- 08 11月, 2011 5 次提交
-
-
由 Takashi Iwai 提交于
The conversion from ALC262 model=benq and model=benq-t31 static configs to auto-parser requires the manual COEF setups for corresponding models. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The static quirks for ALC262 Lenovo 3000 can be covered by the auto- parser with a fixup of the mic-pin to VREF50 and the additional COEF verb. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Use the auto-parser for ALC262 model=toshiba-rx1 with the fixed pin- configs. The BIOS table seems incorrect, so many pin entries are overwritten to match with the former quirk. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Use the auto-parser for ALC262 model=tyan with a pin-config fix-up and drop the static configuration. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When a Realtek codec has a matrix-style capture-source selection, we need to scan all connections instead of only imux items. Otherwise some input might be kept unmuted. Although the corresponding input must be dead so there should be no input from it, it's still safer to mute the route completely. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 06 11月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
The 3.1 kernel has a regression for ALC861 codec where no sound output is heard with the default setup. It's because the amps in DACs aren't properly unmuted while the output mixers are assigned only to pins. This patch fixes the missing initialization of DACs when no mixer is assigned to them. Tested-by: NAndrea Iob <andrea_iob@yahoo.it> Cc: <stable@kernel.org> [v3.1+] Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 04 11月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
Some BIOS report invalid pins as digital output pins. The driver checks the connection but it doesn't do it fully correctly, and it leaves some undefined value as the audio-out widget, which makes the driver spewing warnings. This patch fixes the issue. Reference: https://bugzilla.novell.com/show_bug.cgi?id=727348 Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 03 11月, 2011 2 次提交
-
-
由 Takashi Iwai 提交于
Just clean-up what GCC caught. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When the driver finds multiple ADCs, it tries to create an alternative capture PCM stream. However, these secondary ADCs might be useless or in uncontrolled paths in some cases, e.g. when auto-mic or dynamic ADC-switching is enabled. Also, when only a single capture source is available, the multi-streams don't make sense, too. With this patch, the driver checks such condition and skips the alt stream appropriately. Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 01 11月, 2011 1 次提交
-
-
由 Paul Gortmaker 提交于
Lots of sound drivers were getting module.h via the implicit presence of it in <linux/device.h> but we are going to clean that up. So fix up those users now. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
-
- 27 10月, 2011 2 次提交
-
-
由 Takashi Iwai 提交于
ALC260 has multiple mixer widgets connected to the shared DAC, but the driver currently doesn't check this possibility and ignores when the DAC is shared with others. This resulted in the silent output from some routes because of lack of the amp setup. This patch adds the workaround for it by checking the route even with the shared DAC, but also checking the conflict with the existing control for the very same widget NID. Reference: https://bugzilla.novell.com/show_bug.cgi?id=726812Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The association numbers of surround/CLFE speaker pins aren't correctly mapped by the auto-parser. This patch fixes the CLFE speaker pin to the right assoc value (from 3 to 1). Tested-by: NNika Topolchanskaya <nanodesuu@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 24 10月, 2011 1 次提交
-
-
由 David Henningsson 提交于
The revision 0x100300 was found for ALC662. It seems to work well with patch_alc662. Cc: stable@kernel.org BugLink: http://bugs.launchpad.net/bugs/877373Tested-by: NShengyao Xue <Shengyao.xue@canonical.com> Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Acked-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 21 10月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
When a device has multiple speakers and still has the auto-mute support, the driver copies line_outs[] to speaker_outs[]. And then it tries to assign DACs for both. This ended up with the assignment only to the primary DAC to all speakers. This patch fixes the situation by checking the duplicated LO/SPK case appropriately. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 10月, 2011 4 次提交
-
-
由 Takashi Iwai 提交于
The COEF #0 value represents a sort of device id, so it's supposedly constant while operation. Better to use the cached value instead of reading it at each time from the performance POV. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Use a static table for detecting the codec renames. Also clean up the error paths in each patch_*() function. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Replaced with alc_codec_rename() in all possible places. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 17 10月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
Should be a rare case, but... Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 13 10月, 2011 1 次提交
-
-
由 David Henningsson 提交于
This typo caused headphone pins not to be initialized correctly. BugLink: https://bugs.launchpad.net/bugs/871582 Reported-by: Effenberg Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 06 10月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
