Instead of using the shared area that we be killed.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The driver layer now holds a pointer to the transport,
and shrd->drv is not needed any more, so kill it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

We get two timing related fields for each bss from firmware in scan
results.
1) timestamp - Actual timestamp information in probe response/beacon
2) network_tsf - firmware's TSF value at the time the beacon or probe
response was received.
Both are needed while associating by firmware.

The patch takes care of following things.
1) We should pass "timestamp" to cfg80211_inform_bss(), but currently
"network_tsf" is being provided. This error is corrected here.
2) Rename "network_tsf" to "fw_tsf"
3) Make use of u64 variable instead of an array of u8/u32 to save
parsed "timestamp" information.
4) Use timestamp provided to stack in scan results using
cfg80211_inform_bss() while associating. (bss->tsf)
5) Allocate space to save fw_tsf in "priv" of cfg80211_bss
and retrieve it while associating.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rearrange some code to save extra parameters to the functions.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As described at
http://article.gmane.org/gmane.linux.kernel.wireless.general/86084
libertas is taking a long time to load because it loads firmware
during module loading.

Add a new API for interface drivers to load their firmware
asynchronously. The same semantics of the firmware table are followed
like before.

Interface drivers will be converted in follow-up patches, then we can
remove the old, synchronous firmware loading function.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These simple sanity check avoids extra complexity in error paths when
moving to asynchronous firmware loading (which means the device may fail to
init some time after its creation).
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the ability to pass module parameters with firmware filenames
for USB and SDIO interfaces.

Remove the ability to pass custom "user" filenames to lbs_get_firmware().

Remove the ability to reprogram internal device memory with a different
firmware from the USB driver (we don't know of any users), and simplify
the OLPC firmware loading quirk to simply placing the OLPC firmware
at the top of the list (we don't know of any users other than OLPC).

Move lbs_get_firmware() into its own file.

These simplifications should have no real-life effect but make the
upcoming transition to asynchronous firmware loading considerably less
painful.
Signed-off-by: NDaniel Drake <dsd@laptop.org>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are connection stalls or very poor throughputs with rt2800
hardware using 802.11n in AP mode since patch "mac80211: retry sending
failed BAR frames later instead of tearing down aggr"[1][2].

Since rt2800 hardware is not able to correctly report the tx status of
BAR frames, this patch removes as workaround the existing error handling
on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails.

As a result, most wifi clients (aside from Intel STAs on Windows)
instead will timeout now the reorder buffer and request the lost frame
again.

The correct solution would be, to tear down BA session on AP side.

This patch was born on the basis of "[RFT] rt2x00: Tear down BA
session on QoS frame failure"[3].

Thanks to Helmut Schaa for his support!

[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304
[2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98
[3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569Signed-off-by: NAndreas Hartmann <andihartmann@01019freenet.de>
Acked-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.

Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a corresponding leave call on error failure.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The command strings are needed through the layers for
debug and error messages, but can differ with opmode.
As a result, we need to give the command names to the
transport layer as configuration.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Having a u32 before a potential 64-bit value is
not very efficient, move it last.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

To support hybrid state of MVM op_mode, most of the functioanallity
will be done using DVM functions.

When MVM will have independant live, the declarations will be removed
and the functions will be static back.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Implement mapping of channel to TX power channel group,
for sending channel specific data before add context.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Add a variable for disabling specific calibrations.
Merged old variables for calibrations disabling.
Signed-off-by: NDor Shaish <dor.shaish@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Set size of firmware section in mvm bundle format.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The declaration isn't needed as the struct is only
used in code that includes the right header file.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The code has been changed, move the definitions to the proper file
being used by the code.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This register is used to enable some debug mechanisms.
Signed-off-by: NAmit Beka <amit.beka@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The HCMD_ACTIVE bit is only used in trans.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When WiMax takes over the RF, inform the op_mode.
Signed-off-by: NDon Fry <donald.h.fry@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

It doesn't even exist as a module parameter,
so just remove the item from the struct.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

We've never released firmware using the alternatives
mechanism and our build process makes that difficult
anyway. This means that in every file we have ever
built (except maybe by hand for testing) the listed
alternative was 0. Make the alternative field in the
TLVs part of the TLV number (thus expanding that to
32 bits); this gives us more TLV numbers (not really
needed) and more importantly protects against rogue
firmware files that actually do use the alternatives
mechanism -- those will now be rejected since they
don't contain any valid TLVs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

My original idea with this was to adjust the sleep
pattern of the uCode based on the maximum network
latency userspace asked for. Due to nobody wanting
to test it, this logic was disabled by default. It
seems the time has come to remove it, since it's
not only always disabled but there also don't seem
to be any applications that actually request a max
network latency.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

RT539x devices:
(0x1814, 0x5362)
(0x1814, 0x5392)

Taken from ralink driver 2011_0406_RT5390_RT5392_Linux_STA_V2.5.0.3_DPO
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

put back 0x050d,0x7050 to rt73usb, same usb_id for two chips:

K7SF5D7050A ver 2xxx is rt2500
K7SF5D7050B ver 3xxx is rt73

<http://en-us-support.belkin.com/app/answers/detail/a_id/297/kw/K7SF5D7050>
Signed-off-by: NXose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.

In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.

Also add comments to eeprom_9287.c.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch converts the drivers in drivers/net/wireless/* to use
module_pci_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Simon Kelley <simon@thekelleys.org.uk>
Cc: Jouni Malinen <j@w1.fi>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: linux-wireless@vger.kernel.org
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add utility function to provide the average rssi per vif
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rtl8192ce is in operation, kmemleak indicates a number of leaks, yet
when the driver is removed all are gone. These false positives happen
in two locations:

unreferenced object 0xffff880041124000 (size 9536):
  comm "work_for_cpu", pid 9295, jiffies 4295037203 (age 20596.320s)
  hex dump (first 32 bytes):
    33 00 00 01 01 6d 00 00 00 00 b1 0e 21 0b 00 00  3....m......!...
    01 01 6d 00 00 00 00 8b 20 c0 e9 00 00 01 01 6d  ..m..... ......m
  backtrace:
    [<ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
    [<ffffffff8138d01f>] kmalloc_large_node+0x9a/0xa6
    [<ffffffff811335a5>] __kmalloc_node_track_caller+0x175/0x3b0
    [<ffffffff812ddfe3>] __alloc_skb+0x73/0x230
    [<ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
    [<ffffffffa091a3b7>] rtl_pci_probe+0x10e0/0x17d2 [rtlwifi]
-- snip --
unreferenced object 0xffff8800b4d3f600 (size 256):
  comm "kworker/u:2", pid 13221, jiffies 4297830173 (age 9424.568s)
  hex dump (first 32 bytes):
    1c d6 45 b1 00 88 ff ff 1c d6 45 b1 00 88 ff ff  ..E.......E.....
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff8137a1b1>] kmemleak_alloc+0x21/0x50
    [<ffffffff81130f43>] kmem_cache_alloc_node+0x153/0x270
    [<ffffffff812ddfb6>] __alloc_skb+0x46/0x230
    [<ffffffff812de1b8>] dev_alloc_skb+0x18/0x30
    [<ffffffffa093264a>] rtl92c_set_fw_rsvdpagepkt+0x22a/0x5c0 [rtl8192c_common]
-- snip --
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>