- 02 8月, 2015 3 次提交
-
-
git://git.infradead.org/users/vkoul/slave-dma由 Linus Torvalds 提交于
Pull dmaengine fixes from Vinod Koul: "We had a regression due to reuse of descriptor so we have reverted that. The rest are driver fixes: - at_hdmac and at_xdmac for residue, trannfer width, and channel config - pl330 final fix for dma fails and overflow issue - xgene resouce map fix - mv_xor big endian op fix" * tag 'dmaengine-fix-4.2-rc5' of git://git.infradead.org/users/vkoul/slave-dma: Revert "dmaengine: virt-dma: don't always free descriptor upon completion" dmaengine: mv_xor: fix big endian operation in register mode dmaengine: xgene-dma: Fix the resource map to handle overlapping dmaengine: at_xdmac: fix transfer data width in at_xdmac_prep_slave_sg() dmaengine: at_hdmac: fix residue computation dmaengine: at_xdmac: fix bug about channel configuration dmaengine: pl330: Really fix choppy sound because of wrong residue calculation dmaengine: pl330: Fix overflow when reporting residue in memcpy
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull irq fixlets from Thomas Gleixner: "Just two updates to the maintainers file" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: MAINTAINERS: Appoint Jiang and Marc as irqdomain maintainers MAINTAINERS: Appoint Marc Zyngier as irqchips co-maintainer
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fixes from Ingo Molnar: "Fallout from the recent NMI fixes: make x86 LDT handling more robust. Also some EFI fixes" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ldt: Make modify_ldt synchronous x86/xen: Probe target addresses in set_aliased_prot() before the hypercall x86/irq: Use the caller provided polarity setting in mp_check_pin_attr() efi: Check for NULL efi kernel parameters x86/efi: Use all 64 bit of efi_memmap in setup_e820()
-
- 01 8月, 2015 12 次提交
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking fixes from David Miller: 1) Must teardown SR-IOV before unregistering netdev in igb driver, from Alex Williamson. 2) Fix ipv6 route unreachable crash in IPVS, from Alex Gartrell. 3) Default route selection in ipv4 should take the prefix length, table ID, and TOS into account, from Julian Anastasov. 4) sch_plug must have a reset method in order to purge all buffered packets when the qdisc is reset, likewise for sch_choke, from WANG Cong. 5) Fix deadlock and races in slave_changelink/br_setport in bridging. From Nikolay Aleksandrov. 6) mlx4 bug fixes (wrong index in port even propagation to VFs, overzealous BUG_ON assertion, etc.) from Ido Shamay, Jack Morgenstein, and Or Gerlitz. 7) Turn off klog message about SCTP userspace interface compat that makes no sense at all, from Daniel Borkmann. 8) Fix unbounded restarts of inet frag eviction process, causing NMI watchdog soft lockup messages, from Florian Westphal. 9) Suspend/resume fixes for r8152 from Hayes Wang. 10) Fix busy loop when MSG_WAITALL|MSG_PEEK is used in TCP recv, from Sabrina Dubroca. 11) Fix performance regression when removing a lot of routes from the ipv4 routing tables, from Alexander Duyck. 12) Fix device leak in AF_PACKET, from Lars Westerhoff. 13) AF_PACKET also has a header length comparison bug due to signedness, from Alexander Drozdov. 14) Fix bug in EBPF tail call generation on x86, from Daniel Borkmann. 15) Memory leaks, TSO stats, watchdog timeout and other fixes to thunderx driver from Sunil Goutham and Thanneeru Srinivasulu. 16) act_bpf can leak memory when replacing programs, from Daniel Borkmann. 17) WOL packet fixes in gianfar driver, from Claudiu Manoil. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (79 commits) stmmac: fix missing MODULE_LICENSE in stmmac_platform gianfar: Enable device wakeup when appropriate gianfar: Fix suspend/resume for wol magic packet gianfar: Fix warning when CONFIG_PM off act_pedit: check binding before calling tcf_hash_release() net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket net: sched: fix refcount imbalance in actions r8152: reset device when tx timeout r8152: add pre_reset and post_reset qlcnic: Fix corruption while copying act_bpf: fix memory leaks when replacing bpf programs net: thunderx: Fix for crash while BGX teardown net: thunderx: Add PCI driver shutdown routine net: thunderx: Fix crash when changing rss with mutliple traffic flows net: thunderx: Set watchdog timeout value net: thunderx: Wakeup TXQ only if CQE_TX are processed net: thunderx: Suppress alloc_pages() failure warnings net: thunderx: Fix TSO packet statistic net: thunderx: Fix memory leak when changing queue count net: thunderx: Fix RQ_DROP miscalculation ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs由 Linus Torvalds 提交于
