This is a hack that seems to kick start the 2D engine of the Savage IX in some
Toshiba laptops.  Without this, the laptop starts with a black screen and
occasionally crashes X.
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pixclock setting in sstfb didn't work with my Voodoo 2 card with ICS 5342 DAC
(this DAC requires two consecutive writes to one of its registers to program
pixclock - maybe first write merged with second).
Signed-off-by: NOndrej Zajicek <santiago@crfreenet.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ...  among other things, it can be some time before
a driver is ready.  This patch corrects that oversight, fixing

 - documentation
 - platforms supporting the GPIO interface
 - users of that call (just one for now, others are pending)

There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.

Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ...  so those chips might not avoid the glitches.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NAndrew Victor <andrew@sanpeople.com>
Acked-by: NMilan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix a bug in the cleanup of an spi_bitbang bus.

The workqueue associated with the bus was destroyed before the call to
spi_unregister_master.  That meant that spi devices on that bus would be
unable to do IO in their remove method.  The shutdown flag should have been
able to prevent a segfault, but was never getting set.  By waiting to
destroy the workqueue until after the master is unregistered, devices are
able to do IO in their remove methods.  An added benefit is that neither
the shutdown flag nor a wait for the queue of messages to empty is needed.
Signed-off-by: NChris Lesiak <chris.lesiak@licor.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes a user-triggerable oops that was reported by Leonid
Ananiev as archived at http://lkml.org/lkml/2007/2/8/337.

dio writes invalidate clean pages that intersect the written region so that
subsequent buffered reads go to disk to read the new data.  If this fails
the interface tries to tell the caller that the cache is inconsistent by
returning EIO.

Before this patch we had the problem where this invalidation failure would
clobber -EIOCBQUEUED as it made its way from fs/direct-io.c to fs/aio.c.
Both fs/aio.c and bio completion call aio_complete() and we reference freed
memory, usually oopsing.

This patch addresses this problem by invalidating before the write so that
we can cleanly return -EIO before ->direct_IO() has had a chance to return
-EIOCBQUEUED.

There is a compromise here.  During the dio write we can fault in mmap()ed
pages which intersect the written range with get_user_pages() if the user
provided them for the source buffer.  This is a crazy thing to do, but we
can make it mostly work in most cases by trying the invalidation again.
The compromise is that we won't return an error if this second invalidation
fails if it's an AIO write and we have -EIOCBQUEUED.

This was tested by having two processes race performing large O_DIRECT and
buffered ordered writes.  Within minutes ext3 would see a race between
ext3_releasepage() and jbd holding a reference on ordered data buffers and
would cause invalidation to fail, panicing the box.  The test can be found
in the 'aio_dio_bugs' test group in test.kernel.org/autotest.  After this
patch the test passes.
Signed-off-by: NZach Brown <zach.brown@oracle.com>
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Cc: Leonid Ananiev <leonid.i.ananiev@linux.intel.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

madvise(MADV_REMOVE) can go into an infinite loop or cause an oops if the
call covers a region from the start of a vma, and extending past that vma.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: NHugh Dickins <hugh@veritas.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During modification of code to support UFS2 writing, the case with
"three indirect" blocks in truncate path was missed, this patch fixes
this situation.
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fix behaviour in such test scenario:

  lseek(fd, BIG_OFFSET)
  write(fd, buf, sizeof(buf))
  truncate(BIG_OFFSET)
  truncate(BIG_OFFSET + sizeof(buf))
  read(fd, buf...)

Because of if file big enough(BIG_OFFSET) we start allocate space by block,
ordinary block size > page size, so we should zeroize the rest of block in
truncate(except last framgnet, about which VFS should care), to not get
garbage, when we extend file.

Also patch corrects conversion from pointer to block to physical block number,
this helps in case of not common used UFS types.

And add to debug output inode number.
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes "change blocks numbers on the fly" in case when "prepare
write page" is in the call chain, in this case some buffers may be not
uptodate and not mapped, we should care to map them and load from disk.

This patch was tested with:
 - ufs regressions simple tests
 - fsx-linux
 - ltp(20060306)
 - untar and build kernel
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch corrects work with time in UFS2 case.

1) According to UFS2 disk layout modification/access and so on "time"
   should be hold in two variables one 64bit for seconds and another 32bit for
   nanoseconds,

   at now for some unknown reason we suppose that "inode time" holds in
   three variables 32bit for seconds, 32bit for milliseconds and 32bit for
   nanoseconds.

2) We set amount of nanoseconds in "VFS inode" to 0 during read, instead of
   getting values from "on disk inode"(this should close
   http://bugzilla.kernel.org/show_bug.cgi?id=7991).
Signed-off-by: NEvgeniy Dushistov <dushistov@mail.ru>
Cc: Bjoern Jacke <bjoern@j3e.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Prevent the WARN_ON() in arch/x86_64/kernel/acpi/sleep.c:init_low_mapping()
from triggering by disabling nonboot CPUs before we finally enter the
platform suspend.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If swsusp is using the platform mode during the resume and the image cannot
be read, the platform mode should be switched off before software_resume()
returns.  Make it happen.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This removes several pointless exports from drivers/dma/dmaengine.c; the
dma_async_memcpy_*() functions are inlined by <linux/dmaengine.h> so those
exports are inappropriate.

