At some point during Linux 2.1 development, ioremap() gained the ability
to handle addresses which weren't page-aligned.  Also expand the CONFIG_PCI
range to encompass that entire section of wide board initialisation, since
all wide boards are PCI.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

By moving a test from AscGetChipBusType into its only caller, we can delete
the whole function
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Remove some useless forward declarations
Reformat some comments, debug messages, and the occasional piece of real code
Removal of unnecessary braces
Remove duplicate setting of shost->irq
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Use slave_configure() to do all the work that used to be done in
AscInquiryHandling and AdvInquiryHandling.  Split slave_configure into
two functions, one for wide and one for narrow controllers.

Remove some unused definitions, duplicate definitions, unnecessary
declarations, and scsireqq, cap_info and inquiry from struct asc_board.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

According to the AdvanSys driver, this device has a problem with tagged
queueing.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

AscCompareString() is just another name for strncmp
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Remove wrappers around the PCI configuration space accessors
 - Call pci_set_master() instead of poking at config space directly
 - Move the latency setting into one function called for both narrow and
   wide boards.
 - Tidy up AdvInitGetConfig() a little.
 - Delete a few unused prototypes and definitions.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Make sure the resources are reserved and released by all the callers of
advansys_board_found().  This eliminates the check_region-style race.
It also allows us to use the pci_request_regions() API.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Register two isa_drivers, one for ISA and one for VLB, in order to
preserve detection order.  When deleting advansys_detect, we lose the
last vestiges of the code that limited IO port scanning.  This code
has been effectively disabled for many years anyway; I'll restore it
in a module_param later.  We also lose the code that placed all ISA PnP
cards into WaitForKey state -- drivers shouldn't be doing this anyway.
The asc_host array goes away too.  Also remove some IOADR and other
definitions, such as ASC_NUM_BOARD_SUPPORTED.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Switch EISA probing to the driver model
 - Remove some now-unused macros and functions
 - Update the FIXME now that we use the correct driver model probing API
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Add a pci_driver interface for the PCI advansys devices (for
   ISA/EISA/VLB devices, we still call advansys_detect).
 - Many functions are converted from __init to __devinit to allow hotplug
   PCI to work.
 - Only keep devices found by advansys_detect in the asc_host list.
 - Rename asc_board_count to asc_legacy_count.  New asc_board_count is only
   used to generate a unique name for each device.
 - Remove some now-unused macros and struct definitions
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Switch from scsi_register/scsi_unregister to scsi_host_alloc,
   scsi_add_host, scsi_scan_host and scsi_host_put.
 - Rename the scsi_host_template to advansys_template
 - Use module_init and module_exit instead of scsi_module.c
 - Remove protection against advansys_detect being called twice
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

 - Put all the error cleanup at the end of the function and goto the
   appropriate label
 - Split advansys_wide_init_chip out of advansys_board_found
 - Split advansys_wide_free_mem out of advansys_board_found.  Use it
   from advansys_release
 - Use GFP_KERNEL, not GFP_ATOMIC, when allocating memory during
   initialisation
 - Eliminate lots of PROC_FS ifdefs by removing the ifdefs around the prtbuf
   struct member
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The interrupt routines used to walk the list of Scsi_Hosts belonging to
this driver to make sure that the scsi_cmnd belonged to one of them.
This is a waste of time and gets in the way of later cleanups, so
delete it.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Pass the Scsi_Host to the interrupt handler, rather than polling all
hosts for each interrupt.
Return IRQ_NONE if we didn't handle this interrupt
Don't set the IRQF_DISABLED flag; this is not a fast-executing interrupt
handler.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Just use the Scsi_Host passed in, rather than looking through the driver's
own array of boards for one that matches it.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Update the version to 3.4
Add my copyright
Add myself to MAINTAINERS
Exercise my right to change the license from dual BSD/GPL to GPL
Don't force the definition of CONFIG_ISA on x86
Always include pci.h
Stop including stat.h
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

unsigned short is too small for sizeof(struct scatterlist) *
min(q->max_hw_segments, q->max_phys_segments).

