for_each_pgdat() was renamed to for_each_online_pgdat() and kerneldoc
comments should be updated accordingly.
Signed-off-by: NFernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes various gpio-related build errors (mostly potential)
reported in part by Russell King and Uwe Kleine-König.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

To keep backwards compatibility, reverse the meanings of these flags so
that when they are not set, the driver uses the original behvaiour.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When we get any IO error during a recovery (rebuilding a spare), we abort
the recovery and restart it.

For RAID6 (and multi-drive RAID1) it may not be best to restart at the
beginning: when multiple failures can be tolerated, the recovery may be
able to continue and re-doing all that has already been done doesn't make
sense.

We already have the infrastructure to record where a recovery is up to
and restart from there, but it is not being used properly.
This is because:
  - We sometimes abort with MD_RECOVERY_ERR rather than just MD_RECOVERY_INTR,
    which causes the recovery not be be checkpointed.
  - We remove spares and then re-added them which loses important state
    information.

The distinction between MD_RECOVERY_ERR and MD_RECOVERY_INTR really isn't
needed.  If there is an error, the relevant drive will be marked as
Faulty, and that is enough to ensure correct handling of the error.  So we
first remove MD_RECOVERY_ERR, changing some of the uses of it to
MD_RECOVERY_INTR.

Then we cause the attempt to remove a non-faulty device from an array to
fail (unless recovery is impossible as the array is too degraded).  Then
when remove_and_add_spares attempts to remove the devices on which
recovery can continue, it will fail, they will remain in place, and
recovery will continue on them as desired.

Issue:  If we are halfway through rebuilding a spare and another drive
fails, and a new spare is immediately available,  do we want to:
 1/ complete the current rebuild, then go back and rebuild the new spare or
 2/ restart the rebuild from the start and rebuild both devices in
    parallel.

Both options can be argued for.  The code currently takes option 2 as
  a/ this requires least code change
  b/ this results in a minimally-degraded array in minimal time.

Cc: "Eivind Sarto" <ivan@kasenna.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In some configurations, a raid6 resync can be limited by CPU speed
(Calculating P and Q and moving data) rather than by device speed.  In
these cases there is nothing to be gained byt serialising resync of arrays
that share a device, and doing the resync in parallel can provide benefit.
 So add a sysfs tunable to flag an array as being allowed to resync in
parallel with other arrays that use (a different part of) the same device.
Signed-off-by: NBernd Schubert <bs@q-leap.de>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Kill the trivial and rather pointless file_path wrapper around d_path.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds a proper extern for mdp_major in include/linux/raid/md.h
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NNeil Brown <neilb@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The atomic_t type is 32bit but a 64bit system can have more than 2^32
pages of virtual address space available.  Without this we overflow on
ludicrously large mappings
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

<linux/types.h> can't be used together with <sys/ustat.h> because they
both define struct ustat:

    $ cat test.c
    #include <sys/ustat.h>
    #include <linux/types.h>
    $ gcc -c test.c
    In file included from test.c:2:
    /usr/include/linux/types.h:165: error: redefinition of 'struct ustat'

has been reported a while ago to debian, but seems to have been
lost in cat fighting: http://bugs.debian.org/429064Signed-off-by: Nmaximilian attems <max@stro.at>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add support for the InstaShield IS-400 four port RS-232 PCI card.
Signed-off-by: NIgnacio García Pérez <iggarpe@t2i.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Parenthesis fix in include/asm-mips/mach-au1x00/au1000.h
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Parenthesis fix in include/asm-mips/gic.h
Signed-off-by: NMariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor rework to support the Intel 5400 chipset.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

OMAP has two include loops in its header files:

  asm-arm/hardware.h <- asm-arm/arch-omap/io.h <-
   asm-arm/arch-omap/hardware.h <- asm-arm/hardware.h

  asm-arm/arch-omap/board-palmte.h <-
   asm-arm/arch-omap/hardware.h <- asm-arm/hardware.h <-
   asm-arm/arch-omap/gpio.h <- asm-arm/arch-omap/board-palmte.h

Circular include dependencies are dangerous since they can result in
inconsistent definitions being provided to other code, especially if
'#ifndef' constructs are used.

Solve these by removing the offending includes, and add additional
includes where necessary.
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

For the simple read_cpuid() macro case the variable processor_id has
no definition on use of the macro. Add an extern for it. Move all the
processor ID macros into the #ifndef __ASSEMBLEY__ block.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The non-MMU case also needs the type definition of pgtable_t.
So move it out of a CONFIG_MMU conditional section.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Compiling ppc64_defconfig with gcc 4.3 gives thes warnings:

arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_get_priority':
arch/powerpc/sysdev/mpic.c:1351: warning: 'is_ipi' may be used uninitialized in this function
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1328: warning: 'is_ipi' may be used uninitialized in this function

It turns out that in the cases where is_ipi is uninitialized, another
variable (mpic) will be NULL and it is dereferenced.  Protect against
this by returning if mpic is NULL in mpic_irq_set_priority, and removing
mpic_irq_get_priority completely as it has no in tree callers.

This has the nice side effect of making the warning go away.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

arch/arm/plat-omap/clock.c:397: warning: "struct cpufreq_frequency_table" declared inside parameter list
arch/arm/plat-omap/clock.c:397: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/plat-omap/clock.c: In function `clk_init_cpufreq_table':
arch/arm/plat-omap/clock.c:402: error: structure has no member named `clk_init_cpufreq_table'
arch/arm/plat-omap/clock.c:403: error: structure has no member named `clk_init_cpufreq_table'
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

collie.h:
     * add some meaningfull names to some gpios
collie.c:
    * initialize cpu registers correctly
Signed-off-by: NThomas Kunze <thommycheck@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If previous window was above representable values of u16,
strange things will happen if undo with the truncated value
is called for. Alternatively, this could be fixed by some
max trickery but that would limit undoing high-speed undos.

