Next on our list of useless accesses is the maintenance interrupt
status registers (ICH_MISR_EL2, ICH_EISR_EL2).

It is pointless to save them if we haven't asked for a maintenance
interrupt the first place, which can only happen for two reasons:
- Underflow: ICH_HCR_UIE will be set,
- EOI: ICH_LR_EOI will be set.

These conditions can be checked on the in-memory copies of the regs.
Should any of these two condition be valid, we must read GICH_MISR.
We can then check for ICH_MISR_EOI, and only when set read
ICH_EISR_EL2.

This means that in most case, we don't have to save them at all.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Just like on GICv2, we're a bit hammer-happy with GICv3, and access
them more often than we should.

Adopt a policy similar to what we do for GICv2, only save/restoring
the minimal set of registers. As we don't access the registers
linearly anymore (we may skip some), the convoluted accessors become
slightly simpler, and we can drop the ugly indexing macro that
tended to confuse the reviewers.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

The GICD_SGIR register lives a long way from the beginning of
the handler array, which is searched linearly. As this is hit
pretty often, let's move it up. This saves us some precious
cycles when the guest is generating IPIs.
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

So far, we're always writing all possible LRs, setting the empty
ones with a zero value. This is obvious doing a lot of work for
nothing, and we're better off clearing those we've actually
dirtied on the exit path (it is very rare to inject more than one
interrupt at a time anyway).
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order to let make the GICv2 code more lazy in the way it
accesses the LRs, it is necessary to start with a clean slate.

Let's reset the LRs on each CPU when the vgic is probed.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

On exit, any empty LR will be signaled in GICH_ELRSR*. Which
means that we do not have to save it, and we can just clear
its state in the in-memory copy.

Take this opportunity to move the LR saving code into its
own function.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order to make the saving path slightly more readable and
prepare for some more optimizations, let's move the GICH_ELRSR
saving to its own function.

No functional change.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Next on our list of useless accesses is the maintenance interrupt
status registers (GICH_MISR, GICH_EISR{0,1}).

It is pointless to save them if we haven't asked for a maintenance
interrupt the first place, which can only happen for two reasons:
- Underflow: GICH_HCR_UIE will be set,
- EOI: GICH_LR_EOI will be set.

These conditions can be checked on the in-memory copies of the regs.
Should any of these two condition be valid, we must read GICH_MISR.
We can then check for GICH_MISR_EOI, and only when set read
GICH_EISR*.

This means that in most case, we don't have to save them at all.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

GICv2 registers are *slow*. As in "terrifyingly slow". Which is bad.
But we're equaly bad, as we make a point in accessing them even if
we don't have any interrupt in flight.

A good solution is to first find out if we have anything useful to
write into the GIC, and if we don't, to simply not do it. This
involves tracking which LRs actually have something valid there.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Programming the active state in the (re)distributor can be an
expensive operation so it makes some sense to try and reduce
the number of accesses as much as possible. So far, we
program the active state on each VM entry, but there is some
opportunity to do less.

An obvious solution is to cache the active state in memory,
and only program it in the HW when conditions change. But
because the HW can also change things under our feet (the active
state can transition from 1 to 0 when the guest does an EOI),
some precautions have to be taken, which amount to only caching
an "inactive" state, and always programing it otherwise.

With this in place, we observe a reduction of around 700 cycles
on a 2GHz GICv2 platform for a NULL hypercall.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Doing a linear search is a bit silly when we can do a binary search.
Not that we trap that so many things that it has become a burden yet,
but it makes sense to align it with the arm64 code.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

As we're going to play some tricks on the struct coproc_reg,
make sure its 64bit indicator field matches that of coproc_params.
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since we're obviously terrible at sorting the CP tables, make sure
we're going to do it properly (or fail to boot). arm64 has had the
same mechanism for a while, and nobody ever broke it...
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Not having the invariant table properly sorted is an oddity, and
may get in the way of future optimisations. Let's fix it.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Our 64bit sys_reg table is about 90 entries long (so far, and the
PMU support is likely to increase this). This means that on average,
it takes 45 comparaisons to find the right entry (and actually the
full 90 if we have to search the invariant table).

Not the most efficient thing. Specially when you think that this
table is already sorted. Switching to a binary search effectively
reduces the search to about 7 comparaisons. Slightly better!

As an added bonus, the comparison is done by comparing all the
fields at once, instead of one at a time.
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

To configure the virtual PMUv3 overflow interrupt number, we use the
vcpu kvm_device ioctl, encapsulating the KVM_ARM_VCPU_PMU_V3_IRQ
attribute within the KVM_ARM_VCPU_PMU_V3_CTRL group.

After configuring the PMUv3, call the vcpu ioctl with attribute
KVM_ARM_VCPU_PMU_V3_INIT to initialize the PMUv3.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In some cases it needs to get/set attributes specific to a vcpu and so
needs something else than ONE_REG.

Let's copy the KVM_DEVICE approach, and define the respective ioctls
for the vcpu file descriptor.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

To support guest PMUv3, use one bit of the VCPU INIT feature array.
Initialize the PMU when initialzing the vcpu with that bit and PMU
overflow interrupt set.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Acked-by: NPeter Maydell <peter.maydell@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When KVM frees VCPU, it needs to free the perf_event of PMU.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When resetting vcpu, it needs to reset the PMU state to initial status.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When calling perf_event_create_kernel_counter to create perf_event,
assign a overflow handler. Then when the perf event overflows, set the
corresponding bit of guest PMOVSSET register. If this counter is enabled
and its interrupt is enabled as well, kick the vcpu to sync the
interrupt.

