Even if the null data frame is not acked by the AP, mac80211
goes into power save. This might lead to loss of frames
from the AP.
Prevent this by restarting dynamic_ps_timer when ack is not
received for null data frames.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The current mac80211 implementation enables power save if there
is no Tx traffic for a specific timeout. Hence, PS is triggered
even if there is a continuous Rx only traffic(like UDP) going on.
This makes the drivers to wait on the tim bit in the next beacon
to awake which leads to redundant sleep-wake cycles.
Fix this by restarting the dynamic ps timer on receiving every
data packet.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
CC: stable@kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rate_control_alloc is not used by anything outside of
ieee80211_init_rate_ctrl_alg.  Both are in rate.c; there's no reason to make
rate_control_alloc visible outside of it.
Signed-off-by: NAndres Salomon <dilinger@collabora.co.uk>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a WARN_ON which is triggered
by Poland's country code.

ath: EEPROM regdomain: 0x8268
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x37
ath: Country alpha2 being used: PL
ath: Regpair used: 0x37
  -----------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/regd.c:155 ath_regd_init+0x30b
Pid: 12661, comm: firmware/carl91 2.6.33-rc5-wl #18
Call Trace:
 [<>] ? warn_slowpath_common+0x76/0x8c
 [<>] ? ar9170_reg_notifier+0x0/0x2d [carl9170usb]
 [<>] ? ath_regd_init+0x30b/0x377 [ath]
 [<>] ? ar9170_register+0x3b3/0x3ca [carl9170usb]
[...]
---[ end trace ]---

Note: Poland is just an example. But it is very likely
that more country codes are affected.

Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() driver operation is not currently used anywhere in mac80211
and there are no plans to use it in the not-so-near future. So it can go
without anyone missing it.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

p54 uses struct ieee80211_tx_queue_stats also internally, so create a new
identical struct p54_tx_queue_stats which the driver can use.

Compile-tested only.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Tested-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Stefano Brivio <stefano.brivio@polimi.it>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Because ar9170 uses ieee80211_tx_queue_stats internally, create a new
identical struct ar9170_tx_queue_stats which the driver can use.

Compile-tested only.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Tested-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

mwl8k used struct ieee80211_tx_queue_stats internally to track the queue
lenght. Replace struct ieee80211_tx_queue_stats with a simple len field
in struct mwl8k_tx_queue. Limit and count fields seemed to be unused.

Compile-tested only.

Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

get_tx_stats() will be removed from mac80211.

Compile-tested only.

Cc: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When userspace requests a deauth while the
authentication work is pending in the auth
(not probe) state, we do not properly abort
the work and then things get confused.

Fix that and also improve the checks here
to include the correct virtual interface,
just in case two virtual interfaces would
ever try to connect to the same BSS.

Also fix a bug -- need to use list_del_rcu
instead of just list_del to free a work
item.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When running directed active scans we currently end up sending both the SSID
probe requests and an additional broadcast one.
This is due to the fact that we always leave the probe request template SSID IE
length to 0. Instead we should set it to the first SSID to scan, and fill the
direct_scan array with the remaining SSIDs to scan for. This way we only send
what we've been asked to: a broadcast probe request when no directed scan is
requested, and directed probe requests otherwise.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Existing iwl6050_ops->iwl6050_hcmd_utils structure had no pointers to chain
noise functions (gain_computation and chain_noise_reset).  As it turns out,
by adding chain_noise_scale (see related patch), there is no need for separate
chain noise function, so simply use iwl6000_ops->iwl5000_hcmd_utils, and
remove those for 6050.
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

6x50 device requires a different scaling factor for Rx gain values sent to
device via PHY_CALIBRATION_CMD (CHAIN_NOISE_GAIN_CMD).  Rather than create
a new iwlXXXX_gain_computation() function, add new chain_noise_scale member
to struct iwl_cfg, and keep using iwl5000_gain_computation().
Signed-off-by: NBen Cahill <ben.m.cahill@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In AP mode, the only mode where the parameter
is supposed to be valid, we never assign it!
Fix that to allow drivers to avoid parsing
the TIM IE for the value.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This file helps debugging HT channels since it displays if we are on
ht20 or ht40+/ht40-
Signed-off-by: NBenoit Papillault <benoit.papillault@free.fr>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Retrying commands seldomly works, most often the firmware is in a
weird state anyway and needs the device to reset. So it's better
to report the broken state back to user-space.

