- 30 4月, 2009 2 次提交
-
-
由 Ben Hutchings 提交于
Add a PORT_OTHER to represent all other physical port types. Current NICs generally do not allow switching between multiple port types in software so specific types should not be needed. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John Dykstra 提交于
These two memory barriers in performance-critical paths are not needed on x86. Even if some other architecture does buffer PCI I/O space writes, the existing memory-mapped I/O barriers are unlikely to be what is needed. Signed-off-by: NJohn Dykstra <john.dykstra1@gmail.com> Acked-by: NDon Fry <pcnet32@verizon.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 4月, 2009 4 次提交
-
-
由 Don Skidmore 提交于
We were calling pci_enable_wake() twice in a row for both D3_hot and D3_cold. This replaces those calls with a call to pci_wake_from_d3() to avoid issues with PCI PM vs ordering constraints. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
o hold the firmware in memory across suspend, since filesystem may not be up after resuming. o reset the chip after requesting firmware, to minimize downtime for NC-SI. Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
o move related fields into netxen_recv_context struct. o allocate rx buffer and descriptor rings dynamically. Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Dhananjay Phadke 提交于
Firmware starting 4.0.402 started supporting link events, disable it for older firmwares. Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 28 4月, 2009 16 次提交
-
-
由 Kumar Gala 提交于
cacheable_memzero() is completely overkill for the clearing out the FCB block which is only 8-bytes. The compiler should easily optimize this with memset. Additionally, cacheable_memzero() only exists on ppc32 and thus breaks builds of gianfar on ppc64. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Arnaldo Carvalho de Melo 提交于
These are later assigned to other values without being used meanwhile. Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eric Dumazet 提交于
netif_tx_queue_stopped(txq) is most of the time false. Yet its cost is very expensive on SMP. static inline int netif_tx_queue_stopped(const struct netdev_queue *dev_queue) { return test_bit(__QUEUE_STATE_XOFF, &dev_queue->state); } I saw this on oprofile hunting and bnx2 driver bnx2_tx_int(). We probably should split "struct netdev_queue" in two parts, one being read mostly. __netif_tx_lock() touches _xmit_lock & xmit_lock_owner, these deserve a separate cache line. Signed-off-by: NEric Dumazet <dada1@cosmosbay.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Grant Likely 提交于
Previous rework to ucc_geth.c to add of_mdio support (net: Rework ucc_geth driver to use of_mdio infrastructure) added a block of code which broke older openfirmware device trees which this case. This patch removes the offending blurb. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Kumar Gala 提交于
CONFIG_DUET doesn't exist anymore, remove all the code that exists to support it. [ Simplify fs_init() even further -DaveM ] Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nelson, Shannon 提交于
Ayyappan at VMware noticed that we're missing this check from ixgbe which is in our other drivers. The difference with this implementation from our other drivers is that this checks all the tx queues rather than just tx[0]. Signed-off-by: NShannon Nelson <shannon.nelson@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Nelson, Shannon 提交于
Update the interrupt management to correctly handle greater than 16 queue vectors. Signed-off-by: NShannon Nelson <shannon.nelson@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This patch enables hardware receive side coalescing for 82599 hardware. 82599 can merge multiple frames from the same TCP/IP flow into a single structure that can span one ore more descriptors. The accumulated data is arranged similar to how jumbo frames are arranged with the exception that other packets can be interlaced inbetween. To overcome this issue a next pointer is included in the written back descriptor which indicates the next descriptor in the writeback sequence. This feature sets the NETIF_F_LRO flag and clearing it via the ethtool set flags operation will also disable hardware RSC. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
Inspired by: Vlad Yasevich <vladislav.yasevich@hp.com> This is the code to enable ixgbe for hardware offload support of CRC32c on both transmit and receive of SCTP traffic. only 82599 supports this offload, not 82598. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
Originally from: Vlad Yasevich <vladislav.yasevich@hp.com> This patch, both the driver portion and the sctp code was modified by Jesse Brandeburg and is Copyright(c) 2009 Intel Corporation. Thanks go to Vlad for starting this work. Intel 82576 chipset supports SCTP checksum offloading. This patch enables this functionality in the driver. A new NETIF feature is introduced for SCTP checksum offload. If the driver supports CRC32c checksum, it can set this feature flag. The hardware can offload both transmit and receive. Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jesse Brandeburg 提交于
this is the sctp code to enable hardware crc32c offload for adapters that support it. Originally by: Vlad Yasevich <vladislav.yasevich@hp.com> modified by Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
