Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

defines/modifies data structures, function prototypes and changes to the
driver rendering it capable of handling <n> tx/rx queues
Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NMallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: NGanesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: NJohn Ronciak <john.ronciak@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds support for MSI/MSI-X feature to the driver.  It is
a runtime parameter(for now, loadable parameter).  Default is INTA.

Patch has been tested on IA64 platform with Xframe II adapter,
both of which support MSI-X feature.  An improvement of about 7%
in throughput(both Tx and Rx) was observed and a reduction by 7%
in CPU utilization during Tx test.
Signed-off-by: NRavinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix nocast sparse warnings in sungen:
drivers/net/sungem.h:1040:45: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix implicit nocast warnings in ns83820 code, including __nocast:
drivers/net/ns83820.c:603:46: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix implicit nocast warnings in ieee80211 code, including __nocast:
net/ieee80211/ieee80211_tx.c:215:9: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Unfortunately, [your patch] might address the crash but doesn't address
the real problem. It turns out that the problem is one of padding
(the firmware cksum engine works only on 32-bit chunks, yuck), so
the special casing for length == 1 wasn't sufficient anyway.

This patch addresses the issue, as well the other issue of i386 +
CONFIG_HIGHMEM being broken. It is pretty much the same workaround
that Adaptec themselves used in their Windows driver. I have yet to
check if it fixes the problem when the skb is non-linear, but this
patch _will_ solve the problem for 99% of the users out there (those
not using sendfile).
Signed-off-by: NIon Badulescu <ionut@badula.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch changes pocket and parallel adaptors to depend on PARPORT
instead of ISA in order to get the option in newer SuperIO based systems.
Signed-off-by: NGrant Coady <gcoady@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

This patch adds support to the ibm_emac driver for platform-specific
unsupported PHY features.

The patch attempts to determine the highest speed and duplex when
autonegotiation is unsupported.
Signed-off-by: NWade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The patch below is necessary to allow my Digital DS21143 Tulip rev 48
ethernet interface to work in a 10Mbit Half Duplex network.  Without
it, the driver keeps retrying other modes in an endless loop.  It seems
like someone already had the same problem with a rev 65 board :)
Signed-off-by: NPhilippe De Muyter <phdm@macqel.be>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

David S. Miller <davem@davemloft.net> wrote:
>I think removing support for older ifenslave binaries is
>the least painful solution to this problem.

	This patch removes backwards compatibility for old ifenslave
binaries (ifenslave prior to verison 1.0.0).

	I did not similarly modify ifenslave itself; with sysfs on the
horizon, I don't see that as being worthwhile.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

	This patch introduces new feature in qeth:
	qeth enhancement provides the device driver support for
        the Communication Controller for Linux on System z9 and zSeries
        (CCL), which is software that enables running the Network Control
        Program (NCP) on a zSeries machine. The OSA CDLC support is based
        on a new IBM mainframe CHPID type called Open Systems Adaper for
        NCP (OSN). In case of OSN qeth communicates with the type-OSN
        OSA-card on one hand, and with the CCL-kernel-component Network
        Device Handler (NDH) on the other.
Signed-off-by: NFrank Pavlic <pavlic@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

From: Peter Tiedemann <ptiedem@de.ibm.com>
From: Frank Pavlic <pavlic@de.ibm.com>
	minor qeth fixes:
	- free old skb in qeth_realloc_headroom after duplicating skb
	- disable IPV6 support for Hipersockets devices
	- call ccw_device_set_offline on every channel regardless
	  of the return value of the prior ccw_device_set_offline calls
	- allocate qdio structures in DMA-area
	- schedule recovery of appropriate card
	  when cable has been inserted again.
	- add missing initialization of card->lock
	- write sequence number in skb->cb for SNA protocol which
	  requires strictly serialized packets.
Signed-off-by: NFrank Pavlic <pavlic@de.ibm.com>

diffstat:
 qeth.h      |    2 ++
 qeth_main.c |   37 +++++++++++++++++--------------------
 2 files changed, 19 insertions(+), 20 deletions(-)
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The smc91c92_cs multicast does not work
if the count of multicast address is 1.

Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix implicit nocast warnings in ieee80211 code:
net/ieee80211/ieee80211_tx.c:215:9: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Fix implicit nocast warnings in ns83820 code:
drivers/net/ns83820.c:603:46: warning: implicit cast to nocast type
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Unregister all netdevs before freeing local data. I was unable to
trigger any crashes without this change when running busy loops for
driver operations when ejecting a Prism2 PC Card. Anyway, should there
be a race condition with this, better make it less likely to happen by
unregistering the netdevs first.
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

local->hw_priv was being freed and set to NULL just before calling
prism2_free_local_data(). However, this may expose a race condition in
which something ends up trying to use hw_priv during shutdown. I
haven't noticed this happening, but better be safe than sorry, so
let's postpone hw_priv freeing to happen only after
prism2_free_local_data() has returned.
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

The debug version of I/O functions in hostap_pci had not survived the
change to start using hw_priv pointer, so let's fix them to actually
define the local hw_priv variable.
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Host AP driver used hardware model specific dev_open/close handlers
that were called on dev_open/close if the hardware driver had
registered the handler. These were only used for hostap_cs and only
for tracking whether any of the netdevs were UP. This information is
already available from local->num_dev_open, so there is not need for
the special open/close handler.

Let's get rid of these handlers. In addition to cleaning up the code,
this fixes a module refcounting issue for hostap_cs where ejecting the
card while any of the netdevs were open did not decrement refcount
properly.
Signed-off-by: NJouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Skge driver was bringing link up/down when changing mac
address.  This doesn't work in the bonding environment, and is
more effort than needed.

Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5271Signed-off-by: NStephen Hemminger <shemminger@osdl.org>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not a good idea to be smurf'able by default.
The few people who need this can turn it on.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gets rid of a bogus __in_dev_put() in pktgen.c.  This was
spotted by Suzanne Wood.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.

1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().

There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition.  I've marked it as such so that we remember to fix it.

This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a patch from Mitsuru KANDA <mk@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-Off-By: NYan Zheng <yanzheng@21cn.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Meelis Roos <mroos@linux.ee> wrote:
> RK> My firewall setup relies on proxyarp working.  However, with 2.6.14-rc3,
> RK> it appears to be completely broken.  The firewall is 212.18.232.186,
> 
> Same here with some kernel between 14-rc2 and 14-rc3 - no reposnse to
> ARP on a proxyarp gateway. Sorry, no exact revison and no more debugging
> yet since it'a a production gateway.

The breakage is caused by the change to use the CB area for flagging
whether a packet has been queued due to proxy_delay.  This area gets
cleared every time arp_rcv gets called.  Unfortunately packets delayed
due to proxy_delay also go through arp_rcv when they are reprocessed.

In fact, I can't think of a reason why delayed proxy packets should go
through netfilter again at all.  So the easiest solution is to bypass
that and go straight to arp_process.

This is essentially what would've happened before netfilter support
was added to ARP.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> 
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During the build for ARM machine type "fortunet", this error occurred:

  CC      net/sysctl_net.o
net/sysctl_net.c:36: error: 'core_table' undeclared here (not in a function)

It appears that the following configuration settings cause this error
due to a missing include:
CONFIG_SYSCTL=y
CONFIG_NET=y
# CONFIG_INET is not set

core_table appears to be declared in net/sock.h.  if CONFIG_INET were
defined, net/sock.h would have been included via:
  sysctl_net.c -> net/ip.h -> linux/ip.h -> net/sock.h

so include it directly.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Arnaldo and I agreed it could be applied now, because I have other
pending patches depending on this one (Thank you Arnaldo)

(The other important patch moves skc_refcnt in a separate cache line,
so that the SMP/NUMA performance doesnt suffer from cache line ping pongs)

1) First some performance data :
--------------------------------

tcp_v4_rcv() wastes a *lot* of time in __inet_lookup_established()

The most time critical code is :

sk_for_each(sk, node, &head->chain) {
     if (INET_MATCH(sk, acookie, saddr, daddr, ports, dif))
         goto hit; /* You sunk my battleship! */
}

The sk_for_each() does use prefetch() hints but only the begining of
"struct sock" is prefetched.

