- 03 3月, 2016 1 次提交
-
-
由 Michal Schmidt 提交于
bnx2x crashes during the initialization of the 8021q module on ppc64. The bug is a missing conversion from le32 in bnx2x_handle_classification_eqe() when obtaining the cid value from struct eth_event_data. The fields in struct eth_event_data should all be declared as little-endian and conversions added where missing. Signed-off-by: NMichal Schmidt <mschmidt@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 02 3月, 2016 9 次提交
-
-
由 Sergei Shtylyov 提交于
The 'flags' parameter of the of_phy_connect() function wasn't described in the kernel-doc comment... Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v. but *tsp is also used to traversal transport_addr_list, which will cover the previous value, and make sctp_transport_put work on the wrong transport. So fix it by adding a new variable to get the param *v. Fixes: fba4c330 ("sctp: hold transport before we access t->asoc in sctp proc") Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Xin Long 提交于
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by sctp_cmp_addr_exact(). Now sctp_v6_cmp_addr just check the port when two addresses have different family, and lack the port check for two ipv6 addresses. that will make sctp_hash_cmp() cannot work well. so fix it by adding ports comparison in sctp_v6_cmp_addr(). Signed-off-by: NXin Long <lucien.xin@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Alexandre Belloni says: ==================== phy: micrel: fix issues with interrupt on atmel boards Since the phy is not polled anymore, there were issues getting a link on the sama5d* xplained boards. I'm not too sure about were those fixes should go and I'm wondering whether the first one shoud be made generic. For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I wondering whether this is related to that kind of issue. I had a quick look at the history and could'nt find its use. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexandre Belloni 提交于
Disable auto negotiation on init to properly detect an already plugged cable at boot. At boot, when the phy is started, it is in the PHY_UP state. However, if a cable is plugged at boot, because auto negociation is already enabled at the time we get the first interrupt, the phy is already running. But the state machine then switches from PHY_UP to PHY_AN and calls phy_start_aneg(). phy_start_aneg() will not do anything because aneg is already enabled on the phy. It will then wait for a interrupt before going further. This interrupt will never happen unless the cable is unplugged and then replugged. It was working properly before 321beec5 (net: phy: Use interrupts when available in NOLINK state) because switching to NOLINK meant starting polling the phy, even if IRQ were enabled. Fixes: 321beec5 (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexandre Belloni 提交于
At least on ksz8081, when getting back from power down, interrupts are disabled. ensure they are reenabled if they were previously enabled. This fixes resuming which is failing on the xplained boards from atmel since 321beec5 (net: phy: Use interrupts when available in NOLINK state) Fixes: 321beec5 (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Guillaume Nault 提交于
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl(). In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update ppp->flags while ppp_read() or ppp_poll() is reading it. The update done by ppp_ccp_closed() isn't atomic due to the bit mask operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent readers might get transient values. Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC' test in ppp_read() and ppp_poll(), which in turn can lead to improper decision on whether the PPP unit file is ready for reading or not. Since ppp_ccp_closed() is protected by the Rx and Tx locks (with ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll() to guarantee that ppp_ccp_closed() won't update ppp->flags concurrently. The same reasoning applies to ppp->n_channels. The 'n_channels' field can also be written to concurrently by ppp_ioctl() (through ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't atomic (simple increment/decrement), but are protected by both the Rx and Tx locks (like in the ppp->flags case). So holding the Rx lock before reading ppp->n_channels also prevents concurrent writes. Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ivan Vecera 提交于