Both of these drivers do a check to verify ip_summed is set to CHECKSUM_UNNECESSARY prior to passing the packet to GRO. GRO itself already does such a check so it is redundant and can be removed as this will likely cause out of order issues when receiving a packet that didn't pass checksum validation. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
The igb driver was being incorrectly setup to only allow disabling receive checksum if multiqueue was disabled. This change corrects that so that RXCSUM is configured regardless of queue configuration. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
This change updates the timeout logic so that it is not possible to have a sucessful check for message and still return an error if countdown = 0. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Reported-by: NJuha Leppanen <juha_motorsportscom@luukku.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Magnus Damm 提交于
This is V2 of the smsc911x fifo byteswap patch. The smsc911x hardware supports both big and little and endian hardware configurations, and the linux smsc911x driver currently detects word order. For correct operation on big endian platforms lacking swapped byte lanes the following patch is needed. Only fifo data is swapped, register data does not require any swapping. Signed-off-by: NMagnus Damm <damm@igel.co.jp> Acked-by: NSteve Glendinning <steve.glendinning@smsc.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jie Yang 提交于
Disable L1/L0s when link detected. We enable L1/L0s when link connected before, but there is some hareware error on some platform. So just diable this feature when link connected. This feature is about power saving. Signed-off-by: NJie Yang <jie.yang@atheros.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 4月, 2009 18 次提交
-
-
由 Herbert Xu 提交于
On a brand new GRO skb, we cannot call ip_hdr since the header may lie in the non-linear area. This patch adds the helper skb_gro_network_header to handle this. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Herbert Xu 提交于
The skb_gro_* code fails to handle the case where a header starts in the linear area but ends in the frags area. Since the goal of skb_gro_* is to optimise the case of completely non-linear packets, we can simply bail out if we have anything in the linear area. Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
>From now on FW will be downloaded from the binary file using request_firmware. There will be different files for every supported chip. Currently 57710 (e1) and 57711 (e1h). File names have the following format: bnx2x-<chip version>-<FW version>.fw. ihex versions of current FW files are submitted in the next patch. Each binary file has a header in the following format: struct bnx2x_fw_file_section { __be32 len; __be32 offset; } struct bnx2x_fw_file_hdr { struct bnx2x_fw_file_section init_ops; struct bnx2x_fw_file_section init_ops_offsets; struct bnx2x_fw_file_section init_data; struct bnx2x_fw_file_section tsem_int_table_data; struct bnx2x_fw_file_section tsem_pram_data; struct bnx2x_fw_file_section usem_int_table_data; struct bnx2x_fw_file_section usem_pram_data; struct bnx2x_fw_file_section csem_int_table_data; struct bnx2x_fw_file_section csem_pram_data; struct bnx2x_fw_file_section xsem_int_table_data; struct bnx2x_fw_file_section xsem_pram_data; struct bnx2x_fw_file_section fw_version; } Each bnx2x_fw_file_section contains the length and the offset of the appropriate section in the binary file. Values are stored in the big endian format. Data types of arrays: init_data __be32 init_ops_offsets __be16 XXsem_pram_data u8 XXsem_int_table_data u8 init_ops struct raw_op { u8 op; __be24 offset; __be32 data; } fw_version u8 >From now boundaries of a specific initialization stage are stored in init_ops_offsets array instead of being defined by separate macroes. The index in init_ops_offsets is calculated by BLOCK_OPS_IDX macro: #define BLOCK_OPS_IDX(block, stage, end) \ (2*(((block)*STAGE_IDX_MAX) + (stage)) + (end)) Security: In addition to sanity check of array boundaries bnx2x will check a FW version. Additional checks might be added in the future. Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Vladislav Zolotarov 提交于
Signed-off-by: NVladislav Zolotarov <vladz@broadcom.com> Signed-off-by: NEilon Greenstein <eilong@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David Woodhouse 提交于
When creating a certain types of VPN, NetworkManager will first attempt to find an available tun device by iterating through 'vpn%d' until it finds one that isn't already busy. Then it'll set that to be persistent and owned by the otherwise unprivileged user that the VPN dæmon itself runs as. There's a race condition here -- during the period where the vpn%d device is created and we're waiting for the VPN dæmon to actually connect and use it, if we try to create _another_ device we could end up re-using the same one -- because trying to open it again doesn't get -EBUSY as it would while it's _actually_ busy. So solve this, we add an IFF_TUN_EXCL flag which causes tun_set_iff() to fail if it would be opening an existing persistent tundevice -- so that we can make sure we're getting an entirely _new_ device. Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Simon Arlott 提交于