Adds 16-bit hole but there isn't anything to fill it with.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Greg Steuck <greg@nest.cx> points out that some of the netfilter
headers can't be used in userspace without including linux/types.h
first. The headers include their own linux/types.h include statements,
these are stripped by make headers-install because they are inside
#ifdef __KERNEL__ however. Move them out to fix this.

Reported and Tested by Greg Steuck.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate feature bits from the NETDEV_FEAT_CHANGE notifier. For now
only TSO is propagated for devices that announce their ability to
support TSO in combination with VLAN accel by setting the NETIF_F_VLAN_TSO
flag.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We want to have the drvdata field set properly when creating the device
as sysfs callbacks can assume it is present and it can race the later
setting of this field.

So, create two new functions, deviec_create_vargs() and
device_create_drvdata() that take this new field.

device_create_drvdata() will go away in 2.6.27 as the drvdata field will
just be moved to the device_create() call as it should be.

Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

vidiocgmbuf() does this:
        mutex_lock(&fh->cap.vb_lock);
        retval = videobuf_mmap_setup(&fh->cap, gbuffers, gbufsize,
                                     V4L2_MEMORY_MMAP);

and videobuf_mmap_setup() then just does
        mutex_lock(&q->vb_lock);
        ret = __videobuf_mmap_setup(q, bcount, bsize, memory);
        mutex_unlock(&q->vb_lock);

which is an obvious double-take deadlock.

This patch fixes this by having vidiocgmbuf() just call the
__videobuf_mmap_setup function instead.
Acked-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Reported-by: NKoos Vriezen <koos.vriezen@gmail.com>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The x86_64 pgd_bad(), pud_bad(), pmd_bad() inlines have differed from
their x86_32 counterparts in a couple of ways: they've been unnecessarily
weak (e.g. letting 0 or 1 count as good), and were typed as unsigned long.
Strengthen them and return int.

The PAE pmd_bad was too weak before, allowing any junk in the upper half;
but got strengthened by the patch correcting its ~PAGE_MASK to ~PTE_MASK.
The PAE pud_bad already said ~PTE_MASK; and since it folds into pgd_bad,
and we don't set the protection bits at that level, it'll do as is.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use PTE_MASK to extract mfn from pte.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use ~PTE_MASK to extract the non-pfn parts of the pte (ie, the pte
flags), rather than constructing an ad-hoc mask.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

_PAGE_CHG_MASK is defined as the set of bits not updated by
pte_modify(); specifically, the pfn itself, and the Accessed and Dirty
bits (which are updated by hardware).
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use PTE_MASK in 3-level pagetables (ie, 32-bit PAE).
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Put the definitions of __(VIRTUAL|PHYSICAL)_MASK before their uses.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the warning:

include2/asm/pgtable.h: In function `pte_modify':
include2/asm/pgtable.h:290: warning: left shift count >= width of type

On 32-bit PAE the virtual and physical addresses are both 32-bits,
so it ends up evaluating 1<<32.  Do the shift as a 64-bit shift then
cast to the appropriate size.  This should all be done at compile time,
and so have no effect on generated code.
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Define PTE_MASK so that it contains a meaningful value for all x86
pagetable configurations.  Previously it was defined as a "long" which
means that it was too short to cover a 32-bit PAE pte entry.

It is now defined as a pteval_t, which is an integer type long enough
to contain a full pte (or pmd, pud, pgd).

This fixes an Xorg crash on 32-bit x86 with PAE due to corruption of the
NX bit in mprotect due to the incorrect type/value of PTE_MASK reported
by Hugh Dickins:

  "Yes, thanks Jeremy: I've checked that each stage builds and runs X on
   my boxes here, x86_32 and x86_32+PAE and x86_64.  (So even 1/8 is
   enough to fix the PAT pte_modify issue, though 2/8 then fixes
   compiler warnings.)"
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Tested-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Since 2.6.25 the HID_QUIRK_APPLE_HAS_FN quirk is enabled even for
non-laptop Apple keyboards of the Aluminium series. The USB version of
these don't need Numlock emulation, like the laptop (and Aluminium
Wireless) do, as they have a proper keypad.

This patch splits the Numlock emulation for Apple keyboards in a
different quirk flag, so that it can be enabled for all the keyboards
but the Aluminium USB ones.

If the Numlock emulation is enabled for Aluminium USB keyboards, the
JKL and UIO keys become the numeric pad, and the rest of the keyboard
is disabled, included the key used to disable Numlock.

Additionally, these keyboard should not have a Numlock at all, as the
Numlock key is instead replaced by the 'Clear' key as usual for Apple
USB keyboards.
Signed-off-by: NDiego 'Flameeyes' Petteno <flameeyes@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

When a cpu really is stuck in the kernel, it can be often
impossible to figure out which cpu is stuck where.  The
worst case is when the stuck cpu has interrupts disabled.

Therefore, implement a global cpu state capture that uses
SMP message interrupts which are not disabled by the
normal IRQ enable/disable APIs of the kernel.

As long as we can get a sysrq 'y' to the kernel, we can
get a dump.  Even if the console interrupt cpu is wedged,
we can trigger it from userspace using /proc/sysrq-trigger

The output is made compact so that this facility is more
useful on high cpu count systems, which is where this
facility will likely find itself the most useful :)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Noticed from Al Viro <viro@ftp.linux.org.uk> via David Miller
<davem@davemloft.net>.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>