This fixes memory leak with 4096 segments since 16 (likely sg size
with x86) * 4096 sets sglist_len to zero.

This might not happen without sg chaining support.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NDouglas Gilbert <dougg@torque.net>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Stress-testing and some thought has revealed some places where
asynchronous scanning needs some more attention to locking.

 - Since async_scan is a bit, we need to hold the host_lock while
   modifying it to prevent races against other CPUs modifying the word
   that bit is in.  This is probably a theoretical race for the moment,
   but other patches may change that.
 - The async_scan bit means not only that this host is being scanned
   asynchronously, but that all the devices attached to this host are not
   yet added to sysfs.  So we must ensure that this bit is always in sync.
   I've chosen to do this with the scan_mutex since it's already acquired
   in most of the right places.
 - If the host changes state to deleted while we're in the middle of
   a scan, we'll end up with some devices on the host's list which must
   be deleted.  Add a check to scsi_sysfs_add_devices() to ensure the
   host is still running.
 - To avoid the async_scan bit being protected by three locks, the
   async_scan_lock now only protects the scanning_list.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

  - use scsi_cmnd data accessors
  - Clean the !use_sg code paths
Signed-off-by: NBoaz Harrosh <bharrosh@panasas.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
[jejb: merge conflict fix]
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

sg's may have setup a the buffer with a different length than
the transfer length so we should be using the bufflen passed
in as the request's data len.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This converts ps3rom driver to use the new accessors for the sg lists
and the parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

it's better to remove tgt dependencies in srp transport class since
most people want only initiator support.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This converts ibmvstgt to use transport tsk_mgmt_response callback.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This moves tsk_mgmt_response callback in struct scsi_host_template to
struct scsi_transport_template since struct scsi_transport_template is
more suitable for the task management stuff.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This converts libsrp and ibmvstgt to use srp transport.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This adds minimum target driver support:

- srp_rport_{add,del} calls scsi_tgt_it_nexus_{create,destroy} for
target drivers.

- add a callback to notify target drivers of the nexus operation
results to srp_function_template.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

tgt uses scsi_host as I_T nexus. This works for ibmvstgt because it
creates one scsi_host for one initiator. However, other target drivers
don't work like that.

This adds I_T nexus support, which enable one scsi_host to handle
multiple initiators. New scsi_tgt_it_nexus_create/destroy functions
are expected be called transport classes. For example, ibmvstgt
creates an initiator remote port, then the srp transport calls
tgt_it_nexus_create. tgt doesn't manages I_T nexus, instead it tells
tgtd, user-space daemon, to create a new I_T nexus.

On the receiving the response from tgtd, tgt calls
shost->transportt->it_nexus_response. transports should notify a
lld. The srp transport uses it_nexus_response callback in
srp_function_template to do that.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This adds a 'roles' attribute to rport like transport_fc. The role can
be initiator or target. That is, the initiator driver creates target
remote ports and the target driver creates initiator remote ports.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This converts ib_srp to use the srp transport class.

I don't have ib hardware so I've not tested this patch.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This converts ibmvscsi to use the srp transport class.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This adds srp transport class that works with ib_srp and ibmvscsi.

It creates only /sys/class/{srp_host,srp_remote_ports} and
srp_remote_ports has only "port_id" attribute.

viola:/sys/class/srp_remote_ports/port-0:1# ls
device  port_id  subsystem  uevent
viola:/sys/class/srp_remote_ports/port-0:1# cat port_id
4c:49:4e:55:58:20:56:49:4f:00:00:00:00:00:00:00
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Original implementation manipulated the FC_GS values for
port-speed.  Transition the codes to use the driver's own
internal representations as this makes for a reduction in
duplicate 'conversion' codes throughout the driver.
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Transitioning link-state via NOS/OLS requires a relogin to a
fabric's Management Server.  Request relogin when the firmware
issues a point-to-point asynchronous event (0x8030).
Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Fix the data buffer accessor patch.

For request without a data buffer nothing was written into
a SBALE.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

allocate gid_pn_data objects from gid_pn_cache.

Allocate gid_pn_data objects from the corresponding cache which ensures
proper alignment.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>