irqs.h:
    * rename IRQ_LOCOMO_SPI_OVRN to IRQ_LOCOMO_SPI_REND
locomo.h:
    * add some definition for locomo spi controller
    * correct some errors
locomo.c:
    * correct some errors
    * add set_type for locomo gpio irq chip
Signed-off-by: NThomas Kunze <thommycheck@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Each time a pxa type cpu went in suspend, a portion of
kmalloc memory was corrupted.
The issue was an incorrect length allocation introduced by
the commit 711be5cc for
the save registers array (=> overflow).
Signed-off-by: NRobert Jarzmik <rjarzmik@free.fr>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes some two minor clk issues.

The first is a comparison where a byte will probably wrap around to 0 instead of being saturated to 255, shouldn't be triggered very often but need fixing.

The second is an attempt by the driver to adjust MCLK down to the maximum frequency according to the spec, so we don't accidentally overclock the PL18x block. None of the mach-{versatile|integrator|lh7a40x} that use it in-tree seem to have a problem with this (all are well below 100MHz, typically 33MHz), but some day there will be a problem.

This is not applied on top of the earlier mmci patch for race condition but rather a clean 2.6.25, but I guess it applies without major protests anyway.
Signed-off-by: NLinus Walleij <triad@df.lth.se>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Change gpio_direction_output to gpio_direction_input in
ep93xx_gpio_irq_type. Fixes broken gpio interrupts.
Signed-off-by: NRyan Mallon <ryan@bluewatersys.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

* git://git.infradead.org/battery-2.6:
  PMU battery: filenames in sysfs with spaces
  pda_power: add init and exit function callbacks

* git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-inttypes: (24 commits)
  Make constants in kernel/timeconst.h fixed 64 bits
  types: add C99-style constructors to <asm-generic/int-*.h>
  xtensa: types: use <asm-generic/int-*.h> for the xtensa architecture
  x86: types: use <asm-generic/int-*.h> for the x86 architecture
  v850: types: use <asm-generic/int-*.h> for the v850 architecture
  sparc64: types: use <asm-generic/int-*.h> for the sparc64 architecture
  sparc: types: use <asm-generic/int-*.h> for the sparc architecture
  sh: types: use <asm-generic/int-*.h> for the sh architecture
  s390: types: use <asm-generic/int-*.h> for the s390 architecture
  powerpc: types: use <asm-generic/int-*.h> for the powerpc architecture
  parisc: types: use <asm-generic/int-*.h> for the parisc architecture
  mn10300: types: use <asm-generic/int-*.h> for the mn10300 architecture
  mips: types: use <asm-generic/int-*.h> for the mips architecture
  m68k: types: use <asm-generic/int-*.h> for the m68k architecture
  m32r: types: use <asm-generic/int-*.h> for the m32r architecture
  ia64: types: use <asm-generic/int-*.h> for the ia64 architecture
  h8300: types: use <asm-generic/int-*.h> for the h8300 architecture
  frv: types: use <asm-generic/int-*.h> for the frv architecture
  cris: types: use <asm-generic/int-*.h> for the cris architecture
  blackfin: types: use <asm-generic/int-*.h> for the blackfin architecture
  ...

Many thanks to Martin for his years of hosting.  The pci list has moved to
vger, along with what seems like the rest of the major Linux mailing lists.
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  slub: #ifdef simplification
  slabinfo: Support printout of the number of fallbacks
  slub: Whitespace cleanup and use of strict_strtoul

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
  rose: Wrong list_lock argument in rose_node seqops
  netns: Fix reassembly timer to use the right namespace
  netns: Fix device renaming for sysfs
  bnx2: Update version to 1.7.5.
  bnx2: Update RV2P firmware for 5709.
  bnx2: Zero out context memory for 5709.
  bnx2: Fix register test on 5709.
  bnx2: Fix remote PHY initial link state.
  bnx2: Refine remote PHY locking.
  bridge: forwarding table information for >256 devices
  tg3: Update version to 3.92
  tg3: Add link state reporting to UMP firmware
  tg3: Fix ethtool loopback test for 5761 BX devices
  tg3: Fix 5761 NVRAM sizes
  tg3: Use constant 500KHz MI clock on adapters with a CPMU
  hci_usb.h: fix hard-to-trigger race
  dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
  net: remove NR_CPUS arrays in net/core/dev.c
  net: use get/put_unaligned_* helpers
  bluetooth: use get/put_unaligned_* helpers
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc32: Delete prom_stdin and prom_stdout.
  sparc32: More memory probing consolidation.
  sparc32: Kill totally unused memory information tables.
  sparc64: Fix syscall restart, for real...
  serial: Fix sparc driver name strings.
  sparc64: Stop creating dummy root PCI host controller devices.

* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
  [POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
  [POWERPC] PS3: Update ps3_defconfig
  [POWERPC] PS3: Remove unsupported wakeup sources
  [POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
  [POWERPC] PS3: Add time include to lpm
  [POWERPC] Fix slb.c compile warnings
  [POWERPC] Xilinx: Fix compile warnings
  [POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
  [RAPIDIO] fix current kernel-doc notation
  [POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
  Fix a potential issue in mpc52xx uart driver
  [POWERPC] mpc5200: Allow for fixed speed MII configurations
  [POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board

In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: NBernard Pidoux <f6bvp@amsat.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This trivial fix retrieves the network namespace from frag queue
and use it to get the network device in the right namespace.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.

The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.

This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.

The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.

This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NBenjamin Thery <benjamin.thery@bull.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new RV2P firmware fixes 2 issues:

1. The jumbo rx buffer page size is now configurable and set to the
   proper PAGE_SIZE.  Before, it was assumed to be always 4K.

2. Driver sometimes would crash when receiving jumbo packets mixed
   with firmware management packets.  This was caused by the old
   firmware DMA'ing to the wrong address.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should zero out the context memory for 5709 before each reset.  When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some remote PHY blade systems, the driver receives no initial link
interrupt.  As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.

With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls.  This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:

   brctl showmacs

The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version number to 3.92.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port".  This feature is implemented in firmware
and is largely transparent to the driver, except...

It turns out that the UMP firmware needs to know the current status
of the link.  Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.

This patch implements the new handshake with the UMP firmware.  Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully.  This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 5761 NVRAM sizes assigned to the nvram_size member are half as big
as they should be.  This patch corrects the NVRAM sizes and replaces
the hardcoded constants with preprocessor constants for readability.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MI clock is not configured correctly on adapters with the CPMU
present.  The tg3 driver has code which statically sets the MI clock to
be a fraction of the speed at which the core clock is running.
However, the CPMU can change the adapter's core clock frequency based
on operating conditions.  Consequently, the MI will run slow when the
core's clock has been slowed down.

There is a new 500KHz constant frequency clock available on adapters
with a CPMU.  This patch removes the static core clock scaling and
configures the MI clock to use this new 500KHz clock instead.

Running the MI clock at slower speeds will not directly result in data
corruption, but it does challenge the PHY read and write routine timeouts.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If someone tries to _urb_unlink while _urb_queue_head is running, he'll see
_urb->queue == NULL and fail to do any locking.  Prevent that from happening
by strategically placed barriers.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Makes the intention of the nested min/max clear.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the fixed size channels[NR_CPUS] array in net/core/dev.c and
dynamically allocate array based on nr_cpu_ids.
Signed-off-by: NMike Travis <travis@sgi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By changing drivers/power/pmu_battery.c I now have '_' instead of
' ' (spaces) in /sys:

/sys/devices/platform/pmu-battery.0/power_supply/PMU_battery_0
/sys/class/power_supply/PMU_battery_0

I'm still not sure if some userspace tool out there uses the old paths and
will break now.
Signed-off-by: NChristian Kujau <lists@nerdbynature.de>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

This adds init/exit function callbacks to pda_power, to
provide a place where the platform code can request/free
GPIOs that it wants to use in the is_ac_online, is_usb_online
and set_charge functions.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: NAnton Vorontsov <cbouatmailru@gmail.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

WARN_ON_ONCE() gives a stack trace including the full module list.
Having this in the kernel dump for the timeout case in the
generic netdev watchdog will help us see quicker which driver
is involved. It also allows us to collect statistics 
and patterns in terms of which drivers have this event occuring.

Suggested by Andrew Morton
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One finds all kinds of crazy things with some shell pipelining.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Force constants in kernel/timeconst.h (except shift counts) to be 64 bits,
using U64_C() constructor macros, and eliminate constants that cannot
be represented at all in 64 bits.  This avoids warnings with some gcc
versions.

Drop generating 64-bit constants, since we have no real hope of
getting a full set (operation on 64-bit values requires a 128-bit
intermediate result, which gcc only supports on 64-bit platforms, and
only with libgcc support on some.)  Note that the use of these
constants does not depend on if we are on a 32- or 64-bit architecture.

This resolves Bugzilla 10153.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

Add C99-style constructor macros for fixed types to
<asm-generic/int-*.h>.  Since Linux uses names like "u64" instead of
"uint64_t", the constructor macros are called U64_C() instead of
UINT64_C() and so forth.

These macros allow specific sizes to be specified as
U64_C(0x123456789abcdef), without gcc issuing warnings as it will if
one writes (u64)0x123456789abcdef.

When used from assembly, these macros pass their argument unchanged.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>

This modifies <asm-xtensa/types.h> to use the <asm-generic/int-*.h>
generic include files.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Cc: Chris Zankel <chris@zankel.net>