- 10 6月, 2010 1 次提交
-
-
由 Jiri Pirko 提交于
Use call_rcu rather than synchronize_rcu. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 6月, 2010 6 次提交
-
-
由 Eric Dumazet 提交于
- dev_get_by_flags() changed to dev_get_by_flags_rcu() - ipv6_sock_ac_join() dont touch dev & idev refcounts - ipv6_sock_ac_drop() dont touch dev & idev refcounts - ipv6_sock_ac_close() dont touch dev & idev refcounts - ipv6_dev_ac_dec() dount touch idev refcount - ipv6_chk_acast_addr() dont touch idev refcount Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function. [ Fix build with CONFIG_IP_ROUTE_VERBOSE disabled. -DaveM ] Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
in_dev_get() -> __in_dev_get_rcu() in a rcu protected function. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Straightforward conversion to RCU. One rwlock becomes a spinlock, and is static. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Use call_rcu rather than synchronize_rcu. Signed-off-by: NJiri Pirko <jpirko@redhat.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 6月, 2010 20 次提交
-
-
由 jamal 提交于
The extra assertion to allow packet munging only when there are no other ptypes listening which may have worked around an old bug is unnecessary. It is sufficient to check if the skb is cloned before trampling on it. Thanks to Herbert Xu for being persistent and patient in getting this across. [Note that cloning checks and assertions are the general rule used by tc actions (documentation/networking/tc-actions-env-rules.txt)]. Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 jamal 提交于
Now that the core path doesnt set OK to munge we detect writable skbs by looking to see if they are cloned. Signed-off-by: NJamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Changli Gao 提交于
remove two unnecessary assignments we don't need to assign NULL when initialize structure objects. Signed-off-by: NChangli Gao <xiaosuo@gmail.com> ---- net/sched/sch_htb.c | 2 -- 1 file changed, 2 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tobias Klauser 提交于
The memory for the private data is allocated using kzalloc in alloc_etherdev (or alloc_netdev_mq respectively) so there is no need to set the napi member to 0 explicitely. Signed-off-by: NTobias Klauser <tklauser@distanz.ch> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Avoid two atomic ops per raw_send_hdrinc() call Avoid two atomic ops per raw6_send_hdrinc() call Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alex Lorca 提交于
CAIF is using "xxx-AF_MAX" strings for the lock validator. It should use its own strings. Signed-off-by: NAlex Lorca <alex.lorca@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Tom Herbert 提交于
This patch address a serious performance issue in reading the TCP sockets table (/proc/net/tcp). Reading the full table is done by a number of sequential read operations. At each read operation, a seek is done to find the last socket that was previously read. This seek operation requires that the sockets in the table need to be counted up to the current file position, and to count each of these requires taking a lock for each non-empty bucket. The whole algorithm is O(n^2). The fix is to cache the last bucket value, offset within the bucket, and the file position returned by the last read operation. On the next sequential read, the bucket and offset are used to find the last read socket immediately without needing ot scan the previous buckets the table. This algorithm t read the whole table is O(n). The improvement offered by this patch is easily show by performing cat'ing /proc/net/tcp on a machine with a lot of connections. With about 182K connections in the table, I see the following: - Without patch time cat /proc/net/tcp > /dev/null real 1m56.729s user 0m0.214s sys 1m56.344s - With patch time cat /proc/net/tcp > /dev/null real 0m0.894s user 0m0.290s sys 0m0.594s Signed-off-by: NTom Herbert <therbert@google.com> Acked-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
This patch updates the tg3 version to 3.111. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
This patch adds the 5719 PCI device and phy IDs. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
This patch adds the 5719 ASIC revision. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
The driver sometimes needs to know which function number the current device is. This patch changes the code to use devfn over internal register values. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
The 5717 serdes phy brings link up via parallel detection without any additional help from the driver. This patch changes the tg3_setup_fiber_mii_phy() function to detect and allow the use of this feature. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
This patch changes the code to make it legal to allocate only one MSI-X vector. It also fixes a bug where the driver was not checking for error return codes from pci_enable_msix(). Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
The driver was incorrectly programming the indirection table such that rx traffic intended for the second ring went to the first ring, rx traffic intended for the third ring went to the second ring, etc. This patch changes the code so that rx traffic is diverted to the proper ring. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
The rx resources for MSI-X interrupt vector 0 were not being freed correctly. This happens because the teardown loop continue's to the next loop iteration if it detects the tx ring for that vector is not setup, thus bypassing the rx teardown code. This patch moves the call to tg3_rx_prodring_free() earlier in the loop. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
In certain edge conditions, internal tx resources can get corrupted. This patch enables a bit that will fix the problem. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Matt Carlson 提交于
The 5717 and later devices relocate the APE mutex registers. This patch organizes the code so that the driver can use the mutex registers in the old and new locations. Signed-off-by: NMatt Carlson <mcarlson@broadcom.com> Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Conflicts: drivers/net/sfc/net_driver.h drivers/net/sfc/siena.c
