- 23 6月, 2009 40 次提交
-
-
由 Trent Piepho 提交于
In the TRY_FMT handler the function get_scale() is called to find what the scaler hardware will produce for a requested size. The problem is that get_scale(struct cx231xx *dev, ..., unsigned int *vscale, unsigned int *hscale) saves the calculated scale values into both the pointer arguments and into dev's hscale and vscale fields. TRY_FMT shouldn't actually change anything in the device state. The code to in get_scale() that writes to dev->[hv]scale can just be deleted. In all cases when dev's fields should be modified, get_scale() was called with get_scale(dev, ..., &dev->hscale, &dev->vscale), so dev was getting updated anyway. This didn't actually cause a problem because nothing ever actually made use of the hscale and vscale fields. I changed cx231xx_resolution_set() to use those fields rather than re-calculate them with a call to get_scale(). Updating [hv]scale in cx231xx_resolution_set() isn't necessary because every call of cx231xx_resolution_set() was already preceded by a call to get_scale() or setting the [hv]scale fields, so they will be always be up-to-date w.r.t. width and height. Removing the call to get_scale() from cx231xx_resolution_set() allowed making get_scale() a static function, which is a good thing for something with such a short name. There is already another function with the same name in the em28xx driver, but that one is static. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. It appears that the em2800 can only scale by 50% or 100%, i.e. the only heights supported might be 240 and 480. In that case the old code would set any height other than 240 to 480. Request 240 get 240, but request 239 and then you get 480. Change it to round to the nearest supported value. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com> Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. The existing code was casting pointers to u32 and to unsigned int into pointers to u16. This could mess up if someone passed in an image size greater than 65,535 and on big-endian platforms it won't work at all. The existing bounding code would shrink an image if it was too big, but returned ERANGE if it was too small. The code will not shrink or expand as necessary. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
The v4l function has a better algorithm for aligning image size. For instance the old code would change 159x243 into 156x240 to meet the alignment requirements. The new function will use 160x243, which is a lot closer to what was asked for originally. Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Trent Piepho 提交于
Most hardware has limits on minimum and maximum image dimensions and also requirements about alignment. For example, image width must be even or a multiple of four. Some hardware has requirements that the total image size (width * height) be a multiple of some power of two. v4l_bound_align_image() will enforce min and max width and height, power of two alignment on width and height, and power of two alignment on total image size. It uses an efficient algorithm that will try to find the "closest" image size that meets the requirements. Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Add a new s_config core ops call: this is called with the irq and platform data to be used to initialize the subdev. Added new v4l2_i2c_new_subdev_cfg and v4l2_i2c_new_subdev_board calls that allows you to pass these new arguments. The existing v4l2_i2c_new_subdev functions were modified to also call s_config. In the future the existing v4l2_i2c_new_subdev functions will be replaced by a single v4l2_i2c_new_subdev function similar to v4l2_i2c_new_subdev_cfg but without the irq and platform_data arguments. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Isely 提交于
This change does not change any outward behavior; it merely chops down some large if-conditions with embedded assignments into something a little more maintainable for others (I of course never had a problem with this...). Signed-off-by: NMike Isely <isely@pobox.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Isely 提交于
The pvrusb2 driver has a concept of "routing scheme" which defines which physical inputs should be connected based on application's choice of logical input. The correct "routing scheme" depends on the specific device since different devices might wire up their muxes Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Isely 提交于
Change default frequency to be US Broadcast channel 3 - with the transition to d igital the previous value has now become useless. This change is PURELY to help with my testing (I need to set some kind of default so it might as well be some thing usable). Signed-off-by: NMike Isely <isely@pobox.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Isely 提交于
The cx25840 module's VBI initialization logic uses the current video standard as part of its internal algorithm. This therefore means that we probably need to make sure that the correct video standard has been set before initializing VBI. (Normally we would not care about VBI, but as described in an earlier changeset, VBI must be initialized correctly on the cx25840 in order for the chip's hardware scaler to operate correctly.) It's kind of messy to force the video standard to be set before initializing VBI (mainly because we can't know what the app really wants that early in the initialization process). So this patch does the next best thing: VBI is re-initialized after any point where the video standard has been set. Signed-off-by: NMike Isely <isely@pobox.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Mike Isely 提交于