Use list_move_tail() to move MAC address entry from list of pending to list of active entries. Simple list_add_tail() leaves the entry also in the first list, this leads to list corruption. Cc: Rasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: NIvan Vecera <ivecera@redhat.com> Acked-by: NRasesh Mody <rasesh.mody@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'linux-can-fixes-for-4.5-20160226' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2016-02-26 this is a pull request of one patch for net. The patch by Maximilain Schneider fixes a kfree() problem during disconnect in the gs_usb driver. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 3月, 2016 1 次提交
-
-
由 Neil Horman 提交于
Recently, I fixed a bug in 3c59x: commit 6e144419 Author: Neil Horman <nhorman@tuxdriver.com> Date: Wed Jan 13 12:43:54 2016 -0500 3c59x: fix another page map/single unmap imbalance Which correctly rebalanced dma mapping and unmapping types. Unfortunately it introduced a new bug which causes oopses on older systems. When mapping dma regions, the last entry for a packet in the 3c59x tx ring encodes a LAST_FRAG bit, which is encoded as the high order bit of the buffers length field. When it is unmapped the LAST_FRAG bit is cleared prior to being passed to the unmap function. Unfortunately the commit above fails to do that masking. It was missed in testing because the system on which I tested it had an intel iommu, the driver for which ignores the size field, using only the DMA address as the token to identify the mapping to be released. However, on older systems that rely on swiotlb (or other dma drivers that key off that length field), not masking off that LAST_FRAG high order bit results in parsing a huge size to be release, leading to all sorts of odd corruptions and the like. Fix is easy, just mask the length with 0xFFF. It should really be &(LAST_FRAG-1), but 0xFFF is the style of the file, and I'd like to make this fix minimal and correct before making it prettier. Appies to the net tree cleanly. All testing on both iommu and swiommu based systems produce good results Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de> CC: "David S. Miller" <davem@davemloft.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 2月, 2016 1 次提交
-
-
由 MINOURA Makoto / 箕浦 真 提交于
When the send skbuff reaches the end, nlmsg_put and friends returns -EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called within a for_each_netdev loop and the first fdb entry of a following netdev could fit in the remaining skbuff. This breaks the mechanism of cb->args[0] and idx to keep track of the entries that are already dumped, which results missing entries in bridge fdb show command. Signed-off-by: NMinoura Makoto <minoura@valinux.co.jp> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 26 2月, 2016 7 次提交
-
-
由 Maximilain Schneider 提交于
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is allocated through alloc_candev() and should instead be freed using free_candev() alone. The inappropriate use of kfree() causes the kernel to hang when gs_destroy_candev() is called. Only the struct gs_usb * which is allocated through kzalloc() should be freed using kfree() when the device is disconnected. Signed-off-by: NMaximilian Schneider <max@schneidersoft.net> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
-
由 Sunil Goutham 提交于
On Thunderx pass 1.x and pass2 due to a HW errata default CQ DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset error when packets are being received at >20Mpps resulting in complete stall of packet reception. This patch will configure it to 0x100 which is what is expected by HW on Thunderx. On future passes of thunderx and other chips HW default/reset value will be 0x100 or higher hence not overwritten. Signed-off-by: NJerin Jacob <jerin.jacob@caviumnetworks.com> Signed-off-by: NSunil Goutham <sgoutham@cavium.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Chun-Hao Lin 提交于
There will be a log spam when there is no cable plugged. Please refer to following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351 https://bugzilla.kernel.org/show_bug.cgi?id=107421 This issue is caused by runtime power management. When there is no cable plugged, the driver will be suspend (runtime suspend) by OS and NIC will be put into the D3 state. During this time, if OS call rtl8169_get_stats64() to dump tally counter, because NIC is in D3 state, the register value read by driver will return all 0xff. This will let driver think tally counter flag is not toggled and then sends the warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)" to kernel log. For fixing this issue, 1.add checking driver's pm runtime status in rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend for counter accuracy in runtime suspend. Signed-off-by: NChunhao Lin <hau@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Linus Lüssing 提交于
