- 25 10月, 2010 40 次提交
-
-
由 Heiko Carstens 提交于
Export the cpu configuration topology via sysinfo. Two new lines are introduced: CPU Topology HW: 0 0 0 4 6 4 CPU Topology SW: 0 0 0 0 4 24 The HW line describes the cpu topology nesting levels when the maximum nesting level is used to get the corresponding SYSIB. The SW line describes what Linux is actually using. In this case it supports only two levels (CONFIG_SCHED_BOOK off) and therefore the hardware folded the two lower levels in the SYSIB response block. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Move the topology sysinfo SYSIB definitions to the proper place in asm/sysinfo.h where they should be. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Move cpu topology facility detection to early setup code where it should be. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Store the facility list once at system startup with stfl/stfle and reuse the result for all facility tests. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 FUJITA Tomonori 提交于
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
For the DASD DIAG discipline IO is started through special diagnose calls. Unsolicited interrupts may contain information about the device itself. But this information is not needed because the device is not used directly. Fix the case that an unimplemented dicipline function may be called by ignoring unsolicited interrupts for the DIAG disciplin. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Christian Borntraeger 提交于
Enable PFPO, floating point extension, distinct-operands, fast-BCR-serialization, high-word, interlocked-access, load/store- on-condition, and population-count facilities for guests. (bits 37, 44 and 45). Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Weinhuber 提交于
The dasd interrupt handler needs to distinguish solicited from unsolicited interrupts, as unsolicited interrupts may require special handling (e.g. summary unit checks) and solicited interrupts require proper error recovery for the failed I/O request. The interrupt handler needs to check several bit fields in the interrupt response block (irb) to make this distinction. So far our check of the status control bits has not been specific enough, which may lead to a failed request getting just retried instead of the necessary error recovery. Signed-off-by: NStefan Weinhuber <wein@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Writing to /proc/dasd/statistics while the debug level of the generic dasd debug entry is set to DBF_DEBUG will lead to an use after free when accessing the debug entry later. Since for the format string "%s" in the s390 dbf only a pointer to the string is stored in the debug feature and the buffer used here is freed afterwards. To fix this just remove the debug message. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Christian Borntraeger 提交于
commit 050eef36 [S390] fix tlb flushing vs. concurrent /proc accesses broke KVM on s390x. On every schedule a Badness at include/asm/mmu_context.h:83 appears. s390_enable_sie replaces the mm on the __running__ task, therefore, we have to increase the attach count of the new mm. Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Peter Oberparleiter 提交于
Function ccw_device_cancel_halt_clear may cause an unexpected kernel panic if a clear function is currently active at the subchannel for which it is called. In that case, the iretry counter used to determine the number of retries is never initialized, leading to an immediate failure of the function which results in a kernel panic. Fix this by initializing the iretry counter when the function is first called. Also replace the kernel panic with a return code: a single malfunctioning I/O device should not automatically cause a system-wide kernel panic. Signed-off-by: NPeter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Switch default value of the kernel parameter 'topology' from off to on. Various performance measurements have finally shown that there are no (known) regressions anywhere. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Up to now print_cpu_info() uses the cpu address stored in it's local lowcore to print a message to the console. The cpu address in the lowcore is (in this case) however not the physical cpu address of the local cpu. It's the address of the cpu that issued the sigp restart which started the local cpu. Fix this by using the store cpu address instruction instead. It's not that anybody really cares since this is broken since more than ten years... Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
The ieee_instruction_pointer can not be read from user space anymore since git commit 613e1def, the ptrace interface always returns zero. Remove it from the thread_struct. It is still present in the user_regs_struct for compatability reasons. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Do the setup of the stack overflow argument for the sixth system call parameter right before the branch to the system call function. That simplifies the system call parameter access code. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
The store-cpu-id instruction has a minimum alignment of 8. Reflect that in the definition of struct cpuid. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Read external interrupts parameters from the lowcore in the first level interrupt handler in entry[64].S. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Read all required fields for program checks from the lowcore in the first level interrupt handler in entry[64].S. If the context that caused the fault was enabled for interrupts we can now re-enable the irqs in entry[64].S. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
All architectures besides s390 have pte_mkhuge() defined in pgtable.h. So move the function to pgtable.h on s390 as well. Fixes a compile error introduced with "hugetlb: hugepage migration core" in linux-next which only happens on s390. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Raise SIGBUS with a siginfo structure. Deliver BUS_ADRERR as si_code and the address of the fault in the si_addr field. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
