Implement support for comment entries within choice groups. Comment entries
are displayed visually distinct from normal configs, and selecting them is
a no-op.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>

Our async work synchronization was broken by "async: make sure
independent async domains can't accidentally entangle" (commit
d5a877e8), because it would report
the wrong lowest active async ID when there was both running and
pending async work.

This caused things like no being able to read the root filesystem,
resulting in missing console devices and inability to run 'init',
causing a boot-time panic.

This fixes it by properly returning the lowest pending async ID: if
there is any running async work, that will have a lower ID than any
pending work, and we should _not_ look at the pending work list.

There were alternative patches from Jaswinder and James, but this one
also cleans up the code by removing the pointless 'ret' variable and
the unnecesary testing for an empty list around 'for_each_entry()' (if
the list is empty, the for_each_entry() thing just won't execute).

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=13474Reported-and-tested-by: NChris Clayton <chris2553@googlemail.com>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  MIPS: Outline udelay and fix a few issues.
  MIPS: ioctl.h: Fix headers_check warnings
  MIPS: Cobalt: PCI bus is always required to obtain the board ID
  MIPS: Kconfig: Remove "Support for" from Cavium system type
  MIPS: Sibyte: Honor CONFIG_CMDLINE
  SSB: BCM47xx: Export ssb_watchdog_timer_set

The previous patch submission had a I typo I didn't catch but Bartlomiej
noted. Guess this proves the point about any patch being risky late in an rc
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.30' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: Explicity initialize cpus_hardware_enabled

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
  pdc202xx_old: fix resetproc() method
  pdc202xx_old: fix 'pdc20246_dma_ops'

Outlining fixes the issue were on certain CPUs such as the R10000 family
the delay loop would need an extra cycle if it overlaps a cacheline
boundary.

The rewrite also fixes build errors with GCC 4.4 which was changed in
way incompatible with the kernel's inline assembly.

Relying on pure C for computation of the delay value removes the need for
explicit.  The price we pay is a slight slowdown of the computation - to
be fixed on another day.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make ioctl.h compatible with asm-generic/ioctl.h and userspace

fix the following 'make headers_check' warning:

  usr/include/asm-mips/ioctl.h:64: extern's make no sense in userspace
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Original patch by Imre Kaloz <kaloz@openwrt.org>.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

this patch export ssb_watchdog_timer_set to allow to use it in a Linux 
watchdog driver.
Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr>
Acked-by : Michael Buesch <mb@bu3sch.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5543/1: arm: serial amba: add missing declaration in serial.h
  [ARM] pxa: fix pxa27x_udc default pullup GPIO
  [ARM] pxa/imote2: fix UCAM sensor board ADC model number
  mx[23]: don't put clock lookups in __initdata
  fix oops when using console=ttymxcN with N > 0
  [ARM] ARMv7 errata: only apply fixes when running on applicable CPU
  [ARM] 5534/1: kmalloc must return a cache line aligned buffer

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci-of: Fix the wrong accessor to HOSTVER register
  mvsdio: fix config failure with some high speed SDHC cards
  mvsdio: ignore high speed timing requests from the core
  mmc/omap: Use disable_irq_nosync() from within irq handlers.
  sdhci-of: Add fsl,esdhc as a valid compatible to bind against
  mvsdio: allow automatic loading when modular
  mxcmmc: Fix missing return value checking in DMA setup code.
  mxcmmc : Reset the SDHC hardware if software timeout occurs.
  omap_hsmmc: Trivial fix for a typo in comment
  mxcmmc: decrease minimum frequency to make MMC cards work

Under CONFIG_MAXSMP, cpus_hardware_enabled is allocated from the heap and
not statically initialized.  This causes a crash on reboot when kvm thinks
vmx is enabled on random nonexistent cpus and accesses nonexistent percpu
lists.

Fix by explicitly clearing the variable.

Cc: stable@kernel.org
Reported-and-tested-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NAvi Kivity <avi@redhat.com>

This header is sometimes included in the uncompress stage to get
register values, but no <linux/amba/bus.h> can be included there.
So declare "struct amba_device" here before using it in a prototype.
Signed-off-by: NAlessandro Rubini <rubini@unipv.it>
Acked-by: NAndrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pdc202xx_reset() calls pdc202xx_reset_host() twice, for both channels, while
that function actually twiddles the single, shared software reset bit -- the
net effect is a duplicated reset and horrendous 4 second delay happening not
only on a channel reset but also when dma_lost_irq() and dma_clear() methods
are called.  Fold pdc202xx_reset_host() into pdc202xx_reset(), fix printk(),
and move it before the actual reset...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Commit ac95beed (ide: add struct ide_port_ops
(take 2)) erroneously converted the driver's dma_timeout() and dma_lost_irq()
methods to call the driver's resetproc() method regardless of whether it was
defined for this specific controller while it hadn't been defined and hence
called for PDC20246. So the dma_clear() method, the successor of dma_timeout(),
shouldn't exist and the dma_lost_irq() method should be standard for PDC20246.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
  x86/pci: fix mmconfig detection with 32bit near 4g
  PCI: use fixed-up device class when configuring device