Pull btrfs fixes from Chris Mason: "Filipe fixed up a hard to trigger ENOSPC regression from our merge window pull, and we have a few other smaller fixes" * 'for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: Btrfs: fix quick exhaustion of the system array in the superblock btrfs: its btrfs_err() instead of btrfs_error() btrfs: Avoid NULL pointer dereference of free_extent_buffer when read_tree_block() fail btrfs: Fix lockdep warning of btrfs_run_delayed_iputs()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound由 Linus Torvalds 提交于
Pull sound fixes from Takashi Iwai: "This became a relative big update as it includes the collected ASoC fixes. There are a few fixes in ASoC core side, mostly for DAPM and the new topology API. The rest are various ASoC driver-specific fixes, as well as the usual HD-audio and USB-audio quirks" * tag 'sound-4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (29 commits) ALSA: hda - Fix MacBook Pro 5,2 quirk ALSA: hda - Fix race between PM ops and HDA init/probe ALSA: usb-audio: add dB range mapping for some devices ALSA: hda - Apply a fixup to Dell Vostro 5480 ALSA: hda - Add pin quirk for the headset mic jack detection on Dell laptop ALSA: hda - Apply fixup for another Toshiba Satellite S50D ALSA: fireworks: add support for AudioFire2 quirk ALSA: hda - Fix the headset mic that will not work on Dell desktop machine ALSA: hda - fix cs4210_spdif_automute() ASoC: pcm1681: Fix setting de-emphasis sampling rate selection ASoC: ssm4567: Keep TDM_BCLKS in ssm4567_set_dai_fmt ASoC: sgtl5000: Fix up define for SGTL5000_SMALL_POP ASoC: dapm: Don't add prefix to widget stream name ASoC: rt5645: Check if codec is initialized in workqueue handler ASoC: Intel: Get correct usage_count value to load firmware ASoC: topology: Fix to add dapm mixer info ASoC: zx: spdif: Fix devm_ioremap_resource return value check ASoC: zx: i2s: Fix devm_ioremap_resource return value check ASoC: mediatek: Use platform_of_node for machine drivers ASoC: Free card DAPM context on snd_soc_instantiate_card() error path ...
-
由 Joachim Eastwood 提交于
Commit 50649ab1 ("stmmac: drop driver from stmmac platform code") was a bit overzealous in removing code and dropped the MODULE_* macro's that are still needed since stmmac_platform can be a module. Fix this by putting the macro's remvoed in 50649ab1 back. This fixes the following errors when used as a module: stmmac_platform: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint stmmac_platform: Unknown symbol devm_kmalloc (err 0) stmmac_platform: Unknown symbol stmmac_suspend (err 0) stmmac_platform: Unknown symbol platform_get_irq_byname (err 0) stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0) stmmac_platform: Unknown symbol platform_get_resource (err 0) stmmac_platform: Unknown symbol of_get_phy_mode (err 0) stmmac_platform: Unknown symbol of_property_read_u32_array (err 0) stmmac_platform: Unknown symbol of_alias_get_id (err 0) stmmac_platform: Unknown symbol stmmac_resume (err 0) stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0) Fixes: 50649ab1 ("stmmac: drop driver from stmmac platform code") Reported-by: NIgor Gnatenko <i.gnatenko.brain@gmail.com> Signed-off-by: NJoachim Eastwood <manabian@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Claudiu Manoil says: ==================== gianfar: wol magic packet fixes These changes were already validated as part of FSL SDK. Patch 2 fixes occasional wake-on magic packet failures during traffic, probably due to incorrect traffic stop/ device halt sequence and incorrect usage of txlock. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Claudiu Manoil 提交于
The wol_en flag is 0 by default anyway, and we have the following inconsistency: a MAGIC packet wol capable eth interface is registered as a wake-up source but unable to wake-up the system as wol_en is 0 (wake-on flag set to 'd'). Calling set_wakeup_enable() at netdev open is just redundant because wol_en is 0 by default. Let only ethtool call set_wakeup_enable() for now. The bflock is obviously obsoleted, its utility has been corroded over time. The bitfield flags used today in gianfar are accessed only on the init/ config path, with no real possibility of concurrency - nothing that would justify smth. like bflock. Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Claudiu Manoil 提交于
