- 22 10月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
Creative IBG controllers require the playback stream-tags to be started from 1, instead of capture+1. Otherwise the stream stalls. Reported-by: NWai Yew CHAY <wychay@ctl.creative.com> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
The bit value set for TLV mute was wrong in commit de8c85f7, which resulted in bogus dB ranges that screw up PulseAudio. Corrected with the right constant. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 21 10月, 2010 5 次提交
-
-
由 Takashi Iwai 提交于
Multiple Acer laptops with the SSID 1025:04xx require the quirk mode=ideapad, so let's use mask to apply to all these. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Creative HD-audio controller chips require some workarounds: - Additional delay before RIRB response - Set the initial RIRB counter to 0xc0 The latter seems to be done in general in Windows driver, so we may use this value later for all types if it's confirmed to work better. Reported-by: NWai Yew CHAY <wychay@ctl.creative.com> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
The dig_out_nid field must take a digital-converter widget, but the current ca0110 parser passed the pin wrongly instead. Reported-by: NWai Yew CHAY <wychay@ctl.creative.com> Cc: <stable@kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Kailang Yang 提交于
Signed-off-by: NKailang Yang <kailang@realtek.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 19 10月, 2010 1 次提交
-
-
由 Charles 提交于
Windows may leave pin power-down registers set after reboot, and this resulted in muted output on Linux. Reset these registers at initialization properly. Signed-off-by: NCharles Chin <Charles.Chin@idt.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 17 10月, 2010 4 次提交
-
-
由 Takashi Iwai 提交于
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
The HDA specification does not allow for a codec to mute itself just because the volume is reduced, so _of course_ somebody had to go and do it. This wouldn'\''t hurt too much when the volume is adjusted by hand, but programs like PA that try to set the volume automatically could inadvertently mute the output. To work around this, change the TLV dB information for the Master volume on all Sigmatel HDA codecs to indicate the the minimal volume setting actually mutes. Reported-by: NColin Guthrie <gmane@colin.guthr.ie> Reported-by: N"Alexander E. Patrakov" <patrakov@gmail.com> Tested-by: NColin Guthrie <cguthrie@mandriva.org> Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 David Henningsson 提交于
BugLink: http://launchpad.net/bugs/617647 The current SKU value disables playback, so ignore the SKU value. Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 David Henningsson 提交于
Realtek have ways of specifying external amps and more via a special nid or via the Codec's subsystem ID, this is called "SKU". The computer manufacturer sometimes gets this wrong, so we need to be able to override or ignore the SKU customization value. Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 14 10月, 2010 1 次提交
-
-
由 Daniel T Chen 提交于
BugLink: https://bugs.launchpad.net/bugs/656625 Add clause for handling Acer Aspire 8943G's subwoofer as additional speaker pin for automuting. Reported-by: RussianNeuroMancer Cc: stable@kernel.org Signed-off-by: NDaniel T Chen <crimsun@ubuntu.com> Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 12 10月, 2010 1 次提交
-
-
由 David Henningsson 提交于
Position_fix quirks for specific machines now override the default position_fix behavior for all HDA controllers. BugLink: http://launchpad.net/bugs/465942 BugLink: http://launchpad.net/bugs/580749 BugLink: http://launchpad.net/bugs/587546Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 11 10月, 2010 2 次提交
-
-
由 Takashi Iwai 提交于
The input pins on cirrus codecs have also input amps. Let's make control elemetns for them. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Reference: Novell bnc#645066 https://bugzilla.novell.com/show_bug.cgi?id=645066Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 04 10月, 2010 1 次提交
-
-
由 Valentine Sinitsyn 提交于
Signed-off-by: NValentine Sinitsyn <valentine.sinitsyn@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 30 9月, 2010 1 次提交
-
-
由 David Henningsson 提交于
What was previously known as via_dmapos_patch, and hard-coded to be used for VIA and ATI controllers, is now configurable through a module option. The background is that some VIA controllers seem to prefer via_dmapos_patch to be turned off. Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 29 9月, 2010 1 次提交
-
-
由 Luke Yelavich 提交于
BugLink: https://bugs.launchpad.net/ubuntu/+source/alsa-driver/+bug/647374 Set another Acer laptop (SSID 1025:043d) to use CXT5066_IDEAPAD Signed-off-by: NLuke Yelavich <luke.yelavich@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 27 9月, 2010 1 次提交
-
-
由 Otavio Salvador 提交于
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 25 9月, 2010 1 次提交
-
-
由 Vitaliy Kulikov 提交于
Fix bug in switching between dmic and mic when both use the same mux. Signed-off-by: NVitaliy Kulikov <Vitaliy.Kulikov@idt.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 24 9月, 2010 3 次提交
