Make sure the return value is set in all cases

>From 9b38a5c9878b5e4be2899ae291c4524f5f5fc218 Mon Sep 17 00:00:00 2001
Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

removes obsolete comments. updates firmware versions. firmware vendor request simplified.
Signed-off-by: NDean Anderson <linux-dev@sensoray.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Removed the use of 'card_type' from the tuner configuration structure, and
replaced it with separate parameters to set board-specific configuration.
Signed-off-by: NIstvan Varga <istvan_v@mailbox.hu>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver.  I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: NDavide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.

The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)

The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.

This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.

This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NJohannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Petter Selasky <hselasky@c2i.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.
Signed-off-by: NNewson Edouard <newsondev@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

list_first_entry() always returns non-null here.  I think the intent was
to test whether there were any entries in the used list.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:

EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

PCTV Systems nanoStick T2 290e => PCTV nanoStick T2 290e
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).
Signed-off-by: NJean-François Moine <moinejf@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2.

The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: NSimon Arlott <simon@fire.lp0.eu>
Tested-by: NSimon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This reverts commit e38030f3.

MSI flat-out doesn't work right on cx2388x devices yet. There are now
multiple reports of cards that hard-lock systems when MSI is enabled,
including my own HVR-1250 when trying to use its built-in IR receiver.
Disable MSI and it works just fine. Similar for another user's HVR-1270.
Issues have also been reported with the HVR-1850 when MSI is enabled,
and the 1850 behavior sounds similar to an as-yet-undiagnosed issue I've
seen with an 1800.

CC: stable@kernel.org
CC: Steven Toth <stoth@kernellabs.com>
CC: Kusanagi Kouichi <slash@ac.auone-net.jp>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NAndy Walls <awalls@md.metrocast.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The vt->type field determines how the msp3400 should fill in the
tuner data, not whether the msp3400 is in radio mode or not.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The tuner core should not silently change the type field in g_tuner and
g_frequency. If the tuner is in a different mode than the one that was
requested, then just fill in what you can and don't attempt to read afc,
signal or rxsubchans values.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The driver shouldn't override vt->type, and the tuner name should be
based on vt->type as well.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Drivers must be able to rely on s_power to power up subdevices.

Note that at this moment no driver attempts to power up tuners. This probably
isn't surprising since s_power(1) was never implemented in tuner-core.c until
now.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prohibit attempts to change the tuner to a type that is different
from the device node the ioctl is called from. I.e. the type must
be RADIO for a radio node and ANALOG_TV for a video/vbi node.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Get rid of a number of unnecessary tuner_dbg messages by simplifying
the std fixup function.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The tuner ops g_frequency, g_tuner and s_tuner require that the tuner type
field is filled in. Document this.

The tuner-core doc is based on a patch from Mauro Carvalho Chehab <mchehab@redhat.com>.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix typo: g_tuner should have been s_tuner.

Tested with a bttv card.

Cc: stable@kernel.org
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The tuner-core subdev requires that the type field of v4l2_tuner is
filled in correctly. This is done in v4l2-ioctl.c, but pvrusb2 doesn't
use that yet, so we have to do it manually based on whether the current
input is radio or not.

Tested with my pvrusb2.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NMike Isely <isely@pobox.com>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The subdevs are supposed to receive a valid tuner type for the g_frequency
and g/s_tuner subdev ops. Some drivers do this, others don't. So prefill
this in v4l2-ioctl.c based on whether the device node from which this is
called is a radio node or not.

The spec does not require applications to fill in the type, and if they
leave it at 0 then the 'check_mode' call in tuner-core.c will return
an error and the ioctl does nothing.

Cc: stable@kernel.org
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

set_mode is called with t->type, which is the tuner type. Instead, use
t->mode which is the actual tuner mode (i.e. radio vs tv).

Cc: stable@kernel.org
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Both s_std and s_tuner are broken because set_mode_freq is called before the
new std (for s_std) and audmode (for s_tuner) are set.

This patch splits set_mode_freq in a set_mode and a set_freq and in s_std/s_tuner
first calls set_mode, and if that returns 0 (i.e. the mode is supported)
then they set t->std/t->audmode and call set_freq.

This fixes a bug where changing std or audmode would actually change it to
the previous value.

Discovered while testing analog TV standards for cx18 with a tda18271 tuner.

Cc: stable@kernel.org
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The comment says "wait 15ms", but the code says jiffies_to_msecs(15)
instead of msecs_to_jiffies(15). Fix that. Tested, works fine with both
rc5 and rc6 decode, in-kernel and via lirc userspace, with an HVR-1150.
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

mx1_camera_add_device() can return an uninitialized value of ret.
Signed-off-by: NAndre Bartke <andre.bartke@gmail.com>
[g.liakhovetski@gmx.de: modified the fix to remove "ret" completely]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The usecase where, user allocates small size of buffer
through bootargs (video1_bufsize/video2_bufsize) and later from application
tries to set the format which requires larger buffer size, driver doesn't
check for insufficient buffer size and allows application to map extra buffer.
This leads to kernel crash, when user application tries to access memory
beyond the allocation size.

Added check in both mmap and reqbuf call back function,
and return error if the size of the buffer allocated by user through
bootargs is less than the S_FMT size.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

With addition of media-controller framework, now we have various
device nodes (/dev/videoX) getting created, so hardcoding
minor number in video_register_device() is not recommended.

So let V4L2 framework choose free minor number for the device.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The omap_vout_new_crop() function has possible bug, uses uninitialized
variable "crop.width/height" which is actually output of the function.
Instead we should be using "try_crop.width/height" to calculate the
resizer value.
Signed-off-by: NVladimir Pantelic <vladoman@gmail.com>
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When failing to start the camera we should disable the queue again, to
rollback into the same initial state. Otherwise re-trying will always
hit -EBUSY
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When freeing memory for the video buffers also remove them from the
irq & main queues.

This fixes an oops when doing the following:

open ("/dev/video", ..)
VIDIOC_REQBUFS
VIDIOC_QBUF
VIDIOC_REQBUFS
close ()

As the second VIDIOC_REQBUFS will cause the list entries of the buffers
to be cleared while they still hang around on the main and irc queues
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If a streaming interface has no supported format, the driver won't
create a video device for the associated terminal. Fix an oops by
ignoring that terminal when creating links between entities.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>