This patch adds a notification mechanism to inform ccw drivers about changes to channel paths, which occured while the device is online. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Update the subchannel descriptor while resuming from hibernate in order to obtain current link addresses. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Update the channel path descriptors after hibernation. This is done unlocked, since we are the only active task at this time. Note: chsc_determine_base_channel_path_desc is changed to use spin_lock_irqsave, since it's called with interrupts disabled in this case. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Update the channel path descriptor at the beginning of to the vary_on operation. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
chsc_determine_channel_path_desc is called by a wrapper who allocates a response struct. The response data is then memcpy'ed to this response struct by chsc_determine_channel_path_desc. Change chsc_determine_base_channel_path_desc to use the global chsc_page and deliver it to the function doing the actual chsc call. The channel path desriptor is then directly read from the response data. As a result we get rid of the additional allocation for the response struct. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Most wrappers around the channel subsystem call have their own logic to allocate memory (with proper alignment) or use preallocated or static memory. This patch converts most users of the channel subsystem call to use the same preallocated page (proteced by a spinlock). Note: The sei_page which is used in our crw handler to call "store event information" has to coexist, since a) in crw context, while accessing the sei_page, sleeping is allowed (which will conflict with the spinlock protection of the chsc_page) b) in crw context, while accessing the sei_page, channel subsystem calls are allowed (which itself would require the page). Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
This patch fixes: * kfree vs. free_page usage * structure definition for determine_css_characteristics * naming convention for the chsc init function * deregistration of crw handlers in the cleanup path Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
Serialize access to members of struct channel_path with a mutex. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
If a ccwdevice is lost during hibernation and a different ccwdevice is attached to the same subchannel, we will deregister the old ccw device and register the new one. Since deregistration is not allowed in this context, we handle this action later. However, some parts of the registration process for the new device were started anyway, so that the old device structure is no longer accessible. Fix this by deferring both actions to the afterwards scheduled subchannel event. Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Andy Shevchenko 提交于
Signed-off-by: NAndy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Stefan Haberland 提交于
The dasd_eckd_dump_sense_dbf function uses a macro for s390 debug feature that can handle up to 8 parameters (for the DASD device driver). Fix the function to use only the maximum number of parameters. Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Sebastian Ott 提交于
fix this sparse warning: drivers/s390/cio/css.c:580:6: warning: symbol 'css_schedule_eval_all_unreg' was not declared. Should it be static? Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Hendrik Brueckner 提交于
If the iucv_register() functions fails, the error recovery calls iucv_unregister() which might cause the following stack backtrace: (<0000000000100ab2> show_trace+0xee/0x144) <00000000004f1842> panic+0xb6/0x248 <00000000001010a6> die+0x15a/0x16c <000000000011d936> do_no_context+0xa6/0xe4 <00000000004f84dc> do_protection_exception+0x2e8/0x3a4 <0000000000113afc> pgm_exit+0x0/0x14 <00000000004e786e> iucv_unregister+0x5a/0x17c (<00000000004e785e> iucv_unregister+0x4a/0x17c) <000000000076de74> hvc_iucv_init+0x228/0x5dc <00000000001000c2> do_one_initcall+0x3e/0x19c <00000000007524a2> kernel_init+0x28e/0x404 <0000000000105dd6> kernel_thread_starter+0x6/0xc <0000000000105dd0> kernel_thread_starter+0x0/0xc Remove the call to iucv_unregister() and remove the goto label as unregistering is the last step in the hvc_iucv initialization. If iucv_register() fails, simply clean up hvc terminals and free resources. Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
When the cmm module is compiled into the kernel it will crash when writing to the R/O data section. Reason is the lower to upper case conversion of the "sender" module parameter which ignored the fact that the pointer is preinitialized. Introduced with 41b42876 "cmm, smsgiucv_app: convert sender to uppercase" Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Joe Perches 提交于
Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
schedule() makes sure that prev != next before calling switch_to(). Therefore remove the redundant check. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
If the previous task was a kernel thread there is no need to save the contents of the fpu and access registers since they aren't used in kernel mode. For the same reason it is not necessary to restore these registers if the next task is a kernel thread. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Add a kernel config option for the IBM zEnterprise 196. This will produce faster code on newer compilers using the -march=z196 option. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Heiko Carstens 提交于
Display machine capacity adjustment indicator and capacity change reason if available in /proc/sysinfo. Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-
由 Martin Schwidefsky 提交于
Add the new instructions introduced with z196 to the kernel disassembler. Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
-