-
-
由 Takashi Iwai 提交于
-
由 Takashi Iwai 提交于
The SPDIF in audio widget must be searched through the list as the widget that contains the given pin as the connection source. The current code was implemented in a reverse way. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Vince Weaver 提交于
I've found the following patch is necessary to enable line-in on my MacBookPro 5,3 machine. With the patch applied I've successfully recorded audio from the line-in jack. This is based on the existing 5,5 support. Signed-off-by: NVince Weaver <vweaver1@eecs.utk.edu> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 21 9月, 2010 7 次提交
-
-
由 Takashi Iwai 提交于
We've applied a fix-up for ALC269 VAIO only for two models. But all Sony VAIO models with ALC269 codec seem to require the similar fix. Let's apply it with vendor-id mask. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
-
由 Takashi Iwai 提交于
The headphone and external-mic pin NIDs can be null, and the jack input elements should be skipped in such a case. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Luke Yelavich 提交于
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/643891 Set the Dell Latitude E6400 (1028:0233) SSID to use AD1984_DELL_DESKTOP Cc: stable@kernel.org Signed-off-by: NLuke Yelavich <luke.yelavich@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Replace the explicit ifdef check and call of check_power_status ops with a new helper function, hda_call_check_power_status(). Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Jerry Zhou 提交于
Channel 2 and channel 3 were all wrongly mapped to HDMI slot 4. This shows up as a bug that one channel is "lost" when playing in surround41 mode. Signed-off-by: NJerry Zhou <jerry.zhou@intel.com> Signed-off-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Wu Fengguang 提交于
DisplayPort works mostly in the same way as HDMI, except that it expects a slightly different audio infoframe format. Citations from "HDA036-A: Display Port Support and HDMI Miscellaneous Corrections": The HDMI specification defines a data island packet with a header of 4 bytes (3 bytes content + 1 byte ECC) and packet body of 32 bytes (28 bytes content and 4 bytes ECC). Display Port specification on the other hand defines a data island packet (secondary data packet) with header of 4 bytes protected by 4 bytes of parity, and data of theoretically up to 1024 bytes with each 16 bytes chunk of data protected by 4 bytes of parity. Note that the ECC or parity bytes are not present in the DIP content populated by software and are hardware generated. It tests DP connection based on the ELD conn_type field, which will be set by the graphics driver and can be overriden manually by users through the /proc/asound/card0/eld* interface. The DP infoframe is tested OK on Intel SandyBridge/CougarPoint platform. Signed-off-by: NWu Fengguang <fengguang.wu@intel.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 20 9月, 2010 6 次提交
-
-
由 Takashi Iwai 提交于
Create a helper function to simplify the code. Also, cleaned up the ifdef SND_HDA_NEEDS_RESUME and CONFIG_SND_HDA_POWER_SAVE. The former is always defined when the latter is set. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
ALC269vb and other variants don't use the widgets 0x24 but prefer the widget 0x22 instead. We need to fix the input parser. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Don't call the COEF check for checking ACL269 codec variants at each time in init but remember the type at the initialization. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When multiple pins are assigned to headphones or speakers, they haven't been initialized properly. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
When quirks are applied, the numbers of output pins in autocfg aren't set up properly but only pin arrays are changed. Let's fix it up so that the rest of the parser can use autocfg.line_outs & co safely. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
This patch merges all three patch_*hdmi variants to the single HDMI parser. There is only one snd-hda-codec-hdmi module now. In this patch, the behavior of each parser isn't changed much. The old ATI parser still doesn't use the dynamic parser yet. In later patches, they'll be cleaned up. Also, this patch gets rid of the individual snd-hda-eld module and builds into snd-hda-codec-hdmi, since this is referred only from the HDMI parser. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 17 9月, 2010 3 次提交
-
-
由 Takashi Iwai 提交于
The external mic jack for auto-mic switch must be really an external jack and with a presense-detection capability. This patch makes the check more paranoia. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Takashi Iwai 提交于
Make the helper function to give the input-pin attribute for jack connectivity and location. This simplifies checks of input-pin jacks a bit in some places. Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 David Henningsson 提交于
It was just a boring day. Signed-off-by: NDavid Henningsson <david.henningsson@canonical.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-