- 07 4月, 2009 1 次提交
-
-
由 Wolfgang Grandegger 提交于
Commit 0f73a449 added I2C device nodes for the LM75 thermal sensor on the TQM85xx modules, unfortunately with the wrong I2C address. The LM75s are located at address 0x48. Signed-off-by: NWolfgang Grandegger <wg@grandegger.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 31 3月, 2009 1 次提交
-
-
由 Kumar Gala 提交于
Older devices tree's used "fsl,85.." instead of the preferred "fsl,mpc85.." for the memory controller & l2 cache controller nodes. The EDAC code is the only use of these and has been updated for some time to support both "fsl,85.." and "fsl,mpc85.." Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 24 3月, 2009 1 次提交
-
-
由 Anton Vorontsov 提交于
Currently it doesn't matter where the mdio nodes are placed, but with power management support (i.e. when sleep = <> properties will take effect), mdio nodes placement will become important: mdio controller is a part of the ethernet block, so the mdio nodes should be placed correctly. Otherwise we may wrongly assume that MDIO controllers are available during sleep. Suggested-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 02 2月, 2009 1 次提交
-
-
由 Wolfgang Grandegger 提交于
Automatic I2C device probing is not done any more. Therefore we need proper DTS device node definitions for the I2C LM75 thermal sensor on the TQM85xx modules. Signed-off-by: NWolfgang Grandegger <wg@grandegger.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 17 12月, 2008 1 次提交
-
-
由 Andy Fleming 提交于
Does the same for the accompanying MDIO driver, and then modifies the TBI configuration method. The old way used fields in einfo, which no longer exists. The new way is to create an MDIO device-tree node for each instance of gianfar, and create a tbi-handle property to associate ethernet controllers with the TBI PHYs they are connected to. Signed-off-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 6月, 2008 1 次提交
-
-
由 Kumar Gala 提交于
Added DMA nodes for the elo/elo-plus DMA engines. Renamed the interrupt controller alias in mpc832x_rdb.dts to ipic so that its the same as all the other boards. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 10 6月, 2008 1 次提交
-
-
由 Wolfgang Grandegger 提交于
Like for the TQM5200, the vendor prefix "tqc," is now used for all TQM85xx modules from TQ-Components GmbH (http://www.tqc.de) in the corresponding DTS files. Signed-off-by: NWolfgang Grandegger <wg@grandegger.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 03 6月, 2008 2 次提交
-
-
由 Kumar Gala 提交于
Added next-level-cache to the L1 and a reference to the new L2 label. This is per the ePAPR 0.94 spec. Since we are't really dependent on this today we aren't supporting the "legacy" l2-cache phandle that is specified in the PPC v2.1 OF Binding spec. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Removed clock-frequency, big-endian, and built-in props as they aren't specified anywhere. Also added compatible = "chrp,open-pic" in the places it was missing. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 28 1月, 2008 3 次提交
-
-
由 Kumar Gala 提交于
* "simple-bus" covers all our needs for of_platform_bus_probe() * make device tree name just 'soc' not 'soc85..' Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-