The cx25840 module requires that its VBI initialization entry point be called in order for hardware-scaled video capture to work properly - even if we don't care about VBI. Making this behavior even more subtle is that if the capture resolution is set to 720x480 - which is the default that the pvrusb2 driver sets up - then the cx25840 bypasses the hardware scaler. Therefore this problem does not manifest itself until some other resolution, e.g. 640x480, is tried. MythTV typically defaults to 640x480 or 480x480, which means that things break whenever the driver is used with MythTV. This all has been known for a while (since at least Nov 2006), but recent changes in the pvrusb2 driver (specifically in regards to sub-device support) caused this to break again. VBI initialization must happen *after* the chip's firmware is loaded, not before. With this fix, 24xxx devices work correctly again. A related fix that is part of this changeset is that now we re-initialize VBI any time after we issue a reset to the cx25840 driver. Issuing a chip reset erases the state that the VBI setup previously did. Until the HVR-1950 came along this subtlety went unnoticed, because the pvrusb2 driver previously never issued such a reset. But with the HVR-1950 we have to do that reset in order to correctly transition from digital back to analog mode - and since the HVR-1950 always starts in digital mode (required for the DVB side to initialize correctly) then this device has never had a chance to work correctly in analog mode! Analog capture on the HVR-1950 has been broken this *ENTIRE* time. I had missed it until now because I've usually been testing at the default 720x480 resolution which does not require scaling... What fun. By re-initializing VBI after a cx25840 chip reset, correct behavior is restored. Signed-off-by: NMike Isely <isely@pobox.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Ensure that we're programming the tda18271 tuner with the correct IF frequencies to match the programming of the TDA10048 DVB-T demod for the HVR1200 and HVR1700 products. Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Michael Krufky 提交于
Thanks for Terry Wu for pointing out the missing entry. Cc: Terry Wu <terrywu2009@gmail.com> Signed-off-by: NMichael Krufky <mkrufky@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
The variable 'rc' could be used uninitialized in the cx231xx_capture_start function. Sri informed me that it should be initialized to -1. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
tcm825x_remove is not necessarily called on module exit, it can also be called when the i2c_adapter is removed. While the i2c adapter might never be removed on an embedded system, in practice this sensor driver can also be used in e.g. a USB webcam where this is a perfectly acceptable thing to do. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
rxsubchans was only set when stereo was detected, otherwise it was left to 0 instead of setting it to mono. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
Make it very clear that this header should not be used for i2c drivers that do not need to be compiled for pre-2.6.26 kernels. As soon as the minimum supported kernel in the v4l-dvb repository becomes 2.6.26 or up, then this header should be removed entirely. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
gcc 4.3.1 generates this warning: v4l/smscoreapi.c: In function 'smscore_gpio_configure': v4l/smscoreapi.c:1481: warning: 'GroupNum' may be used uninitialized in this function v4l/smscoreapi.c:1480: warning: 'TranslatedPinNum' may be used uninitialized in this function While in practice this will not happen, it is something that the compiler can't determine. Initializing these two local variables to 0 suppresses this warning. Cc: Udi Atar <udi.linuxtv@gmail.com> Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans Verkuil 提交于
A previous change (v4l2-common: remove v4l2_ctrl_query_fill_std) broke the handling of class controls in VIDIOC_QUERYCTRL. The MPEG class control was broken for all drivers that use the cx2341x module and the USER class control was broken for ivtv and cx18. This change adds back proper class control support. Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Add an IR profile for the EVGA inDtube remote control (which is an NEC type remote) Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
Add support for the EVGA inDtube. Both ATSC and analog side validated as fully functional. Thanks to Jake Crimmins from EVGA for providing the correct GPIO info. Thanks to Alan Hagge for doing all the device testing. Thanks to Greg Williamson for providing hardware for testing. Cc: Jake Crimmins <jcrimmins@evga.com> Cc: Alan Hagge <ahagge@gmail.com> Cc: Greg Williamson <cheeseboy16@gmail.com> Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Devin Heitmueller 提交于
In cases where the board had a default USB ID, we would not indentify the board until after the call to em28xx_set_mode(). As a result, for those boards the analog GPIOs were not being set before probing the i2c bus for devices (the probe would occur with the GPIOs being all high). Make a call to em28xx_set_mode() so that the GPIOs are set properly before probing the i2c bus for devices. This problem was detected with the EVGA inDtube, where the tvp5150 is not powered on unless GPIO1 is pulled low. Signed-off-by: NDevin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Abylay Ospan 提交于
Signed-off-by: NAbylay Ospan <aospan@netup.ru> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Abylay Ospan 提交于
Signed-off-by: NAbylay Ospan <aospan@netup.ru> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Igor M. Liplianin 提交于
Signed-off-by: NIgor M. Liplianin <liplianin@netup.ru> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans de Goede 提交于
Name saturation control saturation, not color and make the default less saturated (the old default was overdoing it). Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans de Goede 提交于
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise the picture is upside down. It is better to instead invert the meaning of the control in the set function, and have the default be no vflip, as one would expect vflip enabled to be upside down. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans de Goede 提交于
gspca_sonixj: Add light frequency control Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans de Goede 提交于
gspca_sonixj: enable autogain control for the ov7620, and not only make it enable autogain but also auto exposure (and do the same for the ov7648). Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
由 Hans de Goede 提交于
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer overflows during my testing of a "Premier" 0c45:613e cam Signed-off-by: NHans de Goede <hdegoede@redhat.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-