On VM entry, if there is counter overflowed and interrupt level is
changed, inject the interrupt with corresponding level. On VM exit, sync
the interrupt level as well if it has been changed.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Reviewed-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

This register resets as unknown in 64bit mode while it resets as zero
in 32bit mode. Here we choose to reset it as zero for consistency.

PMUSERENR_EL0 holds some bits which decide whether PMU registers can be
accessed from EL0. Add some check helpers to handle the access from EL0.

When these bits are zero, only reading PMUSERENR will trap to EL2 and
writing PMUSERENR or reading/writing other PMU registers will trap to
EL1 other than EL2 when HCR.TGE==0. To current KVM configuration
(HCR.TGE==0) there is no way to get these traps. Here we write 0xf to
physical PMUSERENR register on VM entry, so that it will trap PMU access
from EL0 to EL2. Within the register access handler we check the real
value of guest PMUSERENR register to decide whether this access is
allowed. If not allowed, return false to inject UND to guest.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

According to ARMv8 spec, when writing 1 to PMCR.E, all counters are
enabled by PMCNTENSET, while writing 0 to PMCR.E, all counters are
disabled. When writing 1 to PMCR.P, reset all event counters, not
including PMCCNTR, to zero. When writing 1 to PMCR.C, reset PMCCNTR to
zero.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add access handler which emulates writing and reading PMSWINC
register and add support for creating software increment event.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMOVSSET and PMOVSCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMOVSSET or PMOVSCLR register.

When writing non-zero value to PMOVSSET, the counter and its interrupt
is enabled, kick this vcpu to sync PMU interrupt.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMINTENSET and PMINTENCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMINTENSET or PMINTENCLR register.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

These kind of registers include PMEVTYPERn, PMCCFILTR and PMXEVTYPER
which is mapped to PMEVTYPERn or PMCCFILTR.

The access handler translates all aarch32 register offsets to aarch64
ones and uses vcpu_sys_reg() to access their values to avoid taking care
of big endian.

When writing to these registers, create a perf_event for the selected
event type.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

When we use tools like perf on host, perf passes the event type and the
id of this event type category to kernel, then kernel will map them to
hardware event number and write this number to PMU PMEVTYPER<n>_EL0
register. When getting the event number in KVM, directly use raw event
type to create a perf_event for it.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMCNTENSET and PMCNTENCLR is UNKNOWN, use
reset_unknown for its reset handler. Add a handler to emulate writing
PMCNTENSET or PMCNTENCLR register.

When writing to PMCNTENSET, call perf_event_enable to enable the perf
event. When writing to PMCNTENCLR, call perf_event_disable to disable
the perf event.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

These kind of registers include PMEVCNTRn, PMCCNTR and PMXEVCNTR which
is mapped to PMEVCNTRn.

The access handler translates all aarch32 register offsets to aarch64
ones and uses vcpu_sys_reg() to access their values to avoid taking care
of big endian.

When reading these registers, return the sum of register value and the
value perf event counts.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add access handler which gets host value of PMCEID0 or PMCEID1 when
guest access these registers. Writing action to PMCEID0 or PMCEID1 is
UNDEFINED.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Since the reset value of PMSELR_EL0 is UNKNOWN, use reset_unknown for
its reset handler. When reading PMSELR, return the PMSELR.SEL field to
guest.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Add reset handler which gets host value of PMCR_EL0 and make writable
bits architecturally UNKNOWN except PMCR.E which is zero. Add an access
handler for PMCR.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Here we plan to support virtual PMU for guest by full software
emulation, so define some basic structs and functions preparing for
futher steps. Define struct kvm_pmc for performance monitor counter and
struct kvm_pmu for performance monitor unit for each vcpu. According to
ARMv8 spec, the PMU contains at most 32(ARMV8_PMU_MAX_COUNTERS)
counters.

Since this only supports ARM64 (or PMUv3), add a separate config symbol
for it.
Signed-off-by: NShannon Zhao <shannon.zhao@linaro.org>
Acked-by: NMarc Zyngier <marc.zyngier@arm.com>
Reviewed-by: NAndrew Jones <drjones@redhat.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order to merge the KVM/ARM PMU patches without creating a
conflict mess, let's have a temporary include file that won't
conflict with anything. Subsequent patches will clean that up.
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order to ease the merge with the rest of the arm64 tree, move the
definition of __cpu_init_stage2() after what will be the new kvm_call_hyp.
Hopefully the resolution of the merge conflict will be obvious.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

Using the common HYP timer code is a bit more tricky, since we
use system register names. Nothing a set of macros cannot
work around...
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

No need to keep our own private version, the common one is
strictly identical.
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

In order to be able to use the code located in virt/kvm/arm/hyp,
we need to make the global hyp.h file accessible from include/asm,
similar to what we did for arm64.
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>

We already have virt/kvm/arm/ containing timer and vgic stuff.
Add yet another subdirectory to contain the hyp-specific files
(timer and vgic again).
Acked-by: NChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>