If we disable NAPI in the first place we can mask the device's interrupts (and halt it) without fearing that imask may be concurrently accessed from interrupt context, so there's no need to do local_irq_save() around gfar_halt_nodisable(). lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially buggy routines. The txlock is currently used in the driver only to manage TX congestion, it has nothing to do with halting the device. With these changes, the TX processing is stopped before gfar_halt(). Compact gfar_halt() is used instead of gfar_halt_nodisable(), as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues. gfar_start() re-enables all these blocks on resume. Enabling the magic-packet mode remains the same, note that the RX block is re-enabled just before entering sleep mode. Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal that the interrupt line must remain active during sleep in order to wake the system by magic packet (MAG) reception interrupt. (On some systems the MAG interrupt did trigger w/o this flag as well, but on others it didn't.) Without these fixes, when suspended during fair Tx traffic the interface occasionally failed to be woken up by magic packet. Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Claudiu Manoil 提交于
CC drivers/net/ethernet/freescale/gianfar.o drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs' defined but not used [-Wunused-function] static void lock_tx_qs(struct gfar_private *priv) ^ drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs' defined but not used [-Wunused-function] static void unlock_tx_qs(struct gfar_private *priv) ^ Reported-by: NScott Wood <scottwood@freescale.com> Signed-off-by: NClaudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 WANG Cong 提交于
When we share an action within a filter, the bind refcnt should increase, therefore we should not call tcf_hash_release(). Fixes: 1a29321e ("net_sched: act: Dont increment refcnt on replace") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com> Signed-off-by: NCong Wang <cwang@twopensource.com> Acked-by: NDaniel Borkmann <daniel@iogearbox.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu由 Linus Torvalds 提交于
Pull IOMMU fixes from Joerg Roedel: "These fixes are all for the AMD IOMMU driver: - A regression with HSA caused by the conversion of the driver to default domains. The fixes make sure that an HSA device can still be attached to an IOMMUv2 domain and that these domains also allow non-IOMMUv2 capable devices. - Fix iommu=pt mode which did not work because the dma_ops where set to nommu_ops, which breaks devices that can only do 32bit DMA. - Fix an issue with non-PCI devices not working, because there are no dma_ops for them. This issue was discovered recently as new AMD x86 platforms have non-PCI devices too" * tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/amd: Allow non-ATS devices in IOMMUv2 domains iommu/amd: Set global dma_ops if swiotlb is disabled iommu/amd: Use swiotlb in passthrough mode iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains iommu/amd: Use iommu core for passthrough mode iommu/amd: Use iommu_attach_group()
-
git://anongit.freedesktop.org/drm-intel由 Linus Torvalds 提交于
Pull drm intel fixes from Daniel Vetter: "I delayed my -fixes pull a bit hoping that I could include a fix for the dp mst stuff but looks a bit more nasty than that. So just 3 other regression fixes, one 4.2 other two cc: stable" * tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel: drm/i915: Declare the swizzling unknown for L-shaped configurations drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
Pull drm fixes from Dave Airlie: "This has a bunch of nouveau fixes, as Ben has been hibernating and has lots of small fixes for lots of bugs across nouveau. Radeon has one major fix for hdmi/dp audio regression that is larger than Alex would like, but seems to fix up a fair few bugs, along with some misc fixes. And a few msm fixes, one of which is also a bit large. But nothing in here seems insane or crazy for this stage, just more than I'd like" * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits) drm/msm/mdp5: release SMB (shared memory blocks) in various cases drm/msm: change to uninterruptible wait in atomic commit drm/msm: mdp4: Fix drm_framebuffer dereference crash drm/msm: fix msm_gem_prime_get_sg_table() drm/amdgpu: add new parameter to seperate map and unmap drm/amdgpu: hdp_flush is not needed for inside IB drm/amdgpu: different emit_ib for gfx and compute drm/amdgpu: information leak in amdgpu_info_ioctl() drm/amdgpu: clean up init sequence for failures drm/radeon/combios: add some validation of lvds values drm/radeon: rework audio modeset to handle non-audio hdmi features drm/radeon: rework audio detect (v4) drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h drm/nouveau/nouveau/ttm: fix tiled system memory with Maxwell drm/nouveau/kms/nv50-: guard against enabling cursor on disabled heads drm/nouveau/fbcon/g80: reduce PUSH_SPACE alloc, fire ring on accel init drm/nouveau/fbcon/gf100-: reduce RING_SPACE allocation drm/nouveau/fbcon/nv11-: correctly account for ring space usage drm/nouveau/bios: add proper support for opcode 0x59 ...