When the speaker outputs are more than the headphone outputs, it implies that the system has surround speakers while the headphones are only for monitoring the front. In such a case, it's better to put speakers as the primary outputs so that the driver can build up and keep the surround setup. Otherwise the system will pick up the headphone as primary, and offers less channels than the speakers do support. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 26 9月, 2011 2 次提交
-
-
由 Takashi Iwai 提交于
The spec->autocfg.line_out_pins[] may contain the same pins as hp_pins[] depending on the configuration. When they are identical, detecting the line_jack_present flag screws up the auto-mute because alc_line_automute() is called unconditionally at initialization while it won't be triggered by unsol events, thus the old line_jack_present flag is kept for the whole run. For fixing this buggy behavior, the driver needs to check whether the line-outs are really individual, and skip if same as headphone jacks. Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When the headphone pin is assigned as primary output to line_out_pins[], the automatic HP-pin assignment by ASSID must be suppressed. Otherwise a wrong pin might be assigned to the headphone and breaks the auto-mute. Reference: https://bugzilla.novell.com/show_bug.cgi?id=716104Signed-off-by: NTakashi Iwai <tiwai@suse.de> Cc: <stable@kernel.org>
-
- 21 9月, 2011 1 次提交
-
-
由 David Henningsson 提交于
Increase readability and understandability in the automute code. Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 19 9月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
When the system has only the headphone and the line-out jacks without speakers, the current auto-mute code doesn't work. It's because the spec->automute_lines flag is wrongly referred in update_speakers(). This flag must be meaningless when spec->automute_hp_lo isn't set, thus they should be always coupled. The patch fixes the problem and add a comment to indicate the relationship briefly. BugLink: http://bugs.launchpad.net/bugs/851697Reported-by: NDavid Henningsson <david.henningsson@canonical.com> Tested-By: NJayne Han <jayne.han@canonical.com> Cc: stable@kernel.org (3.0) Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 25 8月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
The rest of ALC662 quirks are only for desktops, and they should work with the auto-parser. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 24 8月, 2011 5 次提交
-
-
由 Takashi Iwai 提交于
When the multi-io jacks are available, parse them first and assign DACs before parsing speakers and headphones. This allows a better chance of surround I/O in some desktops and laptops with limited DACs. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The commit 23c09b00 ALSA: hda - Support multiple speakers by Realtek auto-parser changes the return value from alc_get_line_out_pfx(), and it breaks the center/LFE mixer split check. The caller must test with a string "CLFE" now. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Similarly like ALC662 asus-mode* models, rewrite the laptop-amic and dmic models with the static pin-config tables. Now we can get rid of all alc269_quirks.c. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Re-implement the asus-mode[1-8] quirks with the pin-config tables. They are provided in case where BIOS is broken on the device, so it's not enabled in PCI SSID lookup table. User needs to specify it via model option explicitly if the driver doesn't work with the BIOS setup as is. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 23 8月, 2011 5 次提交
-
-
由 Takashi Iwai 提交于
Let's remove the rest of ALC861 and ALC861-VD quirks. If any breakage is found, it can be fixed easily via the pin-config table update. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
During the cleanup by commit 6727b126, the specific setups for dallas and hp models, using VREF50 for mic pins, were lost. Fixed now. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The internal states, jack_present and line_jack_present should be updated upon unsolicited events even if no automute is set. Otherwise the wrong state is referred when the automute behavior is changed by the mixer control. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When the headphone or speaker output has no own DAC, initialize the path using the primary DAC. Otherwise the path won't be set properly and can result in the silence. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 19 8月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
Add the support of multiple speakers by Realtek auto-parser. When all speaker pins have individual DACs, create each speaker volume control. Otherwise, create a bind-volume control for all speaker outs. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 18 8月, 2011 2 次提交
-
-
由 Takashi Iwai 提交于
These are confirmed to work with the auto-parser with pincfg fixups. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The new parser may use "PCM" volume, but it was missing the vmaster slave list, thus "Master" volume didn't control it. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=41342Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 16 8月, 2011 1 次提交
-
-
由 Takashi Iwai 提交于
Get rid of the rest of ALC268 model quirks. They are all confirmed to work with the auto-parser, too. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-