- 30 1月, 2009 9 次提交
-
-
由 Jouni Malinen 提交于
Add mechanism for managing BIP keys (IGTK) and integrate BIP into the TX/RX paths. Signed-off-by: NJouni Malinen <j@w1.fi> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Implement Broadcast/Multicast Integrity Protocol for management frame protection. This patch adds the needed definitions for the new information element (MMIE) and implementation for the new "encryption" type (though, BIP is actually not encrypting data, it provides only integrity protection). These routines will be used by a follow-on patch that enables BIP for multicast/broadcast robust management frames. Signed-off-by: NJouni Malinen <j@w1.fi> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Jouni Malinen 提交于
Add flags for setting STA entries and struct ieee80211_if_sta to indicate whether management frame protection (MFP) is used. Signed-off-by: NJouni Malinen <j@w1.fi> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This will be needed for drivers that set the IEEE80211_HW_NO_STACK_DYNAMIC_PS flag and still want to handle dynamic PS. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Reviewed-by: NKalle Valo <kalle.valo@nokia.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
I missed this during review of "mac80211: Fix tx power setting", the user_power_level shouldn't be available to the driver but rather be an internal value used to calculate the value for the driver. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rami Rosen 提交于
This patch removes an unused declaration of dot11WEPUndecryptableCount (an snmp counter) in ieee80211_local structure and its usage in debugfs.c since this counter is not incremented/decremented anywhere. Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Move to the advertised channel on reception of a CSA element. This is needed for 802.11h compliance. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
This patch enables mac80211 to send a null frame and also to check for tim in the beacon if dynamic power save is enabled. Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
As TKIP is not updated to new security needs which arise when TKIP is used to encrypt A-MPDU aggregated data frames, IEEE802.11n does not allow any cipher other than CCMP (Which has new extensions defined) as pairwise cipher between HT peers. When such configuration (TKIP/WEP in HT) is forced, we still associate in non-HT mode (11a/b/g). Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 20 12月, 2008 4 次提交
-
-
由 Kalle Valo 提交于
This patch implements dynamic power save for mac80211. Basically it means enabling power save mode after an idle period. Implementing it dynamically gives a good compromise of low power consumption and low latency. Some hardware have support for this in firmware, but some require the host to do it. The dynamic power save is implemented by adding an timeout to ieee80211_subif_start_xmit(). The timeout can be enabled from userspace with Wireless Extensions. For example, the command below enables the dynamic power save and sets the time timeout to 500 ms: iwconfig wlan0 power timeout 500m Power save now only works with devices which handle power save in firmware. It's also disabled by default and the heuristics when and how to enable is considered as a policy decision and will be left for the userspace to handle. In case the firmware has support for this, drivers can disable this feature with IEEE80211_HW_NO_STACK_DYNAMIC_PS. Big thanks to Johannes Berg for the help with the design and code. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
This is a preparation for the dynamic power save support. In future there are two paths to stop the master queues and we need to track this properly to avoid starting queues incorrectly. Implement this by adding a status array for each queue. The original idea and design is from Johannes Berg, I just did the implementation based on his notes. All the bugs are mine, of course. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Kalle Valo 提交于
Also disable power save when disassociated. It makes no sense to have power save enabled while disassociated. iwlwifi seems to have this check in the driver, but it's better to do this in mac80211 instead. Signed-off-by: NKalle Valo <kalle.valo@nokia.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
HT management is done differently for AP and STA modes, unify to just the ->config() callback since HT is fundamentally a PHY property and cannot be per-BSS. Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote the channel type ( NO_HT, HT20, HT40+, HT40- ). Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 13 12月, 2008 1 次提交
-
-
由 Rami Rosen 提交于
This patch removes unneeded member (skbuff) from ieee80211_ibss_add_sta() method in its declaration (in ieee80211_i.h) and its callers (in rx.c and mlme.c) This patch removes unneeded member from struct ieee80211_rx_data in ieee80211_i.h. (Originally posted as two patches. -- JWL) Signed-off-by: NRami Rosen <ramirose@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 12月, 2008 1 次提交
-
-
由 Jouni Malinen 提交于
This patch adds new NL80211_CMD_SET_WIPHY attributes NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow userspace to set the operating channel (e.g., hostapd for AP mode). Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 11月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
Remove the SSID from the driver API since now there is no driver that requires knowing the SSID and I think it's unlikely that any hardware design that does require the SSID will play well with mac80211. This also removes support for setting the SSID in master mode which will require a patch to hostapd to not try. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 11月, 2008 10 次提交
-
-
由 colin@cozybit.com 提交于
The two new commands are NL80211_CMD_GET_MESH_PARAMS and NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum, NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration parameters. Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h. nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages and ask the driver to get or set the configuration. This is done via two new function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops. Signed-off-by: NColin McCabe <colin@cozybit.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