We need to update the skb->csum after pulling the skb, otherwise an unnecessary checksum (re)computation can ocure for IGMP/MLD packets in the bridge code. Additionally this fixes the following splats for network devices / bridge ports with support for and enabled RX checksum offloading: [...] [ 43.986968] eth0: hw csum failure [ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2 [ 43.996193] Hardware name: BCM2709 [ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14) [ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90) [ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac) [ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178) [ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188) [ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338) [ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00) [ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c) [...] Fixes: 9afd85c9 ("net: Export IGMP/MLD message validation code") Reported-by: NÁlvaro Fernández Rojas <noltari@gmail.com> Signed-off-by: NLinus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stefan Wahren 提交于
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by qca_spi as it modifies the skb on xmit. Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Stefan Wahren 提交于
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST. So fix this by keeping the flags from ether_setup. Reported-by: NMichael Heimpold <michael.heimpold@i2se.com> Signed-off-by: NStefan Wahren <stefan.wahren@i2se.com> Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Ahern 提交于
Nik pointed that the VRF driver should be using skb_header_pointer instead of accessing skb->data and bits beyond directly which can be garbage. Fixes: 35402e31 ("net: Add IPv6 support to VRF device") Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com> Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 25 2月, 2016 5 次提交
-
-
由 Diego Viola 提交于
The JMC260 network card fails to suspend/resume because the call to jme_start_irq() was too early, moving the call to jme_start_irq() after the call to jme_reset_link() makes it work. Prior this change suspend/resume would fail unless /sys/power/pm_async=0 was explicitly specified. Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351Signed-off-by: NDiego Viola <diego.viola@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 Johannes Berg says: ==================== Another small set of fixes: * stop critical protocol session on disconnect to avoid it getting stuck * wext: fix two RTNL message ordering issues * fix an uninitialized value (found by KASAN) * fix an out-of-bounds access (also found by KASAN) * clear connection keys when freeing them in all cases (IBSS, all other places already did so) * fix expected throughput unit to get consistent values * set default TX aggregation timeout to 0 in minstrel to avoid (really just hide) issues and perform better ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Borkmann 提交于
The fix in 35e2d115 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.") changed behavior for bpf_set_tunnel_key() when in use with IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't. As a result, the stack dropped ingress vxlan IPv6 packets, that have been sent via eBPF through collect meta data mode due to checksum now being zero. Since after LCO, we enable IPv4 checksum by default, so make that analogous and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in IPv4 case. Fixes: 35e2d115 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.") Fixes: c6c33454 ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key") Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net> Acked-by: NAlexei Starovoitov <ast@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Hannes Frederic Sowa 提交于
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL skbs down. This can easily happen with UDP+IPv4 sockets with the first MSG_MORE write smaller than the MTU, second write is a sendfile. Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path, were we calculate the checksum manually during copying. Commit d749c9cb ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets") started to exposes this bug. Fixes: d749c9cb ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets") Reported-by: NJiri Benc <jbenc@redhat.com> Cc: Jiri Benc <jbenc@redhat.com> Reported-by: NWakko Warner <wakko@animx.eu.org> Cc: Wakko Warner <wakko@animx.eu.org> Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Sebastian Frias 提交于
Under some circumstances, e.g. when connecting to a switch, the ethernet port will not be connected to a PHY. In that case a "fixed-link" DT node can be used to replace it. https://stackoverflow.com/questions/31046172/device-tree-for-phy-less-connection-to-a-dsa-switch This patch adds support for the "fixed-link" node to the nb8800 driver. Signed-off-by: NSebastian Frias <sf84@laposte.net> Acked-by: NMans Rullgard <mans@mansr.com> Cc: Mason <slash.tmp@free.fr> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 2月, 2016 4 次提交
