* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  spidernet MAINTAINERship update
  sky2: remove check for PCI wakeup setting from BIOS
  sky2: large memory workaround.
  fs_enet: check for phydev existence in the ethtool handlers
  [usb netdev] asix: fix regression
  r8169: fix missing loop variable increment
  ip1000: menu location change
  Fixed a small typo in the loopback driver
  3c509: PnP resource management fix
  netxen: fix byte-swapping in tx and rx
  netxen: optimize tx handling
  netxen: stop second phy correctly
  netxen: update driver version
  netxen: update MAINTAINERS
  endianness noise in tulip_core
  de4x5 fixes
  xircom_cb endianness fixes
  rt2x00: Put 802.11 data on 4 byte boundary
  rt2x00: Corectly initialize rt2500usb MAC
  rt2x00: Allow rt61 to catch up after a missing tx report

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Fix CPU hotplug when using the SLB shadow buffer
  [POWERPC] efika: add phy-handle property for fec_mpc52xx

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  pnpacpi: print resource shortage message only once
  PM: ACPI and APM must not be enabled at the same time
  ACPI: apply quirk_ich6_lpc_acpi to more ICH8 and ICH9
  ACPICA: fix acpi_serialize hang regression
  ACPI : Not register gsi for PCI IDE controller in legacy mode
  ACPI: Reintroduce run time configurable max_cstate for !CPU_IDLE case
  ACPI: Make sysfs interface in ACPI power optional.
  ACPI: EC: Enable boot EC before bus_scan
  increase PNP_MAX_PORT to 40 from 24

When RPCSEC/GSS and krb5i is used, requests are padded, typically to a multiple
of 8 bytes.  This can make the request look slightly longer than it
really is.

As of

	f34b9568 "The NFSv2/NFSv3 server does not handle zero
		length WRITE request correctly",

the xdr decode routines for NFSv2 and NFSv3 reject requests that aren't
the right length, so krb5i (for example) WRITE requests can get lost.

This patch relaxes the appropriate test and enhances the related comment.
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NJ. Bruce Fields <bfields@citi.umich.edu>
Cc: Peter Staubach <staubach@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

task_ppid_nr_ns is called in three places.  One of these should never
have called it.  In the other two, using it broke the existing
semantics.  This was presumably accidental.  If the function had not
been there, it would have been much more obvious to the eye that those
patches were changing the behavior.  We don't need this function.

In task_state, the pid of the ptracer is not the ppid of the ptracer.

In do_task_stat, ppid is the tgid of the real_parent, not its pid.
I also moved the call outside of lock_task_sighand, since it doesn't
need it.

In sys_getppid, ppid is the tgid of the real_parent, not its pid.
Signed-off-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

pnpacpi: exceeded the max number of IO resources: 40

While this message is a real error and should thus
remain KERN_ERR (even a new dmesg line is seen as a regression
by some, since it was not printed in 2.6.23...) it is certainly
impolite to print this warning 50 times should you happen to
have the oddball system with 90 io resources under a device...

So print the warning just once.

In 2.6.25 we'll get rid of the limits altogether
and these warnings will vanish with them.

http://bugzilla.kernel.org/show_bug.cgi?id=9535Signed-off-by: NLen Brown <len.brown@intel.com>

Acked-by: NLinas Vepstas <linasvepstas@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.

This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch might fix problems with 4G or more of memory.
It stops the driver from doing a small optimization for Tx and Rx,
and instead always sets the high-page on tx/rx descriptors.

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9725Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Way back when (in commit 834f2a4a, aka
"VFS: Allow the filesystem to return a full file pointer on open intent"
to be exact), Trond changed the open logic to keep track of the original
flags to a file open, in order to pass down the the intent of a dentry
lookup to the low-level filesystem.

However, when doing that reorganization, it changed the meaning of
namei_flags, and thus inadvertently changed the test of access mode for
directories (and RO filesystem) to use the wrong flag.  So fix those
test back to use access mode ("acc_mode") rather than the open flag
("flag").

Issue noticed by Bill Roman at Datalight.
Reported-and-tested-by: NBill Roman <bill.roman@datalight.com>
Acked-by: NTrond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: NAl Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Otherwise oops will happen if ethernet device has not been opened:

Unable to handle kernel paging request for data at address 0x0000014c
Faulting instruction address: 0xc016f7f0
Oops: Kernel access of bad area, sig: 11 [#1]
MPC85xx
NIP: c016f7f0 LR: c01722a0 CTR: 00000000
REGS: c79ddc70 TRAP: 0300   Not tainted  (2.6.24-rc3-g820a386b)
MSR: 00029000 <EE,ME>  CR: 20004428  XER: 20000000
DEAR: 0000014c, ESR: 00000000
TASK = c789f5e0[999] 'snmpd' THREAD: c79dc000
GPR00: c01aceb8 c79ddd20 c789f5e0 00000000 c79ddd3c 00000000 c79ddd64 00000000
GPR08: 00000000 c7845b60 c79dde3c c01ace80 20004422 200249fc 000002a0 100da728
GPR16: 100c0000 00000000 00000000 00000000 20022078 00000009 200220e0 bfc85558
GPR24: c79ddd3c 00000000 00000000 c02e0e70 c022fc64 ffffffff c7845800 bfc85498
NIP [c016f7f0] phy_ethtool_gset+0x0/0x4c
LR [c01722a0] fs_get_settings+0x18/0x28
Call Trace:
[c79ddd20] [c79dde38] 0xc79dde38 (unreliable)
[c79ddd30] [c01aceb8] dev_ethtool+0x294/0x11ec
[c79dde30] [c01aaa44] dev_ioctl+0x454/0x6a8
[c79ddeb0] [c019b9d4] sock_ioctl+0x84/0x230
[c79dded0] [c007ded8] do_ioctl+0x34/0x8c
[c79ddee0] [c007dfbc] vfs_ioctl+0x8c/0x41c
[c79ddf10] [c007e38c] sys_ioctl+0x40/0x74
[c79ddf40] [c000d4c0] ret_from_syscall+0x0/0x3c
Instruction dump:
81630000 800b0030 2f800000 419e0010 7c0803a6 4e800021 7c691b78 80010014
7d234b78 38210010 7c0803a6 4e800020 <8003014c> 7c6b1b78 38600000 90040004
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NVitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge branch 'fixes-jgarzik' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 into upstream-fixes