As INET_MATCH first comparison uses inet_sk(__sk)->daddr, wich is far
away from the begining of "struct sock", it has to bring into CPU
cache cold cache line. Each iteration has to use at least 2 cache
lines.

This can be problematic if some chains are very long.

2) The goal
-----------

The idea I had is to change things so that INET_MATCH() may return
FALSE in 99% of cases only using the data already in the CPU cache,
using one cache line per iteration.

3) Description of the patch
---------------------------

Adds a new 'unsigned int skc_hash' field in 'struct sock_common',
filling a 32 bits hole on 64 bits platform.

struct sock_common {
	unsigned short		skc_family;
	volatile unsigned char	skc_state;
	unsigned char		skc_reuse;
	int			skc_bound_dev_if;
	struct hlist_node	skc_node;
	struct hlist_node	skc_bind_node;
	atomic_t		skc_refcnt;
+	unsigned int		skc_hash;
	struct proto		*skc_prot;
};

Store in this 32 bits field the full hash, not masked by (ehash_size -
1) Using this full hash as the first comparison done in INET_MATCH
permits us immediatly skip the element without touching a second cache
line in case of a miss.

Suppress the sk_hashent/tw_hashent fields since skc_hash (aliased to
sk_hash and tw_hash) already contains the slot number if we mask with
(ehash_size - 1)

File include/net/inet_hashtables.h

64 bits platforms :
#define INET_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
     (((__sk)->sk_hash == (__hash))
     ((*((__u64 *)&(inet_sk(__sk)->daddr)))== (__cookie))   &&  \
     ((*((__u32 *)&(inet_sk(__sk)->dport))) == (__ports))   &&  \
     (!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))

32bits platforms:
#define TCP_IPV4_MATCH(__sk, __hash, __cookie, __saddr, __daddr, __ports, __dif)\
     (((__sk)->sk_hash == (__hash))                 &&  \
     (inet_sk(__sk)->daddr          == (__saddr))   &&  \
     (inet_sk(__sk)->rcv_saddr      == (__daddr))   &&  \
     (!((__sk)->sk_bound_dev_if) || ((__sk)->sk_bound_dev_if == (__dif))))


- Adds a prefetch(head->chain.first) in 
__inet_lookup_established()/__tcp_v4_check_established() and 
__inet6_lookup_established()/__tcp_v6_check_established() and 
__dccp_v4_check_established() to bring into cache the first element of the 
list, before the {read|write}_lock(&head->lock);
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Acked-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.

PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I've found the problem in general.  It affects any 64-bit
architecture.  The problem occurs when you change the system time.

Suppose that when you boot your system clock is forward by a day.
This gets recorded down in skb_tv_base.  You then wind the clock back
by a day.  From that point onwards the offset will be negative which
essentially overflows the 32-bit variables they're stored in.

In fact, why don't we just store the real time stamp in those 32-bit
variables? After all, we're not going to overflow for quite a while
yet.

When we do overflow, we'll need a better solution of course.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2.6.14-rc2 does not assign cpus to proper nodeids on our em64t numa boxen.
Our boxes use acpi srat for parsing the numa information.

srat_detect_node() used phys_proc_id[] to get to the cpu's local apic id,
but phys_proc_id[] represents the cpu<->initial_apic_id mapping.  The
following patch fixes this problem.  Now apicid_to_node[] is properly
indexed with the local apic id.
Signed-off-by: NRavikiran Thirumalai <kiran@scalex86.org>
Acked-by: NSuresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Improve explanation of the Subject line fields in
Documentation/SubmittingPatches Canonical Patch Format.
Signed-off-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some Legacy megaraid cards can't actually cope with the scatter/gather
version of the READ CAPACITY command (which is what we now send them
since altering all SCSI internal I/O to go via the block layer).  Fix
this (and a few other broken megaraid driver assumptions) by sending
the non-sg version of the command if the sg list only has a single
element.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>