-
- 31 7月, 2015 23 次提交
-
-
由 Jun Nie 提交于
This reverts commit b9855f03. The patch break existing DMA usage case. For example, audio SOC dmaengine never release channel and cause virt-dma to cache too much memory in descriptor to exhaust system memory. Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Thomas Petazzoni 提交于
Commit 6f166312 ("dmaengine: mv_xor: add support for a38x command in descriptor mode") introduced the support for a feature that appeared in Armada 38x: specifying the operation to be performed in a per-descriptor basis rather than globally per channel. However, when doing so, it changed the function mv_chan_set_mode() to use: if (IS_ENABLED(__BIG_ENDIAN)) instead of: #if defined(__BIG_ENDIAN) While IS_ENABLED() is perfectly fine for CONFIG_* symbols, it is not for other symbols such as __BIG_ENDIAN that is provided directly by the compiler. Consequently, the commit broke support for big-endian, as the XOR_DESCRIPTOR_SWAP flag was not set in the XOR channel configuration register. The primarily visible effect was some nasty warnings and failures appearing during the self-test of the XOR unit: [ 1.197368] mv_xor d0060900.xor: error on chan 0. intr cause 0x00000082 [ 1.197393] mv_xor d0060900.xor: config 0x00008440 [ 1.197410] mv_xor d0060900.xor: activation 0x00000000 [ 1.197427] mv_xor d0060900.xor: intr cause 0x00000082 [ 1.197443] mv_xor d0060900.xor: intr mask 0x000003f7 [ 1.197460] mv_xor d0060900.xor: error cause 0x00000000 [ 1.197477] mv_xor d0060900.xor: error addr 0x00000000 [ 1.197491] ------------[ cut here ]------------ [ 1.197513] WARNING: CPU: 0 PID: 1 at ../drivers/dma/mv_xor.c:664 mv_xor_interrupt_handler+0x14c/0x170() See also: http://storage.kernelci.org/next/next-20150617/arm-mvebu_v7_defconfig+CONFIG_CPU_BIG_ENDIAN=y/lab-khilman/boot-armada-xp-openblocks-ax3-4.txtSigned-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com> Fixes: 6f166312 ("dmaengine: mv_xor: add support for a38x command in descriptor mode") Reviewed-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Rameshwar Prasad Sahu 提交于
There is an overlap in dma ring cmd csr region due to sharing of ethernet ring cmd csr region. This patch fix the resource overlapping by mapping the entire dma ring cmd csr region. Signed-off-by: NRameshwar Prasad Sahu <rsahu@apm.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Cyrille Pitchen 提交于
This patch adds the missing update of the transfer data width in at_xdmac_prep_slave_sg(). Indeed, for each item in the scatter-gather list, we check whether the transfer length is aligned with the data width provided by dmaengine_slave_config(). If so, we directly use this data width for the current part of the transfer we are preparing. Otherwise, the data width is reduced to 8 bits (1 byte). Of course, the actual number of register accesses must also be updated to match the new data width. So one chunk was missing in the original patch (see Fixes tag below): the number of register accesses was correctly set to (len >> fixed_dwidth) in mbr_ubc but the real data width was not updated in mbr_cfg. Since mbr_cfg may change for each part of the scatter-gather transfer this also explains why the original patch used the Descriptor View 2 instead of the Descriptor View 1. Let's take the example of a DMA transfer to write 8bit data into an Atmel USART with FIFOs. When FIFOs are enabled in the USART, its Transmit Holding Register (THR) works in multidata mode, that is to say that up to 4 8bit data can be written into the THR in a single 32bit access and it is still possible to write only one data with a 8bit access. To take advantage of this new feature, the DMA driver was modified to allow multiple dwidths when doing slave transfers. For instance, when the total length is 22 bytes, the USART driver splits the transfer into 2 parts: First part: 20 bytes transferred through 5 32bit writes into THR Second part: 2 bytes transferred though 2 8bit writes into THR For the second part, the data width was first set to 4_BYTES by the USART driver thanks to dmaengine_slave_config() then at_xdmac_prep_slave_sg() reduces this data width to 1_BYTE because the 2 byte length is not aligned with the original 4_BYTES data width. Since the data width is modified, the actual number of writes into THR must be set accordingly. Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com> Fixes: 6d3a7d9e ("dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers") Cc: stable@vger.kernel.org #4.0 and later Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Cyrille Pitchen 提交于