-
-
由 Michael Chan 提交于
The arithmetic to zero pad the last 64-bit word in the push buffer is not correct. 1. It should be pdata + length to get to the end. 2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the aligned pointer to void. Pass 'end' which is u64 pointer to PTR_ALIGN() instead so that the aligned pointer - 1 is the last 64-bit pointer to data. Signed-off-by: NMichael Chan <michael.chan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Bernie Harris 提交于
IPCB may contain data from previous layers (in the observed case the qdisc layer). In the observed scenario, the data was misinterpreted as ip header options, which later caused the ihl to be set to an invalid value (<5). This resulted in an infinite loop in the mips implementation of ip_fast_csum. This patch clears IPCB(skb)->opt before dst_link_failure can be called for various types of tunnels. This change only applies to encapsulated ipv4 packets. The code introduced in 11c21a30 which clears all of IPCB has been removed to be consistent with these changes, and instead the opt field is cleared unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to SIT, GRE, and IPIP tunnels. The relevant vti, l2tp, and pptp functions already contain similar code for clearing the IPCB. Signed-off-by: NBernie Harris <bernie.harris@alliedtelesis.co.nz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Konstantin Khlebnikov 提交于
Currently it's converted into msecs, thus HZ=1000 intact. Signed-off-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution") Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Patrik Halfar 提交于
New revison of Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card has new idProduct Bus 002 Device 006: ID 413c:81b3 Dell Computer Corp. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x413c Dell Computer Corp. idProduct 0x81b3 bcdDevice 0.06 iManufacturer 1 Sierra Wireless, Incorporated iProduct 2 Dell Wireless 5809e Gobi™ 4G HSPA+ Mobile Broadband Card iSerial 3 bNumConfigurations 2 Signed-off-by: NPatrik Halfar <patrik_halfar@halfarit.cz> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 2月, 2016 7 次提交
-
-
由 Arend van Spriel 提交于
When user-space has started a critical protocol session and a disconnect event occurs, the rdev::crit_prot_nlportid remains set. This caused a subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by clearing the rdev attribute and call .crit_proto_stop() callback upon disconnect event. Reviewed-by: NHante Meuleman <meuleman@broadcom.com> Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by: NArend van Spriel <arend@broadcom.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Ola Olsson 提交于
The connection keys are zeroed out in all other cases except this one. Let's fix the last one as well. Signed-off-by: NOla Olsson <ola.olsson@sonymobile.com> Reviewed-by: NJulian Calaby <julian.calaby@gmail.com> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
由 Felix Fietkau 提交于
The value 5000 was put here with the addition of the timeout field to ieee80211_start_tx_ba_session. It was originally added in mac80211 to save resources for drivers like iwlwifi, which only supports a limited number of concurrent aggregation sessions. Since iwlwifi does not use minstrel_ht and other drivers don't need this, 0 is a better default - especially since there have been recent reports of aggregation setup related issues reproduced with ath9k. This should improve stability without causing any adverse effects. Cc: stable@vger.kernel.org Acked-by: NAvery Pennarun <apenwarr@gmail.com> Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: "Looks like a lot, but mostly driver fixes scattered all over as usual. Of note: 1) Add conditional sched in nf conntrack in cleanup to avoid NMI watchdogs. From Florian Westphal. 2) Fix deadlock in nfnetlink cttimeout, also from Floarian. 3) Fix handling of slaves in bonding ARP monitor validation, from Jay Vosburgh. 4) Callers of ip_cmsg_send() are responsible for freeing IP options, some were not doing so. Fix from Eric Dumazet. 5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT. 6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot. 7) bcm7xxx PHY driver bug fixes from Florian Fainelli. 8) Avoid unaligned accesses to protocol headers wrt. GRE, from Alexander Duyck. 9) SKB leaks and other problems in arc_emac driver, from Alexander Kochetkov. 10) tcp_v4_inbound_md5_hash() releases listener socket instead of request socket on error path, oops. Fix from Eric Dumazet. 11) Missing socket release in pppoe_rcv_core() that seems to have existed basically forever. From Guillaume Nault. 12) Missing slave_dev unregister in dsa_slave_create() error path, from Florian Fainelli. 