Felix, a fix from Marco ro a
mesh PS buffering crash and I have a fix for the VHT MCS calculation in
association request frames and more nl80211 feature advertising removal
as well as a workaround to increase the dump size if the SKB overhead is
too large. For 3.10 I already have a complete fix queued, but that also
requires (simple) userspace changes."

And for the iwlwifi bits:

"The patches from Dor fix a bunch of calibration issues in the new MVM
driver, and Emmanuel has a number of fixes there as well. Also, we
decided to disable 8k A-MSDU by default, so that's in there. My own
patches are addressing an issue we found with the new devices but that
seems to also exist on older ones, the DMA writeback the devices do can
be delayed and cause issues. The fix is unfortunately relatively large
and depends on two other changes (to not be hugely conflicting), but I
think it's still worth it at this point."

As Johannes says, it is a bit large.  But I hope it is still early
enough in the cycle to make that worthwhile.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SLIPORT_SEMAPHORE register shadowed in the
config-space may not reflect the correct POST stage after
an EEH reset in BE2/3; it may return FW_READY state even though
FW is not ready. This causes the driver to prematurely
poll the FW mailbox and fail.

For BE2/3 use the CSR-BAR/0xac instead.
Reported-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Fix regressions introduced by the last set of fixes (sorry):

1. Potential deadlock when disabling TX queues.
2. RX was broken on architectures other than x86 and powerpc.

I still expect to send one more bug fix for 3.9, but as it sometimes
takes days to reproduce the bug it's going to take a couple of weeks of
testing to be confident that it's really fixed.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX DMA buffers start at an offset of EFX_PAGE_IP_ALIGN bytes from the
start of a cache line.  This offset obviously needs to be included in
the virtual address, but this was missed in commit b590ace0
('sfc: Fix efx_rx_buf_offset() in the presence of swiotlb') since
EFX_PAGE_IP_ALIGN is equal to 0 on both x86 and powerpc.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

efx_device_detach_sync() locks all TX queues before marking the device
detached and thus disabling further TX scheduling.  But it can still
be interrupted by TX completions which then result in TX scheduling in
soft interrupt context.  This will deadlock when it tries to acquire
a TX queue lock that efx_device_detach_sync() already acquired.

To avoid deadlock, we must use netif_tx_{,un}lock_bh().
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

While PCI card faces EEH errors, reset (usually hot reset) is
expected to recover from the EEH errors. After EEH core finishes
the reset, the driver callback (be_eeh_reset) is called and wait
the firmware to complete POST successfully. The original code would
return with error once detecting failure during POST stage. That
seems not enough.

The patch forces the driver (be_eeh_reset) to wait the firmware
completes POST until timeout, instead of returning error upon
detection POST failure immediately. Also, it would improve the
reliability of the EEH funtionality of the driver.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a router forwards a packet that contains the IPv4 timestamp option,
if there is no space left in the option for the router to add its own
timestamp, then the router increments the Overflow value in the option.

However, if the addresses of the routers are prespecified in the option,
then the overflow condition cannot happen: the option is structured so
that each prespecified router has a place to write its timestamp. Other
routers do not add a timestamp, so there will never be a lack of space.

This fix ensures that the Overflow value in the IPv4 timestamp option is
not incremented when the addresses of the routers are prespecified, even
if the Pointer value is greater than the Length value.
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should use time_after_eq() to get maximum latency of two ticks,
instead of three.

Bug added in commit 24f8b238 (net: increase receive packet quantum)
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix new kernel-doc warnings in net/core/dev.c:

Warning(net/core/dev.c:4788): No description found for parameter 'new_carrier'
Warning(net/core/dev.c:4788): Excess function parameter 'new_carries' description in 'dev_change_carrier'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should reset nf settings bond to the skb as ipip/ipgre do.

If not, the conntrack/nat info bond to the origin packet may continually
redirect the packet to vxlan interface causing a routing loop.

this is the scenario:

     VETP     VXLAN Gateway
    /----\  /---------------\
    |    |  |               |
    |  vx+--+vx --NAT-> eth0+--> Internet
    |    |  |               |
    \----/  \---------------/

when there are any packet coming from internet to the vetp, there will be lots
of garbage packets coming out the gateway's vxlan interface, but none actually
sent to the physical interface, because they are redirected back to the vxlan
interface in the postrouting chain of NAT rule, and dmesg complains:

    Mar  1 21:52:53 debian kernel: [ 8802.997699] Dead loop on virtual device vxlan0, fix it urgently!
    Mar  1 21:52:54 debian kernel: [ 8804.004907] Dead loop on virtual device vxlan0, fix it urgently!
    Mar  1 21:52:55 debian kernel: [ 8805.012189] Dead loop on virtual device vxlan0, fix it urgently!
    Mar  1 21:52:56 debian kernel: [ 8806.020593] Dead loop on virtual device vxlan0, fix it urgently!

the patch should fix the problem
Signed-off-by: NZang MingJie <zealot0630@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QFQ+ can select for service only 'eligible' aggregates, i.e.,
aggregates that would have started to be served also in the emulated
ideal system.  As a consequence, for QFQ+ to be work conserving, at
least one of the active aggregates must be eligible when it is time to
choose the next aggregate to serve.

The set of eligible aggregates is updated through the function
qfq_update_eligible(), which does guarantee that, after its
invocation, at least one of the active aggregates is eligible.
Because of this property, this function is invoked in
qfq_deactivate_agg() to guarantee that at least one of the active
aggregates is still eligible after an aggregate has been deactivated.
In particular, the critical case is when there are other active
aggregates, but the aggregate being deactivated happens to be the only
one eligible.

However, this precaution is not needed for QFQ+ to be work conserving,
because update_eligible() is always invoked also at the beginning of
qfq_choose_next_agg(). This patch removes the additional invocation of
update_eligible() in qfq_deactivate_agg().
Signed-off-by: NPaolo Valente <paolo.valente@unimore.it>
Reviewed-by: NFabio Checconi <fchecconi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By definition of (the algorithm of) QFQ+, the system virtual time must
be pushed up only if there is no 'eligible' aggregate, i.e. no
aggregate that would have started to be served also in the ideal
system emulated by QFQ+.  QFQ+ serves only eligible aggregates, hence
the aggregate currently in service is eligible.  As a consequence, to
decide whether there is no eligible aggregate, QFQ+ must also check
whether there is no aggregate in service.
Signed-off-by: NPaolo Valente <paolo.valente@unimore.it>
Reviewed-by: NFabio Checconi <fchecconi@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>