As claimed by the programmer datasheet and confirmed by the IP designer, the Block Transfer Size (BTSIZE) bitfield of the Channel x Control A Register (CTRLAx) always refers to a number of Source Width (SRC_WIDTH) transfers. Both the SRC_WIDTH and BTSIZE bitfields can be extacted from the CTRLAx register to compute the DMA residue. So the 'tx_width' field is useless and can be removed from the struct at_desc. Before this patch, atc_prep_slave_sg() was not consistent: BTSIZE was correctly initialized according to the SRC_WIDTH but 'tx_width' was always set to reg_width, which was incorrect for MEM_TO_DEV transfers. It led to bad DMA residue when 'tx_width' != SRC_WIDTH. Also the 'tx_width' field was mostly set only in the first and last descriptors. Depending on the kind of DMA transfer, this field remained uninitialized for intermediate descriptors. The accurate DMA residue was computed only when the currently processed descriptor was the first or the last of the chain. This algorithm was a little bit odd. An accurate DMA residue can always be computed using the SRC_WIDTH and BTSIZE bitfields in the CTRLAx register. Finally, the test to check whether the currently processed descriptor is the last of the chain was wrong: for cyclic transfer, last_desc->lli.dscr is NOT equal to zero, since set_desc_eol() is never called, but logically equal to first_desc->txd.phys. This bug has a side effect on the drivers/tty/serial/atmel_serial.c driver, which uses cyclic DMA transfer to receive data. Since the DMA residue was wrong each time the DMA transfer reaches the second (and last) period of the transfer, no more data were received by the USART driver till the cyclic DMA transfer loops back to the first period. Signed-off-by: NCyrille Pitchen <cyrille.pitchen@atmel.com> Acked-by: NTorsten Fleischer <torfl6749@gmail.com> Tested-by: NJirí Prchal <jiri.prchal@aksignal.cz> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Ludovic Desroches 提交于
When using descriptor view 2 or higher, we don't write the configuration into AT_XDMAC_CC register because this configuration will be fetch from the descriptor. Unfortunately, the PROT bit is not updated with this method, we have to do it manually before enabling the channel. Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: NVinod Koul <vinod.koul@intel.com>
-
由 Joerg Roedel 提交于
With the grouping of multi-function devices a non-ATS capable device might also end up in the same domain as an IOMMUv2 capable device. So handle this situation gracefully and don't consider it a bug anymore. Tested-by: NOded Gabbay <oded.gabbay@gmail.com> Signed-off-by: NJoerg Roedel <jroedel@suse.de>
-
由 Andy Lutomirski 提交于
modify_ldt() has questionable locking and does not synchronize threads. Improve it: redesign the locking and synchronize all threads' LDTs using an IPI on all modifications. This will dramatically slow down modify_ldt in multithreaded programs, but there shouldn't be any multithreaded programs that care about modify_ldt's performance in the first place. This fixes some fallout from the CVE-2015-5157 fixes. Signed-off-by: NAndy Lutomirski <luto@kernel.org> Reviewed-by: NBorislav Petkov <bp@suse.de> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: security@kernel.org <security@kernel.org> Cc: <stable@vger.kernel.org> Cc: xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/4c6978476782160600471bd865b318db34c7b628.1438291540.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
-
由 Andy Lutomirski 提交于
The update_va_mapping hypercall can fail if the VA isn't present in the guest's page tables. Under certain loads, this can result in an OOPS when the target address is in unpopulated vmap space. While we're at it, add comments to help explain what's going on. This isn't a great long-term fix. This code should probably be changed to use something like set_memory_ro. Signed-off-by: NAndy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <dvrabel@cantab.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: security@kernel.org <security@kernel.org> Cc: <stable@vger.kernel.org> Cc: xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/0b0e55b995cda11e7829f140b833ef932fcabe3a.1438291540.git.luto@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