13) crypto_alloc_hash() never returns NULL, fix return value check in __tcp_alloc_md5sig_pool. From Insu Yun. 14) Properly expire exception route entries in ipv4, from Xin Long. 15) Fix races in tcp/dccp listener socket dismantle, from Eric Dumazet. 16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not legal. These drivers modify the SKB on transmit. From Jiri Benc. 17) Fix regression in the initialziation of netdev->tx_queue_len. From Phil Sutter. 18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun. 19) SCTP port hash sizing does not properly ensure that table is a power of two in size. From Neil Horman. 20) Fix initializing of software copy of MAC address in fmvj18x_cs driver, from Ken Kawasaki" * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits) bnx2x: Fix 84833 phy command handler bnx2x: Fix led setting for 84858 phy. bnx2x: Correct 84858 PHY fw version bnx2x: Fix 84833 RX CRC bnx2x: Fix link-forcing for KR2 net: ethernet: davicom: fix devicetree irq resource fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address Driver: Vmxnet3: Update Rx ring 2 max size net: netcp: rework the code for get/set sw_data in dma desc soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data net: ti: netcp: restore get/set_pad_info() functionality MAINTAINERS: Drop myself as xen netback maintainer sctp: Fix port hash table size computation can: ems_usb: Fix possible tx overflow Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb net: bcmgenet: Fix internal PHY link state af_unix: Don't use continue to re-execute unix_stream_read_generic loop unix_diag: fix incorrect sign extension in unix_lookup_by_ino bnxt_en: Failure to update PHY is not fatal condition. bnxt_en: Remove unnecessary call to update PHY settings. ...
-
由 Linus Torvalds 提交于
Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fixes from Guenter Roeck: "Two fixes headed for stable: - Remove an unnecessary speed_index lookup for thermal hook in the gpio-fan driver. The unnecessary speed lookup can hog the system. - Handle negative conversion values correctly in the ads1015 driver" * tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook hwmon: (ads1015) Handle negative conversion values correctly
-
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma由 Linus Torvalds 提交于
Pull rdma fixes from Doug Ledford: "One ocrdma fix: - The new CQ API support was added to ocrdma, but they got the arming logic wrong, so without this, transfers eventually fail when they fail to arm the interrupt properly under load Two related fixes for mlx4: - When we added the 64bit extended counters support to the core IB code, they forgot to update the RoCE side of the mlx4 driver (the IB side they properly updated). I debated whether or not to include these patches as they could be considered feature enablement patches, but the existing code will blindy copy the 32bit counters, whether any counters were requested at all (a bug). These two patches make it (a) check to see that counters were requested and (b) copy the right counters (the 64bit support is new, the 32bit is not). For that reason I went ahead and took them" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: IB/mlx4: Add support for the port info class for RoCE ports IB/mlx4: Add support for extended counters over RoCE ports RDMA/ocrdma: Fix arm logic to align with new cq API
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux由 Linus Torvalds 提交于
Pull i2c fixes from Wolfram Sang: "Some bugfixes from I2C for you: A fix for a RuntimePM regression with OMAP, a fix to enable TCO for Lewisburg platforms, and a typo fix while we are here" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: i801: Adding Intel Lewisburg support for iTCO i2c: uniphier: fix typos in error messages i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
-
- 22 2月, 2016 5 次提交
-
-
由 David S. Miller 提交于
Merge tag 'linux-can-fixes-for-4.5-20160221' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2016-02-21 this is a pull reqeust of one patch for net/master. The patch is by Gerhard Uttenthaler and fixes a potential tx overflow in the ems_usb driver. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Yuval Mintz says: ==================== bnx2x: Fix 848xx phys This series contains link-related fixes, mostly for the 848xx phys [2 patches are for 84833, and 2 patches are for 84858]. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Current initialization sequence is lacking, causing some configurations to fail. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yuval Mintz 提交于
The phy's firmware version isn't being parsed properly as it's currently parsed like the rest of the 848xx phys. Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-