CONFIG_IMA=y inode activity leaks iint_cache and radix_tree_node objects
until the system runs out of memory.  Nowhere is calling ima_inode_free()
a.k.a. ima_iint_delete().  Fix that by calling it from destroy_inode().
Signed-off-by: NHugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  ext3/4 with synchronous writes gets wedged by Postfix
  Fix nobh_truncate_page() to not pass stack garbage to get_block()

* 'upstream-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] pata_ali: Use IGN_SIMPLEX

OK, that's probably the easiest way to do that, as much as I don't like it...
Since iget() et.al. will not accept I_FREEING (will wait to go away
and restart), and since we'd better have serialization between new/free
on fs data structures anyway, we can afford simply skipping I_FREEING
et.al. in insert_inode_locked().

We do that from new_inode, so it won't race with free_inode in any interesting
ways and it won't race with iget (of any origin; nfsd or in case of fs
corruption a lookup) since both still will wait for I_LOCK.
Reviewed-by: N"Theodore Ts'o" <tytso@mit.edu>
Acked-by: NJan Kara <jack@suse.cz>
Tested-by: NDavid Watson <dbwatson@ukfsn.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The nobh_truncate_page() function is used by ext2, exofs, and jfs.  Of
these three, only ext2 and jfs's get_block() function pays attention
to bh->b_size --- which is normally always the filesystem blocksize
except when the get_block() function is called by either
mpage_readpage(), mpage_readpages(), or the direct I/O routines in
fs/direct_io.c.

Unfortunately, nobh_truncate_page() does not initialize map_bh before
calling the filesystem-supplied get_block() function.  So ext2 and jfs
will try to calculate the number of blocks to map by taking stack
garbage and shifting it left by inode->i_blkbits.  This should be
*mostly* harmless (except the filesystem will do some unnneeded work)
unless the stack garbage is less than filesystem's blocksize, in which
case maxblocks will be zero, and the attempt to find out whether or
not the filesystem has a hole at a given logical block will fail, and
the page cache entry might not get zero'ed out.

Also if the stack garbage in in map_bh->state happens to have the
BH_Mapped bit set, there could be an attempt to call readpage() on a
non-existent page, which could cause nobh_truncate_page() to return an
error when it should not.

Fix this by initializing map_bh->state and map_bh->size.

Fortunately, it's probably fairly unlikely that ext2 and jfs users
mount with nobh these days.
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>
Cc: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Some ALi devices report simplex if they have been disabled and re-enabled, and
restoring the byte does not work. Ignore it - the needed supporting logic is
already present for the SATA ULi ports.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: Fix oops and use after free during space balancing
  Btrfs: set device->total_disk_bytes when adding new device

DaVinci clock support has been updated in mainline.
Update clock names accordingly.
Signed-off-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  ata_piix: Add HP Compaq nc6000 to the broken poweroff list
  ahci: add warning messages for hp laptops with broken suspend
  pata_efar: fix PIO2 underclocking
  pata_legacy: wait for async probing

HP Compaq nc6000 suffers from the double disk spindown issue.
Add it to the broken poweroff DMI list.
Signed-off-by: NVille Syrjala <syrjala@sci.fi>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Harddisks on HP dv[4-6] and HDX18 fail to come online after resume on
earlier BIOSen.  Fortunately, HP recently released BIOS updates for
all machines to fix the issue.  Detect old BIOSen, warn the user to
update BIOS on boot and suspend attempts and fail suspend.