-
由 Ingo Molnar 提交于
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent Pull EFI fixes from Matt Fleming: * Fix an EFI boot issue preventing a Parallels virtual machine from booting because the upper 32-bits of the EFI memmap pointer were being discarded in setup_e820(). (Dmitry Skorodumov) * Validate that the "efi" kernel parameter gets used with an argument, otherwise we will oops. (Ricardo Neri) Signed-off-by: NIngo Molnar <mingo@kernel.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs由 Linus Torvalds 提交于
Pull xfs fixes from Dave Chinner: "There are a couple of recently found, long standing remote attribute corruption fixes caused by log recovery getting confused after a crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to actually use the DAX fault path on read faults. Summary: - remote attribute log recovery corruption fixes - DAX page faults need to use direct mappings, not a page cache mapping" * tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: xfs: remote attributes need to be considered data xfs: remote attribute headers contain an invalid LSN xfs: call dax_fault on read page faults for DAX
-
由 Sowmini Varadhan 提交于
The newsk returned by sk_clone_lock should hold a get_net() reference if, and only if, the parent is not a kernel socket (making this similar to sk_alloc()). E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock sets up the syn_recv newsk from sk_clone_lock. When the parent (listen) socket is a kernel socket (defined in sk_alloc() as having sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt and should not hold a get_net() reference. Fixes: 26abe143 ("net: Modify sk_alloc to not reference count the netns of kernel sockets.") Acked-by: NEric Dumazet <edumazet@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Daniel Borkmann 提交于
Since commit 55334a5d ("net_sched: act: refuse to remove bound action outside"), we end up with a wrong reference count for a tc action. Test case 1: FOO="1,6 0 0 4294967295," BAR="1,6 0 0 4294967294," tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \ action bpf bytecode "$FOO" tc actions show action bpf action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe index 1 ref 1 bind 1 tc actions replace action bpf bytecode "$BAR" index 1 tc actions show action bpf action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe index 1 ref 2 bind 1 tc actions replace action bpf bytecode "$FOO" index 1 tc actions show action bpf action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe index 1 ref 3 bind 1 Test case 2: FOO="1,6 0 0 4294967295," tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok tc actions show action gact action order 0: gact action pass random type none pass val 0 index 1 ref 1 bind 1 tc actions add action drop index 1 RTNETLINK answers: File exists [...] tc actions show action gact action order 0: gact action pass random type none pass val 0 index 1 ref 2 bind 1 tc actions add action drop index 1 RTNETLINK answers: File exists [...] tc actions show action gact action order 0: gact action pass random type none pass val 0 index 1 ref 3 bind 1 What happens is that in tcf_hash_check(), we check tcf_common for a given index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've found an existing action. Now there are the following cases: 1) We do a late binding of an action. In that case, we leave the tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init() handler. This is correctly handeled. 