Values of dB between -0.99 and -0.01 will be output with the wrong sign. This converts the negative value to positive and outputs it with a "-" prefix. Signed-off-by: NSimon Arlott <simon@fire.lp0.eu> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 roel kluin 提交于
mac_to_intf() can return -1 when no device or function is found, but when mac->dma_if is unsigned. The error wasn't noticed. Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Acked-by: NOlof Johansson <olof@lixom.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Neil Horman 提交于
When I initially implemented this protocol, I disregarded the use of netlink attribute headers, thinking for my purposes they weren't needed. I've come to find out that, as I'm starting to work with sending down messages with associated data (like config messages), the kernel code spits out warnings about trailing data in a netlink skb that doesn't have an associated header on it. As such, I'm going to start including attribute headers in my netlink transaction, and so for completeness, I should likely include them on messages bound from the kernel to user space. This patch adds that header to the kernel, and bumps the protocol version accordingly Signed-off-by: NNeil Horman <nhorman@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Waskiewicz Jr, Peter P 提交于
82598 and 82599 do not support SFP 1G modules. Instead of allowing the driver to load, but never get link, rejecting the module and displaying a useful message is more preferrable. The framework for displaying the failure message already exists, now we just need to detect and reject the SFP modules. Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Duyck 提交于
The igb driver was switching between adapter->itr containing the EITR value and the number of interrupts per second. This resulted in high latencies being seen after brining the interface down and then back up. To resolve the issue the itr value will now only contain the value that should be programmed into EITR. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Beregalov 提交于
Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Acked-by: NRam Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Alexander Beregalov 提交于
If vpath is NULL then hldev is NULL also. Signed-off-by: NAlexander Beregalov <a.beregalov@gmail.com> Acked-by: NRam Vepa <ram.vepa@neterion.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
Pointed out by Sean E. Millichamp. Quote from Documentation/networking/bonding.txt: "Note that when a bonding interface has no active links, the driver will immediately reuse the first link that goes up, even if the updelay parameter has been specified (the updelay is ignored in this case). If there are slave interfaces waiting for the updelay timeout to expire, the interface that first went into that state will be immediately reused. This reduces down time of the network if the value of updelay has been overestimated, and since this occurs only in cases with no connectivity, there is no additional penalty for ignoring the updelay." This patch actually changes the behaviour in this way. Signed-off-by: NJiri Pirko <jpirko@redhat.com> drivers/net/bonding/bond_main.c | 8 ++++++++ 1 files changed, 8 insertions(+), 0 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jiri Pirko 提交于
This patch only changes the order of interfaces to use for checking slave link status in bond_check_dev_link() to priorize ethtool interface. Should safe some troubles as ethtool seems to be more supported. Jirka Signed-off-by: NJiri Pirko <jpirko@redhat.com> drivers/net/bonding/bond_main.c | 26 ++++++++++++-------------- 1 files changed, 12 insertions(+), 14 deletions(-) Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Grant Likely 提交于
Modules are not supposed to use any of the *_initcall*() hooks as the entry point. fsl_pq_mdio.c was using subsys_initcall_sync() instead of module_init() to guarantee that the MDIO bus was initialized before the Ethernet driver goes looking for the phy. However, the recent OF helpers rework happens to also make sure PHY connection is deferred to .open time, so using an initcall is no longer necessary. This patch replaces the initcall with a more traditional an accepted module_init() call. Tested on Freescale MPC8349emitxgp eval board. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Grant Likely 提交于
This patch adds support for the Xilinx ll_temac 10/100/1000 Ethernet device. The ll_temac ipcore is typically used on Xilinx Virtex and Spartan designs attached to either a PowerPC 4xx or Microblaze processor. At the present moment, this driver only works with Virtex5 PowerPC designs because it assumes DCR is used to access the DMA registers. However, the low level access to DMA registers is abstracted and it should be easy to adapt for the other implementations. I'm posting this driver now as an RFC. There are still some things that need to be tightened up, but it does appear to be stable. Derived from driver code written by Yoshio Kashiwagi and David H. Lynch Jr. Tested on Xilinx ML507 eval board with Base System Builder generated FPGA design. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca> Acked-by: NAndy Fleming <afleming@freescale.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-