Kudos to all the bug reporters.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: kernel.org@epperson.homelinux.net
Cc: emisca@gmail.com
Cc: Gadi Cohen <dragon@wastelands.net>
Cc: Paul Swanson <paul@procursa.com>
Cc: s@ourada.org
Cc: Trevor Davenport <trevor.davenport@gmail.com>
Cc: corruptor1972 <steven_tierney@yahoo.co.uk>
Cc: Victoria Wilson <mail@vwilson.co.uk>
Cc: khiraly <khiraly.list@gmail.com>
Cc: Sean <wollombi@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix the PIO mode 2 using mode 0 timings -- this driver should enable the
fast timing bank starting with PIO2, just like the PIIX/ICH drivers do.
Also, fix/rephrase some comments while at it.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The basic problem here that pata_legacy attaches the host, sees if it found
any devices and detaches it if none were found.  With async probing, it's not
waiting until discovery is finished before deciding it has no devices and
trying the detach leading to this warning:

ata1: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
------------[ cut here ]------------
WARNING: at drivers/ata/libata-core.c:6222 ata_host_detach+0x75/0x90()
Modules linked in:
Pid: 1, comm: swapper Not tainted 2.6.30-rc7 #1
Call Trace:
 [<c01fbb05>] ? ata_host_detach+0x75/0x90
 [<c01fbb05>] ? ata_host_detach+0x75/0x90
 [<c01139b5>] ? warn_slowpath_common+0x45/0x80
 [<c01139fa>] ? warn_slowpath_null+0xa/0x10
 [<c01fbb05>] ? ata_host_detach+0x75/0x90
 [<c02f40e0>] ? legacy_init+0x44e/0x87f
 [<c02f3c92>] ? legacy_init+0x0/0x87f
 [<c0101021>] ? _stext+0x21/0x140
 [<c01890ff>] ? proc_register+0x2f/0x190
 [<c018938c>] ? create_proc_entry+0x5c/0xc0
 [<c0135ebe>] ? register_irq_proc+0x6e/0x90
 [<c02e6484>] ? kernel_init+0x6e/0xbf
 [<c02e6416>] ? kernel_init+0x0/0xbf
 [<c01031d7>] ? kernel_thread_helper+0x7/0x10
---[ end trace ef1ee36e873ae3a0 ]---

Because it detaches before the probe is complete.

One way to fix it would be to put an async_synchronize_full() before looking
for devices, which this patch does.  A better way might be to separate libata
into its own domain and only wait for that.
Reported-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] powernow-k8: check space_id of _PCT registers to be FFH

The powernow-k8 driver checks to see that the Performance Control/Status
Registers are declared as FFH (functional fixed hardware) by the BIOS.
However, this check got broken in the commit:
 0e64a0c9
 [CPUFREQ] checkpatch cleanups for powernow-k8

Fix based on an original patch from Naga Chumbalkar.
Signed-off-by: NNaga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: NDave Jones <davej@redhat.com>

This reverts commit 6c51d1cf, which
apparently causes DRI initialization failures on Radeons.
Reported-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Requested-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The ivtv stream buffers may be for receive or for send but the attached
sg handle is always destined cpu->device.  We flush it correctly but the
allocation is wrongly done with the same type as the buffers.

See bug: http://bugzilla.kernel.org/show_bug.cgi?id=13385

(Note this doesn't close the bug - it fixes the ivtv part and in turn
the logging next shows up some rather alarming DMA sg list warnings in
libata)
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Acked-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 95a3540d ("ptrace_detach: the wrong
wakeup breaks the ERESTARTxxx logic") removed the "extra"
wake_up_process() from ptrace_detach(), but as Jan pointed out this breaks
the compatibility.

I believe the changelog is right and this wake_up() is wrong in many
ways, but GDB assumes that ptrace(PTRACE_DETACH, child, 0, 0) always
wakes up the tracee.

Despite the fact this breaks SIGNAL_STOP_STOPPED/group_stop_count logic,
and despite the fact this wake_up_process() can break another
assumption: PTRACE_DETACH with SIGSTOP should leave the tracee in
TASK_STOPPED case.  Because the untraced child can dequeue SIGSTOP and
call do_signal_stop() before ptrace_detach() calls wake_up_process().

Revert this change for now.  We need some fixes even if we we want to keep
the current behaviour, but these fixes are not for 2.6.30.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Cc: Jan Kratochvil <jan.kratochvil@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The checking of CONFIG_FRAME_WARN in the top level Makefile forgot to
actually derefence the variable thus leading to an always true check.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The "trace || CLONE_PTRACE" check in tracehook_report_clone() is not right,

- If the untraced task does clone(CLONE_PTRACE) the new child is not traced,
  we must not queue SIGSTOP.

- If we forked the traced task, but the tracer exits and untraces both the
  forking task and the new child (after copy_process() drops tasklist_lock),
  we should not queue SIGSTOP too.

Change the code to check task_ptrace() != 0 instead. This is still racy, but
the race is harmless.

We can race with another tracer attaching to this child, or the tracer can
exit and detach in parallel. But giwen that we didn't do wake_up_new_task()
yet, the child must have the pending SIGSTOP anyway.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NRoland McGrath <roland@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
  drm/i915: Remove a bad BUG_ON in the fence management code.