2) We replace the given action, or we try to add one without replacing and find out that the action at a specific index already exists (thus, we go out with error in that case). In case of 2), we have to undo the reference count increase from tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to do so because of the 'tcfc_bindcnt > 0' check which bails out early with an -EPERM error. Now, while commit 55334a5d prevents 'tc actions del action ...' on an already classifier-bound action to drop the reference count (which could then become negative, wrap around etc), this restriction only accounts for invocations outside a specific action's ->init() handler. One possible solution would be to add a flag thus we possibly trigger the -EPERM ony in situations where it is indeed relevant. After the patch, above test cases have correct reference count again. Fixes: 55334a5d ("net_sched: act: refuse to remove bound action outside") Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net> Reviewed-by: NCong Wang <cwang@twopensource.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Hayes Wang says: ==================== r8152: device reset v3: For patch #2, remove cancel_delayed_work(). v2: For patch #1, remove usb_autopm_get_interface(), usb_autopm_put_interface(), and the checking of intf->condition. For patch #2, replace the original method with usb_queue_reset_device() to reset the device. v1: Although the driver works normally, we find the device may get all 0xff data when transmitting packets on certain platforms. It would break the device and no packet could be transmitted. The reset is necessary to recover the hw for this situation. ==================== Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
The device reset is necessary if the hw becomes abnormal and stops transmitting packets. Signed-off-by: NHayes Wang <hayeswang@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 hayeswang 提交于
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when calling usb_reset_device(). The two functions could reduce the time of reset when calling usb_reset_device() after probe(). Signed-off-by: NHayes Wang <hayeswang@realtek.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Takashi Iwai 提交于
MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this seems not working correctly, a fix for pin NID 0x15 is needed in addition. It's equivalent with the fixup for MacBook Air 1,1, so use this instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by: NJeffery Miller <jefferym@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Thomas Gleixner 提交于
Ben was pretty surprised that he is still listed as the maintainer and he has no objections against transferring the duty to those who rumaged in and revamped that code in the recent past. Add kernel/irq/msi.c to the affected files as it's part of the shiny new hierarchical irqdomain machinery. Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Grant Likely <grant.likely@linaro.org>
-
由 Thomas Gleixner 提交于
Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Acked-by: NJason Cooper <jason@lakedaemon.net> Cc: Marc Zyngier <marc.zyngier@arm.com>
-
由 Jiang Liu 提交于
Commit d32932d0 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces") introduced a regression which causes malfunction of interrupt lines. The reason is that the conversion of mp_check_pin_attr() missed to update the polarity selection of the interrupt pin with the caller provided setting and instead uses a stale attribute value. That in turn results in chosing the wrong interrupt flow handler. Use the caller supplied setting to configure the pin correctly which also choses the correct interrupt flow handler. This restores the original behaviour and on the affected machine/driver (Surface Pro 3, i2c controller) all IOAPIC IRQ configuration are identical to v4.1. Fixes: d32932d0 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces") Reported-and-tested-by: NMatt Fleming <matt@codeblueprint.co.uk> Reported-and-tested-by: NChen Yu <yu.c.chen@intel.com> Signed-off-by: NJiang Liu <jiang.liu@linux.intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Chen Yu <yu.c.chen@intel.com> Cc: Yinghai Lu <yinghai@kernel.org> Link: http://lkml.kernel.org/r/1438242695-23531-1-git-send-email-jiang.liu@linux.intel.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input由 Linus Torvalds 提交于
Pull input fixes from Dmitry Torokhov: "The main change is support for keyboards and touchpads found in 2015 editions of Macbooks" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Revert "Input: zforce - don't overwrite the stack" Input: bcm5974 - add support for the 2015 Macbook Pro HID: apple: Add support for the 2015 Macbook Pro Input: bcm5974 - prepare for a new trackpad generation Input: synaptics - dump ext10 capabilities as well