Also rename command_timer_fn() into lbs_cmd_timeout_handler(),
which better reflect it's usage.
Signed-off-by: NHolger Schurig <holgerschurig@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 uses unit units of 32 usec with txop but wl1251_acx_ac_cfg()
expects it to be usecs. This fortunately didn't cause any severe problems,
only that firmware was using incorrect WMM settings.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

libertas/if_spi.c needs to #include linux/semaphore.h to fix build errors:

drivers/net/wireless/libertas/if_spi.c:59: error: field 'spi_ready' has incomplete type
drivers/net/wireless/libertas/if_spi.c:60: error: field 'spi_thread_terminated' has incomplete type
drivers/net/wireless/libertas/if_spi.c:785: error: implicit declaration of function 'down_interruptible'
drivers/net/wireless/libertas/if_spi.c:787: error: implicit declaration of function 'up'
drivers/net/wireless/libertas/if_spi.c:834: error: implicit declaration of function 'down'
drivers/net/wireless/libertas/if_spi.c:943: error: implicit declaration of function 'sema_init'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Explicitely enable shared interrupt 2 for any core that didn't get a dedicated IRQ
anymore (fallthrough case) and for EXTIF cores to make gpio interrupts work.
Also remove a bogus comment.
Signed-off-by: NJochen Friedrich <jochen@scram.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If b43 or b43legacy are deauthenticated or disconnected, there is a
possibility that a reconnection is tried with the queues stopped in
mac80211. To prevent this, start the queues before setting
STAT_INITIALIZED.

In b43, a similar change has been in place (twice) in the
wireless_core_init() routine. Remove the duplicate and add similar
code to b43legacy.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>   [2.6.32]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When there is a need to restart/reconfig hw, tear down all the
aggregation queues and let the mac80211 and driver get in-sync to have
the opportunity to re-establish the aggregation queues again.

Need to wait until driver re-establish all the station information before tear
down the aggregation queues, driver(at least iwlwifi driver) will reject the
stop aggregation queue request if station is not ready. But also need to make
sure the aggregation queues are tear down before waking up the queues, so
mac80211 will not sending frames with aggregation bit set.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.

Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

beacons configuration SHOULD be done only if the STA is associated.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many drivers would like to sleep during station
addition and removal, and currently have a high
complexity there from not being able to.

This introduces two new callbacks sta_add() and
sta_remove() that drivers can implement instead
of using sta_notify() and that can sleep, and
the new sta_add() callback is also allowed to
fail.

The reason we didn't do this previously is that
the IBSS code wants to insert stations from the
RX path, which is a tasklet, so cannot sleep.
This patch will keep the station allocation in
that path, but moves adding the station to the
driver out of line. Since the addition can now
fail, we can have IBSS peer structs the driver
rejected -- in that case we still talk to the
station but never tell the driver about it in
the control.sta pointer. If there will ever be
a driver that has a low limit on the number of
stations and that cannot talk to any stations
that are not known to it, we need to do come up
with a new strategy of handling larger IBSSs,
maybe quicker expiry or rejecting peers.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can now easily determine whether we already
have probe response information for the BSS we
are asked to connect to, in which case there's
little point in probing the BSS again.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upstream radiotap has adopted the namespace
proposal David Young made and I then took care
of, for which I had adapted the radiotap parser
as a library outside the kernel. This brings
the in-kernel parser up to speed.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For debugging hardware scan trigger/complete
functionality, it was useful to have code in
hwsim that pretends to do a hardware scan.

This code could be extended to actually do the
scan, but for now it was sufficient for me to
only pretend. Since hwsim was written to ease
debugging, it only makes sense to add it to it
permanently.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	net/mac80211/scan.c