So after the previous changes we were still unhappy with how convoluted the API is and decided to make things simpler for everybody. This completely changes the rate control API, now taking into account 802.11n with MCS rates and more control, most drivers don't support that though. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The HT handling has the following deficiencies, which I've (partially) fixed: * it always uses the AP info even if there is no AP, hence has no chance of working as an AP * it pretends to be HW config, but really is per-BSS * channel sanity checking is left to the drivers * it generally lets the driver control too much HT enabling is still wrong with this patch if you have more than one virtual STA mode interface, but that never happens currently. Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be wrong, see the comment in ieee80211_enable_ht(). Additionally, this fixes a number of bugs: * mac80211: ieee80211_set_disassoc doesn't notify the driver any more since the refactoring * iwl-agn-rs: always uses the HT capabilities from the wrong stuff mac80211 gives it rather than the actual peer STA * ath9k: a number of bugs resulting from the broken HT API I'm not entirely happy with putting the HT capabilities into struct ieee80211_sta as restricted to our own HT TX capabilities, but I see no cleaner solution for now. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Move bss_conf into the vif struct so that drivers can access it during ->tx without having to store it in the private data or similar. No driver updates because this is only for when they want to start using it. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Instead of having a separate callback, use the HW config callback with a new flag to change retry limits. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
I've come to think that not providing sequence numbers for the normal STA mode case was a mistake, at least two drivers now had to implement code they wouldn't otherwise need, and I believe at76_usb and adm8211 might be broken. This patch makes mac80211 assign a sequence number to all those frames that need one except beacons. That means that if a driver only implements modes that do not do beaconing it need not worry about the sequence number. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This makes mac80211 notify the driver which configuration actually changed, e.g. channel etc. No driver changes, this is just plumbing, driver authors are expected to act on this if they want to. Also remove the HW CONFIG debug printk, it's incorrect, often we configure something else. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Never actually used. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch cleans up a number of things: * the unusable definition of the HT capabilities/HT information information elements * variable names that are hard to understand * mac80211: move ieee80211_handle_ht to ht.c and remove the unused enable_ht parameter * mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht * mac80211: fix bug with casting the result of ieee80211_bss_get_ie to an information element _contents_ rather than the whole element, add size checking (another out-of-bounds access bug fixed!) * mac80211: remove some unused return values in favour of BUG_ON checking * a few minor other things Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rami Rosen 提交于
This patch removes unused definition of struct sta_attribute in net/mac80211/ieee80211_i.h. Signed-off-by: NRami Rosen <ramirose@gmail.com> Acked-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 10月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
There's no checking that the HT IEs are of the right length which can be used by an attacker to cause an out-of-bounds access by sending a too short HT information/capability IE. Fix it by simply pretending those IEs didn't exist when too short. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 9月, 2008 2 次提交
-
-
由 Johannes Berg 提交于
Long awaited, hard work. This patch totally cleans up the rate control API to remove the requirement to include internal headers outside of net/mac80211/. There's one internal use in the PID algorithm left for mesh networking, we'll have to figure out a way to clean that one up and decide how to do the peer link evaluation, possibly independent of the rate control algorithm or via new API. Additionally, ath9k is left using the cross-inclusion hack for now, we will add new API where necessary to make this work properly, but right now I'm not expert enough to do it. It's still off better than before. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
There's no need to register the master netdev with cfg80211, in fact, this is quite dangerous and lead to having to add checks for the master interface all over the config handlers. This patch removes the "ieee80211_ptr" from the master iface in favour of having a small netdev_priv() associated with the master interface that stores the ieee80211_local pointer. Because of this, a lot of code in the configuration handlers can go away. To make this patch easier to verify I have also removed a number of wiphy_priv() calls in favour of getting the sdata first and then the local pointer from that. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 16 9月, 2008 10 次提交
-
-
由 Johannes Berg 提交于
The beacon counters mac80211 keeps are only used for debugfs, unfortunately, they are incorrect for many hardware designs, namely any design that has a beacon template. Hence, remove the counters so we don't create the impression they are usable. This also allows removing the beacon MESH #ifdef again. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Move the code to handle regular interfaces out of main.c and into iface.c, keep only the master interface stuff in main.c. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
There's really no reason for mac80211 to be using its own interface type defines. Use the nl80211 types and simplify the configuration code a bit: there's no need to translate them any more now. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Drivers need to know the basic rateset to be able to configure the ACK/CTS programming in hardware correctly. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Some comments refer to 80211.o or similar; also remove a comment about implementing fragments better, we really have better things to do. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
Most of the scan functions are called ieee80211_sta_scan_* or similar, make clean it up so they are all just called ieee80211_scan_*. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The bridge_packets configuration really should be per virtual interface (theoretically per AP/VLAN, but this is much easier); there currently is no way to set it yet though. Also invert the option to "NO_BRIDGE_PACKETS" so the default is to bridge. While at it, also document the flags properly. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
It really doesn't belong into the wireless extensions code. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This way all the utility functions are at the top, then the state machine and externally callable functions are moved to the bottom. Also clean up ieee80211_i.h a bit and add a few comments about which functions are called from where. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This patch splits off mesh handling from the STA/IBSS. Unfortunately it increases mesh code size a bit, but I think it makes things clearer. The patch also reduces per-interface run-time memory usage. Also clean up a few places where ifdef is not required. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 9月, 2008 1 次提交
-
-
由 Johannes Berg 提交于
The ieee80211_sta_tx function isn't MLME code any more, it's getting used by a lot of code. Move it to utils and rename it to ieee80211_tx_skb. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-