-
由 Ricardo Neri 提交于
Even though it is documented how to specifiy efi parameters, it is possible to cause a kernel panic due to a dereference of a NULL pointer when parsing such parameters if "efi" alone is given: PANIC: early exception 0e rip 10:ffffffff812fb361 error 0 cr2 0 [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.2.0-rc1+ #450 [ 0.000000] ffffffff81fe20a9 ffffffff81e03d50 ffffffff8184bb0f 00000000000003f8 [ 0.000000] 0000000000000000 ffffffff81e03e08 ffffffff81f371a1 64656c62616e6520 [ 0.000000] 0000000000000069 000000000000005f 0000000000000000 0000000000000000 [ 0.000000] Call Trace: [ 0.000000] [<ffffffff8184bb0f>] dump_stack+0x45/0x57 [ 0.000000] [<ffffffff81f371a1>] early_idt_handler_common+0x81/0xae [ 0.000000] [<ffffffff812fb361>] ? parse_option_str+0x11/0x90 [ 0.000000] [<ffffffff81f4dd69>] arch_parse_efi_cmdline+0x15/0x42 [ 0.000000] [<ffffffff81f376e1>] do_early_param+0x50/0x8a [ 0.000000] [<ffffffff8106b1b3>] parse_args+0x1e3/0x400 [ 0.000000] [<ffffffff81f37a43>] parse_early_options+0x24/0x28 [ 0.000000] [<ffffffff81f37691>] ? loglevel+0x31/0x31 [ 0.000000] [<ffffffff81f37a78>] parse_early_param+0x31/0x3d [ 0.000000] [<ffffffff81f3ae98>] setup_arch+0x2de/0xc08 [ 0.000000] [<ffffffff8109629a>] ? vprintk_default+0x1a/0x20 [ 0.000000] [<ffffffff81f37b20>] start_kernel+0x90/0x423 [ 0.000000] [<ffffffff81f37495>] x86_64_start_reservations+0x2a/0x2c [ 0.000000] [<ffffffff81f37582>] x86_64_start_kernel+0xeb/0xef [ 0.000000] RIP 0xffffffff81ba2efc This panic is not reproducible with "efi=" as this will result in a non-NULL zero-length string. Thus, verify that the pointer to the parameter string is not NULL. This is consistent with other parameter-parsing functions which check for NULL pointers. Signed-off-by: NRicardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Dave Young <dyoung@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
-
由 Dmitry Skorodumov 提交于
The efi_info structure stores low 32 bits of memory map in efi_memmap and high 32 bits in efi_memmap_hi. While constructing pointer in the setup_e820(), need to take into account all 64 bit of the pointer. It is because on 64bit machine the function efi_get_memory_map() may return full 64bit pointer and before the patch that pointer was truncated. The issue is triggered on Parallles virtual machine and fixed with this patch. Signed-off-by: NDmitry Skorodumov <sdmitry@parallels.com> Cc: Denis V. Lunev <den@openvz.org> Cc: <stable@vger.kernel.org> Signed-off-by: NMatt Fleming <matt.fleming@intel.com>
-
- 30 7月, 2015 2 次提交
-
-
由 Linus Torvalds 提交于
Merge tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fixes from Guenter Roeck: "Two patches headed for -stable. nct7802: Fix integer overflow seen when writing voltage limits nct7904: Rename pwm attributes to match hwmon ABI" * tag 'hwmon-for-linus-v4.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (nct7802) Fix integer overflow seen when writing voltage limits hwmon: (nct7904) Rename pwm attributes to match hwmon ABI
-
由 Chris Wilson 提交于
The old style of memory interleaving swizzled upto the end of the first even bank of memory, and then used the remainder as unswizzled on the unpaired bank - i.e. swizzling is not constant for all memory. This causes problems when we try to migrate memory and so the kernel prevents migration at all when we detect L-shaped inconsistent swizzling. However, this issue also extends to userspace who try to manually detile into memory as the swizzling for an individual page is unknown (it depends on its physical address only known to the kernel), userspace cannot correctly swizzle. Note that this is a new attempt for the previously merged one, reverted in commit d82c0ba6 Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Tue Jul 14 12:29:27 2015 +0200 Revert "drm/i915: Declare the swizzling unknown for L-shaped configurations" This is cc: stable since we need it to fix up troubles with wc cpu mmaps that userspace recently started to use widely. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91105Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: stable@vger.kernel.org [danvet: Add note about previous (failed attempt).] Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
-