- 09 12月, 2009 1 次提交
-
-
由 Tomi Valkeinen 提交于
SMS_ROT_* registers are used by VRFB rotation engine. Signed-off-by: NTomi Valkeinen <tomi.valkeinen@nokia.com> Acked-by: NTony Lindgren <tony@atomide.com> Acked-by: NPaul Walmsley <paul@pwsan.com>
-
- 12 11月, 2009 1 次提交
-
-
由 Kalle Jokiniemi 提交于
The SMS_SYSCONFIG register gets reset in off mode, added a save/restore mechanism for that. Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 21 10月, 2009 1 次提交
-
-
由 Tony Lindgren 提交于
Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 25 7月, 2009 2 次提交
-
-
由 Paul Walmsley 提交于
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum (34xx erratum 1.150) that can cause memory corruption if PWDENA is enabled. Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>. Tested on BeagleBoard rev C2. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
-
由 Jean Pihet 提交于
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: NJean Pihet <jpihet@mvista.com> Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
- 29 5月, 2009 1 次提交
-
-
由 Kevin Hilman 提交于
This patch is to sync the core linux-omap PM code with mainline. This code has evolved and been used for a while the linux-omap tree, but the attempt here is to finally get this into mainline. Following this will be a series of patches from the 'PM branch' of the linux-omap tree to add full PM hardware support from the linux-omap tree. Much of this PM core code was written by Jouni Hogander with significant contributions from Paul Walmsley as well as many others from Nokia, Texas Instruments and linux-omap community. Signed-off-by: NJouni Hogander <jouni.hogander@nokia.com> Cc: Paul Walmsley <paul@pwsan.com> Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
-
- 13 5月, 2009 1 次提交
-
-
由 Paul Walmsley 提交于
Initialize SDRC_POWER to a known-good setting when the kernel boots. Necessary since some bootloaders don't initialize SDRC_POWER properly. Signed-off-by: NPaul Walmsley <paul@pwsan.com>
-
- 09 2月, 2009 2 次提交
-
-
由 Paul Walmsley 提交于
For a given SDRAM clock rate, SDRAM chips require memory controllers to use a specific set of timing minimums and maximums to transfer data reliably. These parameters can be different for different memory chips and can also potentially vary by board. This patch adds the infrastructure for board-*.c files to pass this timing data to the SDRAM controller init function. The timing data is specified in an 'omap_sdrc_params' structure, in terms of SDRC controller register values. An array of these structs, one per SDRC target clock rate, is passed by the board-*.c file to omap2_init_common_hw(). This patch does not define the values for different memory chips, nor does it use the values for anything; those will come in subsequent patches. linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Paul Walmsley 提交于
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an 'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the function names rather than "memory." Mark several functions as static that should not be used outside the sdrc2xxx.c file. linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4. Signed-off-by: NPaul Walmsley <paul@pwsan.com> Signed-off-by: NTony Lindgren <tony@atomide.com> Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-