-
由 Timo Teräs 提交于
Some configurations need delay between the "write completed" indication and new write to work reliably. Realtek driver seems to use longer delay when polling the "write complete" bit, so it waits long enough between writes with high probability (but could probably break too). This patch adds a new udelay to make sure we wait unconditionally some time after the write complete indication. This caused a regression with XID 18000000 boards when the board specific phy configuration writing many mdio registers was added in commit 2e955856 (r8169: phy init for the 8169scd). Some of the configration mdio writes would almost always fail, and depending on failure might leave the PHY in non-working state. Signed-off-by: NTimo Teräs <timo.teras@iki.fi> Acked-off-by: NFrancois Romieu <romieu@fr.zoreil.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 05 6月, 2010 13 次提交
-
-
由 Shirley Ma 提交于
Enable GRO by default for performance. Signed-off-by: NShirley Ma <xma@us.ibm.com> Acked-by: NGreg Rose <gregory.v.rose@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
With mtu=9000, mld_newpack() use order-2 GFP_ATOMIC allocations, that are very unreliable, on machines where PAGE_SIZE=4K Limit allocated skbs to be at most one page. (order-0 allocations) Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Denis Kirjanov 提交于
This patch compile tested only. Convert legacy PM hooks to dev_pm_ops Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
v2: changed bonding module version, modified to apply on top of changes from previous patch in series, and updated documentation to elaborate on multiqueue awareness that now exists in bonding driver. This patch give the user the ability to control the output slave for round-robin and active-backup bonding. Similar functionality was discussed in the past, but Jay Vosburgh indicated he would rather see a feature like this added to existing modes rather than creating a completely new mode. Jay's thoughts as well as Neil's input surrounding some of the issues with the first implementation pushed us toward a design that relied on the queue_mapping rather than skb marks. Round-robin and active-backup modes were chosen as the first users of this slave selection as they seemed like the most logical choices when considering a multi-switch environment. Round-robin mode works without any modification, but active-backup does require inclusion of the first patch in this series and setting the 'all_slaves_active' flag. This will allow reception of unicast traffic on any of the backup interfaces. This was tested with IPv4-based filters as well as VLAN-based filters with good results. More information as well as a configuration example is available in the patch to Documentation/networking/bonding.txt. Signed-off-by: NAndy Gospodarek <andy@greyhouse.net> Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Andy Gospodarek 提交于
v2: changed parameter name from 'keep_all' to 'all_slaves_active' and skipped setting slaves to inactive rather than creating a new flag at Jay's suggestion. In an effort to suppress duplicate frames on certain bonding modes (specifically the modes that do not require additional configuration on the switch or switches connected to the host), code was added in the generic receive patch in 2.6.16. The current behavior works quite well for most users, but there are some times it would be nice to restore old functionality and allow all frames to make their way up the stack. This patch adds support for a new module option and sysfs file called 'all_slaves_active' that will restore pre-2.6.16 functionality if the user desires. The default value is '0' and retains existing behavior, but the user can set it to '1' and allow all frames up if desired. Signed-off-by: NAndy Gospodarek <andy@greyhouse.net> Signed-off-by: NJay Vosburgh <fubar@us.ibm.com> Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
We can avoid an unecessary cache miss by checking if the skb is non-linear before accessing gso_size/gso_type in skb_warn_if_lro, the same can also be done to avoid a cache miss on nr_frags if data_len is 0. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rami Rosen 提交于
Hi, __pppoe_xmit() in drivers/net/pppoe always returns 1. When the methods fails (via goto abort), it should return 0 and not 1. Regards, Rami Rosen Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
- ipv6 msstab: account for ipv6 header size - ipv4 msstab: add mss for Jumbograms. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
caller: if (!th->rst && !th->syn && th->ack) callee: if (!th->ack) make the caller only check for !syn (common for 3whs), and move the !rst / ack test to the callee. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Florian Westphal 提交于
both syn_flood_warning functions print a message, but ipv4 version only prints a warning if CONFIG_SYN_COOKIES=y. Make the v4 one behave like the v6 one. Signed-off-by: NFlorian Westphal <fw@strlen.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Huang Weiyi 提交于
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
Its better to make a route lookup in appropriate namespace. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
I believe a moderate SYN flood attack can corrupt RFS flow table (rps_sock_flow_table), making RPS/RFS much less effective. Even in a normal situation, server handling short lived sessions suffer from bad steering for the first data packet of a session, if another SYN packet is received for another session. We do following action in tcp_v4_rcv() : sock_rps_save_rxhash(sk, skb->rxhash); We should _not_ do this if sk is a LISTEN socket, as about each packet received on a LISTEN socket has a different rxhash than previous one. -> RPS_NO_CPU markers are spread all over rps_sock_flow_table. Also, it makes sense to protect sk->rxhash field changes with socket lock (We currently can change it even if user thread owns the lock and might use rxhash) This patch moves sock_rps_save_rxhash() to a sock locked section, and only for non LISTEN sockets. Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-