51bf2976 caused a regression in the asix
usbnet driver. usb_control_msg returns the number of bytes read on
success, not 0. Tested with NETGEAR FA120.
Signed-off-by: NRuss Dill <Russ.Dill@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Spotted-by: NCitizen Lee <citizen_lee@thecus.com>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Move the ip1000 driver into the expected place for gigabit cards
in the configuration menu structure. It should be under the gigabit
cards, not at the top level.
Signed-off-by: NStephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This is probably a result of the changes from commit
854d8363 - [NET]: Dynamically allocate the loopback device, part 2
Signed-off-by: NEmil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In order to release PnP resources a card type must be set to EL3_PNP.
Previously, it was never set hence the PnP resources were not
released and device was left in incorrect state.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Here's the reworked patch.

This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.

This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().

This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes bug that doesn't quiesce second port when interface is
brought down, which could lead to unwarranted interrupt during rmmod /
ifdown.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Bumping up driver version to 3.4.18, several fixes have gone in since
version 3.4.2.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Changing MAINTAINERS for netxen nic driver.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* (trivial) endianness annotations
* don't bother with del_timer() from the inside of timer handler itself
* disable_ast() really ought to do del_timer_sync(), not del_timer()
* clean the timer handling in general.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* descriptors inside the rx and tx rings are l-e
* don't cpu_to_le32() the argument of outl()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
  V4L/DVB (7001): av7110: fix section mismatch
  V4L/DVB (6999): ivtv: stick to udelay=10 after all

* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
  [XFS] fix unaligned access in readdir

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6.24:
  sh: Force __access_ok() to obey address space limit.
  sh: Fix argument page dcache flushing regression.

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  [MIPS] Replace 40c7869b kludge
  [MIPS] Lasat: Fix built in separate object directory.
  [MIPS] Malta: Fix software reset on big endian
  [MIPS] pnx8xxx: move to clocksource
  [MIPS] Wrong CONFIG option prevents setup of DMA zone.

Since the introduction of the acquire_console_sem calls in
0333d835, kexecing can cause the
kernel to deadlock:

 ps3fb_shutdown()
  -> unregister_framebuffer()
  -> fb_notifier_call_chain(FB_EVENT_FB_UNBIND)
  -> fbcon_fb_unbind()
  -> unbind_con_driver()
  -> bind_con_driver()
	[ acquires console_sem ]
  -> fbcon_deinit()
  -> fbops->fb_release(newinfo, 0)
  -> ps3fb_release()
  -> ps3fb_sync()
	[ acquires console_sem ]

This change avoids the deadlock by moving the acquire_console_sem()
out of ps3fb_sync(), and puts it into the two other callsites, leaving
ps3fb_release() to call ps3fb_sync() without the console semaphore.

[Geert]
  - Corrected call sequence above
  - ps3fb_release() may be called with and without console_sem held. This is an
    inconsistency that should be fixed at the fb level, but for now, try to
    acquire console_sem in ps3fb_release().

    I think it's safer to let ps3fb_release() try to acquire console_sem and
    not refresh the screen if it fails, than to call ps3fb_sync() without
    holding console_sem, as ps3fb_par may be modified at the same time, causing
    crashes or lockups.

    Besides, ps3fb_release() only calls ps3fb_sync() to refresh the screen
    when display flipping is disabled, which is an uncommon case (except during
    shutdown/kexec).
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In ps3fb_shutdown, freeing the framebuffer will cause fb_info (in
dev->core.driver_data) to be free()ed, which we potentially access
from the ps3fbd kthread.

This change frees the framebuffer after stopping the ps3fbd kthread.
Signed-off-by: NJeremy Kerr <jk@ozlabs.org>
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
  blktrace: kill the unneeded initcall
  block: fix blktrace timestamps
  loop: fix bad bio_alloc() nr_iovec request
  Don't blatt first element of prv in sg_chain()

The bug causes corruptions of data read from flash.

The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer().  Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: NMassimo Cirillo <maxcir@gmail.com>
Signed-off-by: NGiuseppe D'Eliseo <giuseppedeliseo@gmail.com>
Acked-by: NNicolas Pitre <nico@cam.org>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woohouse <dwmw2@infradead.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix oops reported by Trond.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>