It also moves the existing EXPORT_SYMBOL declarations next to their functions,
so it's now trivial to confirm one-to-one correspondence between exports and
nonstatic symbols.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When iterating through an array, one must be careful to test one's index
variable rather than another similarly-named variable.

The loop will read off the end of conf->disks[] in the following
(pathological) case:

  % dd bs=1 seek=840716287 if=/dev/zero of=d1 count=1
  % for i in 2 3 4; do dd if=/dev/zero of=d$i bs=1k count=$(($i+150)); done
  % ./vmlinux ubd0=root ubd1=d1 ubd2=d2 ubd3=d3 ubd4=d4
  # mdadm -C /dev/md0 --level=linear --raid-devices=4 /dev/ubd[1234]

adding some printks, I saw this:

  [42949374.960000] hash_spacing = 821120
  [42949374.960000] cnt          = 4
  [42949374.960000] min_spacing  = 801
  [42949374.960000] j=0 size=820928 sz=820928
  [42949374.960000] i=0 sz=820928 hash_spacing=820928
  [42949374.960000] j=1 size=64 sz=64
  [42949374.960000] j=2 size=64 sz=128
  [42949374.960000] j=3 size=64 sz=192
  [42949374.960000] j=4 size=1515870810 sz=1515871002

Cc: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: NNeil Brown <neilb@cse.unsw.edu.au>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make some normal code paths in PNP stop issuing syslog spam.  Since PNP
issues calls regardless of device capablities, it's no surprise when some
of those devices don't support those calls!
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  natsemi: Avoid IntrStatus lossage if RX state machine resets.
  natsemi: Fix NAPI for interrupt sharing
  natsemi: Consistently use interrupt enable/disable functions
  NetXen: Fix softlockup seen during hardware access
  NetXen: Bug fix for Jumbo frames on XG card
  skge: set mac address bonding fix

This patch (as869) reinstates the mutual exclusion between sysfs
attribute method calls and attribute unregistration.  The
previously-reported deadlocks have been fixed, and this exclusion is
by far the simplest way to avoid races during driver unbinding.

The check for orphaned read-buffers has been moved down slightly, so
that the remainder of a partially-read buffer will still be available
to userspace even after the attribute has been unregistered.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as868) adds a helper routine for device drivers that need
to set up a callback to perform some action in a different process's
context.  This is intended for use by attribute methods that want to
unregister themselves or their parent device.  Attribute method calls
are mutually exclusive with unregistration, so such actions cannot be
taken directly.

Two attribute methods are converted to use the new helper routine: one
for SCSI device deletion and one for System/390 ccwgroup devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
  HID: zeroing of bytes in output fields is bogus
  HID: allocate hid_parser in a proper way

This patch fixes the poll routine for the natsemi driver so that if the
driver detects an RX state machine lockup then no interrupts will be
lost while the driver recovers from that.
Signed-Off-By: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The interrupt status register for the natsemi chips is clear on read and
was read unconditionally from both the interrupt and from the NAPI poll
routine, meaning that if the interrupt service routine was called (for
example, due to a shared interrupt) while a NAPI poll was scheduled
interrupts could be missed.  This patch fixes that by ensuring that the
interrupt status register is only read by the interrupt handler when
interrupts are enabled from the chip.

It also reverts a workaround for this problem from the netpoll hook and
improves the trace for interrupt events.

Thanks to Sergei Shtylyov <sshtylyov@ru.mvista.com> for spotting the
issue, Mark Huth <mhuth@mvista.com> for a simpler method and Simon
Blake <simon@citylink.co.nz> for testing resources.
Signed-Off-By: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The natsemi drivers include functions for enabling and disabling
interrupts from the chip but these are not used in all code paths.  This
patch changes the code paths that touch the interrupt enable register to
use the functions.  In all cases this adds an extra PCI read to post the
operation but since none of these are in fast paths this shouldn't be
too much of a problem.
Signed-Off-By: NMark Brown <broonie@sirena.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: This will fix a softlock seen on some machines.
The reason was too much time was spent waiting for hardware access
to go through.

Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

NetXen: Set the MTU for the right port depending upon the port number
for XG cards.

Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When bonding does fail over it calls set_mac_address.  When this happens
as the result of another port going down, the phy_mutex that is common to
both ports is held, so it deadlocks. Setting the address doesn't need to do
anything that needs the phy_mutex, it already has the RTNL to protect against
other admin actions.

This change just disables the receiver to avoid any hardware confusion
while address is changing.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This reverts commit 6ebf622b and
replaces it with one that actually works.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/mfasheh/ocfs2:
  ocfs2_dlm: Add missing locks in dlm_empty_lockres
  ocfs2_dlm: Missing get/put lockres in dlm_run_purge_lockres
  configfs: add missing mutex_unlock()
  ocfs2: add some missing address space callbacks
  ocfs2: Concurrent access of o2hb_region->hr_task was not locked
  ocfs2: Proper cleanup in case of error in ocfs2_register_hb_callbacks()

* master.kernel.org:/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
  [WATCHDOG] i8xx TCO driver - mark for removal

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

NB: driver is choke-full of code that will break on big-endian; as long
as the hardware is onboard-only we can live with that, but sooner or
later that'll need fixing.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Acked-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>